Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2015.08
RM19Y0E _58 Vehicle Interior _003010 SUPPLEMENTAL RESTRAINT SYSTEMS _0015213 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  Diagnosis Circuit  


DESCRIPTION

DTC output mode is set by connecting terminals ECUT and E of the DLC3.

DTCs are output by the blinking of the SRS warning light.

HINT:
·

When each warning light continues blinking, a ground short in the wiring of terminal ECUT of the DLC3 or an internal ground short in each ECU is suspected.

·

A DTC output mode signal is transmitted through the CAN communication system to each ECU, including the airbag ECU assembly. Thus, when all systems do not enter DTC output mode, there may be an ECM malfunction.



WIRING DIAGRAM

C261918E16
1.635,0.552 2.125,0.75 0.49,0.198 10 false CANL 1.615,1.115 2.104,1.313 0.49,0.198 10 false CANH 1.25,2.615 3.177,3.094 1.927,0.479 10 false Combination Meter Assembly 1.26,3.438 1.542,3.635 0.281,0.198 10 false E 1.635,3.438 2.083,3.625 0.448,0.188 10 false ECUT 2.042,3.302 2.26,3.49 0.219,0.188 10 false 13 1.25,2.448 1.604,2.646 0.354,0.198 10 false E34 2.063,0.427 2.302,0.635 0.24,0.208 10 false 8 2.052,0.99 2.292,1.198 0.24,0.208 10 false 9 2.063,1.573 2.302,1.781 0.24,0.208 10 false 12 1.885,1.677 2.167,1.865 0.281,0.188 10 false T 5.771,0.427 6.01,0.635 0.24,0.208 10 false 25 5.771,0.979 6.01,1.188 0.24,0.208 10 false 26 6,0.552 6.49,0.75 0.49,0.198 10 false CANL 6.01,1.115 6.5,1.313 0.49,0.198 10 false CANH 1.229,3.917 1.583,4.115 0.354,0.198 10 false E12 5.688,3.823 6.021,4.021 0.333,0.198 10 false E76 1.229,4.083 1.719,4.281 0.49,0.198 10 false DLC3 0.531,4.438 3.063,4.656 2.531,0.219 10 false : CAN Communication Line 5.698,4 7.156,4.375 1.458,0.375 10 false Airbag ECU Assembly 1.104,3.313 1.25,3.552 0.146,0.24 10 false 4

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag ECU assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication DTC is output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

Result:
Proceed to
DTCs are output
DTC is not output




DTCs are output

DTC is not output

2.CHECK HARNESS AND CONNECTOR (DLC3 - COMBINATION METER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (DLC3 - COMBINATION METER ASSEMBLY)
a.

Turn the ignition switch off.

C332488C01
3.667,0.667 4.083,0.917 0.417,0.25 0.417,0.667 0.833,0.917 0.417,0.25 2.042,1.031 2.156,1.344 2.156,1.344 2.323,1.344 true 5.479,0.917 5.677,1.375 5.677,1.375 5.885,1.375 true 0.5,0.115 0.813,0.271 0.313,0.156 10 false *a 3.802,0.125 4.115,0.281 0.313,0.156 10 false *b 0.51,0.708 0.823,0.865 0.313,0.156 10 false E12 3.771,0.708 4.083,0.865 0.313,0.156 10 false E34 2.365,1.271 2.885,1.5 0.521,0.229 10 false ECUT 5.948,1.292 6.26,1.448 0.313,0.156 10 false T
*a Front view of DLC3 *b Front view of wire harness connector
(to Combination Meter Assembly)



b.

Disconnect the connector from the combination meter assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E12-13 (ECUT) - E34-12 (T) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)
a.
C198509C25
1.5,0.333 1.917,0.583 0.417,0.25 1.583,1.094 1.354,1.76 1.354,1.76 1.177,1.76 true 0.094,0.125 0.313,0.354 0.219,0.229 10 false *a 1.021,1.688 1.302,1.875 0.281,0.188 10 false E 1.594,0.375 2.031,0.625 0.438,0.25 10 false E12
*a Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E12-4 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)
a.
C253599C25
1.469,0.417 1.885,0.667 0.417,0.25 1.854,1.302 2.135,0.688 2.135,0.688 2.323,0.688 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.563,0.458 1.927,0.677 0.365,0.219 10 false E34 2.375,0.615 2.688,0.771 0.313,0.156 10 false T
*a Front view of wire harness connector
(to Combination Meter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E34-12 (T) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR OR EACH ECU