Home › Engine / Hybrid System › 2NR-VE ENGINE CONTROL › SFI SYSTEM(w/ Air Fuel Ratio Sensor) › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042272 2NR-VE ENGINE CONTROL _0196262 SFI SYSTEM(w/ Air Fuel Ratio Sensor) C

2NR-VE ENGINE CONTROL  SFI SYSTEM(w/ Air Fuel Ratio Sensor)  P2109  Throttle Flow Decrease Malfunction  


DESCRIPTION

The idle speed is controlled by the Electronic Throttle Control System (ETCS). The ETCS is comprised of a throttle actuator, which operates the throttle valve, and a throttle position sensor, which detects the opening amount of the throttle valve. The ECM controls the throttle actuator to adjust the throttle valve opening amount so that the idle speed is maintained at the target idle speed.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2109 Throttle Flow Decrease Malfunction The Throttle barometric correction* is approximately 3 times larger than normal even though the actual intake air amount during idle is within the normal range (up to 1.5 times the normal amount) (5 trip detection logic).
*: Data List item
Throttle body with motor assembly Does not come on DTC stored

HINT:
·

The Throttle barometric correction is the calculated intake air amount corresponding to the throttle opening amount necessary to maintain the idle speed.

·

This malfunction is only detected once per trip. After it has been detected once, the system will not monitor for the malfunction for the rest of the trip.

·

The system uses the throttle body with motor assembly and mass air flow meter sub-assembly to detect this malfunction.



CAUTION / NOTICE / HINT

HINT:
·

Since a pending DTC is not stored for this DTC, it takes time to confirm whether the malfunction has been successfully repaired by checking for this DTC. When confirming whether the malfunction has been successfully repaired, compare "Throttle barometric correction" recorded in the freeze frame data with "Throttle barometric correction" in the Data List after repairs have been made to save time.

·

Read freeze frame data using the GTS or Techstream. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2109)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Powertrain / EFI / Trouble Codes.


e.

Read the DTCs.

HINT:

If any DTCs other than P2109 are output, troubleshoot those DTCs first.



Result:
Result Proceed to
DTC P2109 is output A
DTC P2109 and other DTCs are output B



A

2.READ FREEZE FRAME DATA

B

2.READ FREEZE FRAME DATA
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Using the GTS or Techstream, check "Throttle barometric correction" in the freeze frame data.

Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>SFI SYSTEM(w/ Air Fuel Ratio Sensor)>FREEZE FRAME DATA

HINT:

Be sure to confirm "Throttle barometric correction" in the freeze frame data as it is used when confirming whether the malfunction has been successfully repaired.



Result:
Proceed to
NEXT



NEXT

3.REMOVE FOREIGN MATTER (CLEAN THROTTLE BODY WITH MOTOR ASSEMBLY)
3.REMOVE FOREIGN MATTER (CLEAN THROTTLE BODY WITH MOTOR ASSEMBLY)
a.

Clean off any deposits from the inside of the throttle body with motor assembly.

A213929C10
1.958,1.323 2.354,1.594 true 1.969,1.146 2.354,1.146 true 0.781,2.479 1.229,2.375 true 1.729,3.625 1.521,3.073 true 1.031,0.573 1.604,0.688 true 0.771,3.073 1.385,2.729 true 0.271,0.344 0.583,0.5 0.313,0.156 10 false *1 0.854,0.51 1.167,0.667 0.313,0.156 10 false *2 2.406,1.542 2.656,1.823 0.25,0.281 10 false *e 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 1.688,0.177 2,0.333 0.313,0.156 10 false *b 1.688,1.927 2,2.083 0.313,0.156 10 false *c 4.771,0.917 5.083,1.073 0.313,0.156 10 false *d 0.583,2.417 0.896,2.573 0.313,0.156 10 false *2 1.667,3.625 2,3.802 0.333,0.177 10 false *e 0.594,3.031 0.906,3.188 0.313,0.156 10 false *3 2.385,1.083 2.698,1.24 0.313,0.156 10 false *3
*1 Throttle Body with Motor Assembly *2 Bore
*3 Valve - -
*a Reference *b Throttle Body with Motor Assembly Cross-section Diagram
*c When valve fully opened *d Do not directly apply cleaner
*e Deposits - -


i.

Push open the throttle valve and wipe off any carbon from the valve and bore using a cloth soaked in non-residue solvent.

NOTICE:
·

Make sure that the cloth or your fingers do not get caught in the valve.

·

Make sure that foreign matter does not enter the throttle valve.

·

Do not directly apply non-residue solvent to the throttle body with motor assembly or wash the throttle body with motor assembly. Cleaning solvent may leak into the motor from the shaft and cause problems such as rust or valve movement problems.

·

If there is coating material on the edge of the valve, be careful not to remove it.

·

Push the throttle valve open gently with your finger and check that the throttle valve moves smoothly.



HINT:

If the throttle valve does not open smoothly, replace the throttle body with motor assembly.




Result:
Proceed to
NEXT



NEXT

4.READ VALUE USING GTS OR TECHSTREAM (THROTTLE BAROMETRIC CORRECTION)
4.READ VALUE USING GTS OR TECHSTREAM (THROTTLE BAROMETRIC CORRECTION)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Powertrain / EFI / Data List / Throttle barometric correction.


e.

Read the value.

OK:

The value is half of "Throttle barometric correction" recorded in the freeze frame data or less.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY