A flat type knock control sensor (non-resonant type) has a structure that can detect vibrations between approximately 5 kHz and 15 kHz.
The knock control sensor is fitted onto the engine block to detect engine knocking.
The knock control sensor contains a piezoelectric element which generates a voltage when it becomes deformed.
The voltage is generated when the engine block vibrates due to knocking. Any occurrence of engine knocking can be suppressed by delaying the ignition timing.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0327 | Knock Sensor System Open/Low | The output voltage of the knock control sensor is less than 0.5 V for 1 second or more (1 trip detection logic). | ·
Short in knock control sensor circuit ·
Knock control sensor ·
ECM |
Comes on | DTC stored |
| P0328 | Knock Sensor System Open/High | The output voltage of the knock control sensor is higher than 4.5 V for 1 second or more (1 trip detection logic). | ·
Open in knock control sensor circuit ·
Knock control sensor ·
ECM |
Comes on | DTC stored |
When DTC P0327 or P0328 is stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is delayed to its maximum retardation. Fail-safe mode continues until the ignition switch is turned off.
Reference: Inspection using an oscilloscope
The correct waveform is as shown.
| ECM Terminal Name | Between KNK and E2 |
| Tester Range | 1 V/DIV., 1 ms./DIV. |
| Condition | Engine speed maintained at 4000 rpm after warming up engine |
Connect the GTS or Techstream to the DLC3.
Turn the ignition switch to ON and turn the GTS or Techstream on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS or Techstream on.
Start the engine and wait 5 minutes.
Enter the following menus: Powertrain / EFI / Trouble Codes.
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, the system is normal.
Read freeze frame data using the GTS or Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the GTS or Techstream to the DLC3.
Start the engine.
Turn the GTS or Techstream on.
Warm up the engine.
Enter the following menus: Powertrain / EFI / Data List / Knock control value.
Read the value while driving the vehicle.
The value changes.
| Malfunction does not occur | Knock control value changes |
| Malfunctions occur | Knock control value does not change |
The Knock control value change can be confirmed by running the engine with a high load, for example, by activating the air conditioning system and racing the engine.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Knock Control Sensor) |
Disconnect the knock control sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C13-2(+) - C13-1(-) | Ignition switch ON | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the knock control sensor.
Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>KNOCK SENSOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the knock control sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C13-2(+) - C50-106 (KNK) | Always | Below 1 Ω |
| C13-1(-) - C50-100 (E2) | Always | Below 1 Ω |
| C13-2(+) or C50-106 (KNK) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG