Home › Engine / Hybrid System › 2NR-VE ENGINE CONTROL › SFI SYSTEM(w/ Air Fuel Ratio Sensor) › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042272 2NR-VE ENGINE CONTROL _0196262 SFI SYSTEM(w/ Air Fuel Ratio Sensor) C

2NR-VE ENGINE CONTROL  SFI SYSTEM(w/ Air Fuel Ratio Sensor)  P1603  Engine Stall  


DESCRIPTION

When the engine stalls after starting, DTC is output. To grasp the situation when DTC is output, the freeze frame data can be checked by using the GTS or Techstream. Because the engine running conditions when it stalls can be checked by using the freeze frame data, vehicle maintenance services can improve. Moreover, because an engine stall due to lack of fuel is also detected, the fuel must be checked before operation. (An engine stall may be detected due to cranking, even if the engine does not stall.)

DTC No. Detection Item DTC Detection Condition MIL Memory
P1603 Engine Stall After monitoring for startability problems (P1604) finishes and 5 seconds or more elapse after starting the engine, with the engine running, the engine stops without the ignition switch being operated.
(1 trip detection logic)
- DTC stored

CAUTION / NOTICE / HINT

HINT:
·

When other DTCs are displayed, first troubleshoot the corresponding DTC.

·

Because DTC P1603 differs from the conventional DTC, the following procedure is described as an example.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P1603)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Powertrain / EFI / Trouble Codes.


e.

Read DTCs.


Result:
Result Proceed to
DTC P1603 is output A
DTC P1603 and other DTCs are output B



A

2.CHECK FREEZE FRAME DATA

B

2.CHECK FREEZE FRAME DATA
HINT:

Using the time series freeze frame data, check the data when and after the DTC is detected, to be used for troubleshooting.


a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Check the time series freeze frame data following the instructions displayed on the GTS or Techstream, and check the vehicle conditions when the engine stalls.

Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>SFI SYSTEM(w/ Air Fuel Ratio Sensor)>FREEZE FRAME DATA


e.

Check the freeze frame data data whether the engine was cool or warmed up.

Tester Display
Engine coolant temperature ECT at engine start


f.

Using the freeze frame data, check whether the engine was idling, running at a constant speed, decelerating, accelerating, starting and stopping.

Tester Display
Engine revolution speed Sub throttle sensor voltage
Vehicle Speed ISC opening angle
Relative throttle position Stop lamp SW
Main throttle sensor voltage ST1 input flag


g.

Check the feedback performance state.

Tester Display
Short term fuel trim bank 1 O2S B1S1
Long term fuel trim bank 1 -


h.

Check the freeze frame data of the engine load/electric load.

Tester Display
Calculated load value Electric load signal 3
Electric load signal 1 A/C magnet clutch relay test
Electric load signal 2 Engine oil pressure SW


i.

Check the freeze frame data of the fuel injection.

Tester Display
Injection volume Injection time


j.

Referring to the above freeze frame data, perform the reproduction test.


k.

Based on the freeze frame data and the reproduction test, specify the malfunctioning section while comparing to the reference values shown in the ECM data list description

Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>SFI SYSTEM(w/ Air Fuel Ratio Sensor)>DATA LIST / ACTIVE TEST


Result:
Result Proceed to
The malfunctioning section can be specified A
The malfunctioning section can not be specified B



A

CHECK AND REPAIR LOCATION WHERE MALFUNCTION EXIST

B