A thermistor, whose resistance value varies according to the engine coolant temperature, is built into the engine coolant temperature sensor. The structure of the sensor and its connection to the ECM are the same as those of the intake air temperature sensor.
When DTC P0115, P0117 or P0118 is stored, the ECM enters fail-safe mode. During fail-safe mode, the engine coolant temperature is estimated to be 80°C (176°F) by the ECM. Fail-safe mode continues until a pass condition is detected.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0115 | Engine Coolant Temperature Sensor System Open | An open or short in the engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic). | ·
Open or short in engine coolant temperature sensor circuit ·
Engine coolant temperature sensor ·
ECM |
Comes on | DTC stored |
| P0117 | Engine Coolant Temperature Sensor System Open/Low | A short in the engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic). | ·
Short in engine coolant temperature sensor circuit ·
Engine coolant temperature sensor ·
ECM |
Comes on | DTC stored |
| P0118 | Engine Coolant Temperature Sensor System Open/High | An open in the engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic). | ·
Open in engine coolant temperature sensor circuit ·
Engine coolant temperature sensor ·
ECM |
Comes on | DTC stored |
When any of these DTCs are output, check the engine coolant temperature using the GTS or Techstream. Enter the following menus: Powertrain / EFI / Data List / Engine coolant temperature.
| Temperature Displayed | Malfunction |
|---|---|
| -40°C (-40°F) | Open circuit |
| 140°C (284°F) | Short circuit |
Connect the GTS or Techstream to the DLC3.
Turn the ignition switch to ON and turn the GTS or Techstream on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS or Techstream on.
Wait 5 seconds or more.
Enter the following menus: Powertrain / EFI / Trouble Codes.
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, the system is normal.
Read freeze frame data using the GTS or Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
If DTC P0117 is stored, check that the engine does not overheat (the DTC P0117 may be stored due to engine overheating).
Connect the GTS or Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the GTS or Techstream on.
Enter the following menus: Powertrain / EFI / Data List / Engine coolant temperature.
Read the value displayed on the GTS or Techstream.
Between 75 and 100°C (167 and 212°F) with warm engine.
If there is an open circuit, the GTS or Techstream indicates -40°C (-40°F).
If there is a short circuit, the GTS or Techstream indicates 140°C (284°F).
| Result | Proceed to |
|---|---|
| -40°C (-40°F) | A |
| 140°C (284°F) | B |
| Between 75 and 100°C (167 and 212°F) | C |
A
B
C
Disconnect the engine coolant temperature sensor connector.
| *1 | Engine Coolant Temperature Sensor | *2 | ECM |
| *a | Front view of wire harness connector
(to Engine Coolant Temperature Sensor) |
- | - |
Connect terminals 1 and 2 of the engine coolant temperature sensor connector on the wire harness side.
Connect the GTS or Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the GTS or Techstream on.
Enter the following menus: Powertrain / EFI / Data List / Engine coolant temperature.
Read the value displayed on the GTS or Techstream.
140°C (284°F) or more
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the engine coolant temperature sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C54-2 - C50-32 (THW) | Always | Below 1 Ω |
| C54-1 - C50-100 (E2) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Engine Coolant Temperature Sensor |
| *2 | ECM |
Disconnect the engine coolant temperature sensor connector.
Connect the GTS or Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the GTS or Techstream on.
Enter the following menus: Powertrain / EFI / Data List / Engine coolant temperature.
Read the value displayed on the GTS or Techstream.
-40°C (-40°F) or less.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the engine coolant temperature sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C54-2 or C50-32 (THW) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG