Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM › from 2015.08
RM19Y0E _58 Vehicle Interior _003006 THEFT DETERRENT / KEYLESS ENTRY _0015192 ENGINE IMMOBILISER SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  B2780/15  Key Switch OFF Malfunction  


DESCRIPTION

This DTC output if the transponder key ECU does not detect that the unlock warning switch is ON even when the ignition switch is ON. Under normal conditions, the unlock warning switch is ON when the ignition switch is ON.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2780/15 Key Switch OFF Malfunction With the ignition switch set to ON position, the key switch OFF is be detected for 500 ms or more (1 trip detection logic*).
·

Steering column upper with switch bracket assembly (unlock warning switch)

·

Transponder key ECU assembly

·

Wire harness or connector


DTC Output Confirmation Operation

·

Ignition switch ON




*: Only output while a malfunction is present.

Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC No. Data List and Active Test
B2780/15 KEY SW(KSW)

WIRING DIAGRAM

B413852E02
5.531,2.104 6.969,2.76 1.438,0.656 10 false Transponder Key ECU Assembly 5.531,1.917 6.063,2.365 0.531,0.448 10 false E58 2.177,0.729 2.906,1.167 0.729,0.438 10 false HORN 0.313,0.542 1.375,0.958 1.063,0.417 10 false from Battery 3.333,0.448 3.667,0.771 0.333,0.323 10 false 2 4.521,0.448 4.854,0.771 0.333,0.323 10 false 1 3.542,0.542 3.875,0.865 0.333,0.323 10 false + 4.292,0.531 4.625,0.854 0.333,0.323 10 false - 2.771,0.927 5.521,1.729 2.75,0.802 10 false Steering Column Upper with Switch Bracket Assembly (Unlock Warning Switch) 5.844,0.552 6.573,0.99 0.729,0.438 10 false KSW 5.854,1.479 6.25,1.74 0.396,0.26 10 false E 5.573,1.365 5.969,1.625 0.396,0.26 10 false 14 5.615,0.448 6.01,0.708 0.396,0.26 10 false 4 2.781,0.75 3.24,1.083 0.458,0.333 10 false E57

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the transponder key ECU assembly, refer to the Service Bulletin.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.READ VALUE USING GTS or Techstream (KEY SW(KSW))
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Body Electrical / IMB / Data List.


e.

Read the Data List according to the display on the GTS or Techstream.

Body Electrical > IMB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
KEY SW(KSW) Key switch signal ON or OFF ON: Key inserted in ignition key cylinder
OFF: No key in ignition key cylinder
-
Body Electrical > IMB > Data List
Tester Display
KEY SW(KSW)
50003 586 3
OK:

On the GTS or Techstream screen, the display changes between ON and OFF as shown in the table above.


Result:
Proceed to
OK
NG




OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

2.INSPECT STEERING COLUMN UPPER WITH SWITCH BRACKET ASSEMBLY (UNLOCK WARNING SWITCH)
2.INSPECT STEERING COLUMN UPPER WITH SWITCH BRACKET ASSEMBLY (UNLOCK WARNING SWITCH)
E238717C05
1.25,1.865 1.417,1.865 1.417,1.865 1.583,1.365 true 2.177,1.865 2.01,1.865 2.01,1.865 1.844,1.365 true 0.198,0.135 0.573,0.531 0.375,0.396 10 false *a 1.094,1.781 1.552,2.083 0.458,0.302 10 false + 2.271,1.771 2.646,2.104 0.375,0.333 10 false -
*a Component without harness connected
(Steering Column Upper with Switch Bracket Assembly (Unlock Warning Switch))


a.

Disconnect the E57 steering column upper with switch bracket assembly (unlock warning switch) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (-) - 2 (+) No key in ignition key cylinder 10 kΩ or higher
1 (-) - 2 (+) Key inserted into ignition key cylinder Below 1 Ω


Result:
Proceed to
OK
NG




OK

3.CHECK HARNESS AND CONNECTOR (BATTERY, STEERING COLUMN UPPER WITH SWITCH BRACKET ASSEMBLY (UNLOCK WARNING SWITCH) - TRANSPONDER KEY ECU ASSEMBLY)

NG

REPLACE STEERING COLUMN UPPER WITH SWITCH BRACKET ASSEMBLY (UNLOCK WARNING SWITCH)

3.CHECK HARNESS AND CONNECTOR (BATTERY, STEERING COLUMN UPPER WITH SWITCH BRACKET ASSEMBLY (UNLOCK WARNING SWITCH) - TRANSPONDER KEY ECU ASSEMBLY)
a.

Disconnect the E57 steering column upper with switch bracket assembly (unlock warning switch) connector.


b.

Disconnect the E58 transponder key ECU assembly connector.


c.
B297225C05
1.51,0.25 1.927,0.5 0.417,0.25 1.896,1.5 2.125,1.948 2.125,1.948 2.26,1.948 true 1.552,1.51 1.396,1.958 1.396,1.958 1.229,1.958 true 0.208,0.167 0.615,0.552 0.406,0.385 10 false *a 1.594,0.302 2.177,0.635 0.583,0.333 10 false E57 2.333,1.875 2.688,2.177 0.354,0.302 10 false + 1.063,1.875 1.417,2.177 0.354,0.302 10 false -
*a Front view of wire harness connector
(to Steering Column Upper with Switch Bracket Assembly (Unlock Warning Switch))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E57-2 (+) - Body ground Always 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
E57-1 (-) - E58-4 (KSW) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
E57-1 (-) or E58-4 (KSW) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

4.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - BODY GROUND)
a.

Disconnect the E58 transponder key ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E58-14 (E)- Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG




OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR