Home › Engine / Hybrid System › 2NR-VE ENGINE CONTROL › SFI SYSTEM(w/ Air Fuel Ratio Sensor) › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042272 2NR-VE ENGINE CONTROL _0196262 SFI SYSTEM(w/ Air Fuel Ratio Sensor) C

2NR-VE ENGINE CONTROL  SFI SYSTEM(w/ Air Fuel Ratio Sensor)  P0112  Intake Air Temperature Sensor System Open/Low  P0113  Intake Air Temperature Sensor System Open/High  


DESCRIPTION

A283580E01
3.354,2.271 3.74,1.99 false 2.26,0.406 2.833,0.667 0.573,0.26 10 Fig. 1: 3.292,4.271 4.167,4.5 0.875,0.229 10 Temperature 2.396,0.969 2.771,1.219 0.375,0.25 10 (kΩ) 2.281,1.146 2.521,1.365 0.24,0.219 10 30 2.281,1.583 2.521,1.802 0.24,0.219 10 10 2.354,1.875 2.594,2.094 0.24,0.219 10 5 2.354,2.094 2.594,2.313 0.24,0.219 10 3 2.354,2.26 2.51,2.479 0.156,0.219 10 2 2.344,2.531 2.594,2.75 0.25,0.219 10 1 2.24,2.833 2.479,3.052 0.24,0.219 10 0.5 2.24,3.198 2.479,3.417 0.24,0.219 10 0.2 2.24,3.469 2.479,3.688 0.24,0.219 10 0.1 2.281,1.323 2.531,1.542 0.25,0.219 10 20 2.542,3.823 2.781,4.042 0.24,0.219 10 -20 2.938,3.823 3.177,4.042 0.24,0.219 10 0 3.208,3.823 3.448,4.042 0.24,0.219 10 20 3.521,3.823 3.76,4.042 0.24,0.219 10 40 3.833,3.823 4.073,4.042 0.24,0.219 10 60 4.146,3.823 4.385,4.042 0.24,0.219 10 80 4.385,3.823 4.625,4.042 0.24,0.219 10 100 2.583,4 2.823,4.219 0.24,0.219 10 -4 2.896,4 3.135,4.219 0.24,0.219 10 32 3.208,4 3.448,4.219 0.24,0.219 10 68 3.479,4 3.729,4.25 0.25,0.25 10 104 3.792,4 4.125,4.25 0.333,0.25 10 140 4.094,4 4.417,4.25 0.323,0.25 10 176 4.385,4 4.708,4.25 0.323,0.25 10 212 4.677,3.823 5,4.073 0.323,0.25 10 (°C) 4.677,4 5,4.25 0.323,0.25 10 (°F) 3.802,1.896 4.583,2.167 0.781,0.271 10 Acceptable 2.26,0.719 3.083,0.917 0.823,0.198 10 Resistance 2.24,3.021 2.479,3.24 0.24,0.219 10 0.3

The intake air temperature sensor, mounted on the intake air flow meter assembly, monitors the intake air temperature. The intake air temperature sensor has a built-in thermistor with a resistance that varies according to the temperature of the intake air. When the intake air temperature is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are transmitted to the ECM as voltage changes (See Fig. 1).

The intake air temperature sensor is powered by a 5 V supply from the THA terminal of the ECM, via resistor R.

Resistor R and the intake air temperature sensor are connected in series. When the resistance value of the intake air temperature sensor changes, according to changes in the intake air temperature, the voltage at terminal THA also varies. Based on this signal, the ECM increases the fuel injection volume when the engine is cold to improve driveability.

HINT:

When DTC P0112 or P0113 is stored, the ECM enters fail-safe mode. During fail-safe mode, the intake air temperature is estimated to be 20°C (68°F) by the ECM. Fail-safe mode continues until a pass condition is detected.



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0112 Intake Air Temperature Sensor System Open/Low A short in the intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Short in intake air temperature sensor circuit

·

Intake air temperature sensor (built into mass air flow meter sub-assembly)

·

ECM


Comes on DTC stored
P0113 Intake Air Temperature Sensor System Open/High An open in the intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Open in intake air temperature sensor circuit

·

Intake air temperature sensor (built into mass air flow meter sub-assembly)

·

ECM


Comes on DTC stored

HINT:

When any of these DTCs are output, check the intake air temperature using the GTS or Techstream. Enter the following menus: Powertrain / EFI / Data List / Intake air temperature.

Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) Short circuit


CONFIRMATION DRIVING PATTERN

1.

Connect the GTS or Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS or Techstream on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS or Techstream on.

6.

Wait 5 seconds or more.

7.

Enter the following menus: Powertrain / EFI / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, the system is normal.




WIRING DIAGRAM

A360382E07
0.51,2.698 0.969,2.896 0.458,0.198 10 false C41 0.521,2.865 2.99,3.271 2.469,0.406 10 false Intake Air Temperature Sensor (Built into Intake Air Flow Meter Assembly) 1.875,1.354 2.333,1.552 0.458,0.198 10 false THA 2.073,1.969 2.229,2.167 0.156,0.198 10 false - 2.24,1.344 2.396,1.542 0.156,0.198 10 false 1 2.25,1.948 2.406,2.146 0.156,0.198 10 false 2 5.313,1.354 5.771,1.552 0.458,0.198 10 false THA 5.052,1.354 5.365,1.552 0.313,0.198 10 false 74 5.323,1.948 5.635,2.146 0.313,0.198 10 false E2 4.99,1.948 5.448,2.146 0.458,0.198 10 false 100 5.979,0.938 6.292,1.135 0.313,0.198 10 false 5V 5.99,1.219 6.146,1.417 0.156,0.198 10 false R 5.49,3 5.948,3.198 0.458,0.198 10 false C50 5.844,3 6.302,3.198 0.458,0.198 10 false ECM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS or Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS OR TECHSTREAM (INTAKE AIR TEMPERATURE)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Powertrain / EFI / Data List / Intake air temperature.


e.

Read the value displayed on the GTS or Techstream.

OK:

Same as actual intake air temperature.


HINT:
·

If there is an open circuit, the GTS or Techstream indicates -40°C (-40°F).

·

If there is a short circuit, the GTS or Techstream indicates 140°C (284°F).




Result:
Result Proceed to
-40°C (-40°F) A
140°C (284°F) B
Same as actual intake air temperature C



A

2.READ VALUE USING GTS OR TECHSTREAM (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING GTS OR TECHSTREAM (CHECK FOR SHORT IN WIRE HARNESS)

C

2.READ VALUE USING GTS OR TECHSTREAM (CHECK FOR OPEN IN WIRE HARNESS)
a.

Disconnect the intake air flow meter assembly connector.

A194099C71
6.167,1.688 6.521,1.906 0.354,0.219 5.073,1.896 4.75,2.302 true 5.177,1.906 5.094,2.292 true 1.292,2.042 1.479,2.229 0.188,0.188 10 false *1 4.302,0.333 4.5,0.531 0.198,0.198 10 false *a 2.802,2.042 3.01,2.229 0.208,0.188 10 false *2 2.292,1.156 3.094,1.479 0.802,0.323 10 false THA 4.573,2.302 4.896,2.469 0.323,0.167 10 false THA 5.063,2.302 5.344,2.469 0.281,0.167 10 false - 2.302,1.458 3.24,1.667 0.938,0.208 10 false E2 6.219,1.719 6.667,1.969 0.448,0.25 10 false C41
*1 Intake Air Flow Meter Assembly *2 ECM
*a Front view of wire harness connector
(to Intake Air Flow Meter Assembly)
- -



b.

Connect terminals 1 (THA) and 2 (-) of the intake air flow meter assembly connector on the wire harness side.


c.

Connect the GTS or Techstream to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS or Techstream on.


f.

Enter the following menus: Powertrain / EFI / Data List / Intake air temperature.


g.

Read the value displayed on the GTS or Techstream.

Standard value:

140°C (284°F) or more.



Result:
Proceed to
OK
NG



OK

REPLACE INTAKE AIR FLOW METER ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (INTAKE AIR FLOW METER ASSEMBLY - ECM)
3.CHECK HARNESS AND CONNECTOR (INTAKE AIR FLOW METER ASSEMBLY - ECM)
a.

Disconnect the intake air flow meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C41-1 (THA) - C50-74 (THA) Always Below 1 Ω
C41-2 (-) - C50-100 (E2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING GTS OR TECHSTREAM (CHECK FOR SHORT IN WIRE HARNESS)
a.
A280726C03
0.729,0.281 1.063,0.521 0.333,0.24 10 false *1 2.604,0.281 3.021,0.615 0.417,0.333 10 false *2 2.51,1.031 2.865,1.25 0.354,0.219 10 false THW 2.49,1.531 2.969,1.771 0.479,0.24 10 false E2
*1 Intake Air Flow Meter Assembly
*2 ECM


Disconnect the intake air flow meter assembly connector.


b.

Connect the GTS or Techstream to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS or Techstream on.


e.

Enter the following menus: Powertrain / EFI / Data List / Intake air temperature.


f.

Read the value displayed on the GTS or Techstream.

Standard value:

-40°C (-40°F) or less.



Result:
Proceed to
OK
NG



OK

REPLACE INTAKE AIR FLOW METER ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (INTAKE AIR FLOW METER ASSEMBLY - ECM)
5.CHECK HARNESS AND CONNECTOR (INTAKE AIR FLOW METER ASSEMBLY - ECM)
a.

Disconnect the intake air flow meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C41-1 (THA) or C50-74 (THA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR