Home › Engine / Hybrid System › 2NR-VE ENGINE CONTROL › SFI SYSTEM(w/ Air Fuel Ratio Sensor) › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042272 2NR-VE ENGINE CONTROL _0196262 SFI SYSTEM(w/ Air Fuel Ratio Sensor) C

2NR-VE ENGINE CONTROL  SFI SYSTEM(w/ Air Fuel Ratio Sensor)  P2120  Accelerator Pedal Position Sensor (Main) Open  P2122  Accelerator Pedal Position Sensor (Main) Open/Low  P2123  Accelerator Pedal Position Sensor (Main) Open/High  P2125  Accelerator Pedal Position Sensor (Sub) Open  P2127  Accelerator Pedal Position Sensor (Sub) Open/Low  P2128  Accelerator Pedal Position Sensor (Sub) Open/High  P2138  Accelerator Pedal Position Sensor Main/Sub Voltage Correlation  


DESCRIPTION

HINT:
·

This Electronic Throttle Control System (ETCS) does not use a throttle cable.

·

These DTCs relate to the accelerator pedal position sensor.



The accelerator pedal position sensor is built into the accelerator pedal sensor assembly and has 2 sensor circuits: VPA (main) and VPA2 (sub). This sensor is a non-contact type sensor and uses Hall-effect elements in order to yield accurate signals even in extreme driving conditions, such as at high speeds as well as very low speeds. The voltage, which is applied to terminals VPA and VPA2 of the ECM, varies between 0.5 V and 4.75 V in proportion to the operating angle of the accelerator pedal (throttle valve). A signal from VPA indicates the actual accelerator pedal opening angle (throttle valve opening angle) and is used for engine control. A signal from VPA2 conveys the status of the VPA circuit and is used to check the accelerator pedal position sensor itself.

The ECM monitors the actual accelerator pedal opening angle (throttle valve opening angle) through the signals from VPA and VPA2, and controls the throttle actuator according to these signals.

A255815E43
4.333,2.031 4.208,1.948 false 4.323,2.198 4.208,2.146 false 4.344,2.24 4.229,2.333 false 4.344,2.396 4.229,2.51 false 4.344,2.917 4.219,2.917 false 4.354,3.125 4.208,3.125 false 0.844,2.875 0.552,3.281 false 1.063,2.198 1.323,1.365 false 4.333,1.833 3.844,0.938 false 1.323,1.365 1.417,1.365 false 1.063,2.563 0.927,1.823 false 0.927,1.823 0.854,1.823 false 0.552,3.802 1.708,4.135 1.156,0.333 10 false Accelerator Pedal Position Sensor 1.458,1.292 1.938,1.469 0.479,0.177 10 false Magnet 0.313,1.74 0.844,1.917 0.531,0.177 10 false IC No. 1 0.313,3.313 0.844,3.49 0.531,0.177 10 false IC No. 2 2.063,1.74 2.531,1.917 0.469,0.177 10 false VPA1 2.063,2.073 2.552,2.271 0.49,0.198 10 false EP1 2.063,2.385 2.583,2.563 0.521,0.177 10 false VCP1 2.063,2.688 2.573,2.865 0.51,0.177 10 false VPA2 2.063,3 2.563,3.198 0.5,0.198 10 false EP2 2.052,3.323 2.573,3.5 0.521,0.177 10 false VCP2 2.677,3.76 3,3.938 0.323,0.177 10 false ECM 4.271,1.542 4.427,1.719 0.156,0.177 10 false *1 5.865,1.542 6.021,1.719 0.156,0.177 10 false *2 3.917,1.854 4.208,2.031 0.292,0.177 10 false 4.55 3.844,2.063 4.208,2.24 0.365,0.177 10 false 3.988 3.938,2.281 4.229,2.458 0.292,0.177 10 false 3.75 3.875,2.469 4.24,2.646 0.365,0.177 10 false 3.188 3.969,2.823 4.271,3 0.302,0.177 10 false 1.6 3.979,3.042 4.281,3.219 0.302,0.177 10 false 0.8 4.406,3.344 4.698,3.521 0.292,0.177 10 false 0.29 4.26,3.594 4.417,3.771 0.156,0.177 10 false 0 5.781,3.594 6.073,3.771 0.292,0.177 10 false 15.9 4.677,3.583 5.604,3.823 0.927,0.24 10 false Usable Range 4.667,3.896 7.167,4.094 2.5,0.198 10 false Accelerator Pedal Angle (°) 4.344,4.656 6.625,4.833 2.281,0.177 10 false *1: Accelerator Pedal Fully Released 4.344,4.969 6.729,5.135 2.385,0.167 10 false *2: Accelerator Pedal Fully Depressed 2.156,0.813 3.854,1.167 1.698,0.354 10 false Accelerator Pedal Position Sensor Output Voltage (V) 6.479,2.281 6.927,2.51 0.448,0.229 10 false VPA 6.438,1.823 6.865,2 0.427,0.177 10 false VPA2

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2120 Accelerator Pedal Position Sensor (Main) Open VPA fluctuates rapidly beyond the upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic).
·

Accelerator pedal sensor assembly

·

Open or short in accelerator pedal sensor assembly circuit

·

ECM


Comes on DTC stored
P2122 Accelerator Pedal Position Sensor (Main) Open/Low VPA is 0.4 V or less for 0.5 seconds or more when the accelerator pedal is depressed (1 trip detection logic).
·

Accelerator pedal sensor assembly

·

Open in VCPA circuit

·

Open or ground short in VPA circuit

·

ECM


Comes on DTC stored
P2123 Accelerator Pedal Position Sensor (Main) Open/High VPA is 4.8 V or higher for 2 seconds or more (1 trip detection logic).
·

Accelerator pedal sensor assembly

·

Open in EPA circuit

·

Short in VPA circuit

·

ECM


Comes on DTC stored
P2125 Accelerator Pedal Position Sensor (Sub) Open VPA2 fluctuates rapidly beyond the upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic).
·

Accelerator pedal sensor assembly

·

Open or short in accelerator pedal sensor assembly circuit

·

ECM


Comes on DTC stored
P2127 Accelerator Pedal Position Sensor (Sub) Open/Low VPA2 is 1.2 V or less for 0.5 seconds or more when the accelerator pedal is depressed (1 trip detection logic).
·

Accelerator pedal sensor assembly

·

Open in VCP2 circuit

·

Open or ground short in VPA2 circuit

·

ECM


Comes on DTC stored
P2128 Accelerator Pedal Position Sensor (Sub) Open/High Both of the following conditions are met for 2 seconds or more (1 trip detection logic):
(a) VPA2 is 4.8 V or higher.
(b) VPA is between 0.4 V and 3.45 V.
·

Accelerator pedal sensor assembly

·

Open in EPA2 circuit

·

Short in VPA2 circuit

·

ECM


Comes on DTC stored
P2138 Accelerator Pedal Position Sensor Main/Sub Voltage Correlation Either of the following conditions is met for 2 seconds or more (1 trip detection logic):
(a) The difference between VPA and VPA2 is 0.02 V or less.
(b) VPA is 0.4 V or less, and VPA2 is 1.2 V or less.
·

Short between VPA and VPA2 circuits

·

Accelerator pedal sensor assembly

·

ECM


Comes on DTC stored

HINT:

When any of these DTCs are output, check the accelerator pedal position sensor voltage using the GTS or Techstream. Enter the following menus: Powertrain / EFI / Data List / Main accelerator sensor voltage and Sub accelerator sensor voltage.

Trouble Area Accelerator Pedal Fully Released Accelerator Pedal Fully Depressed
Main accelerator sensor voltage Sub accelerator sensor voltage Main accelerator sensor voltage Sub accelerator sensor voltage
Open in VCP circuit 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V
Open or ground short in VPA circuit 0 to 0.2 V 1.2 to 2.0 V 0 to 0.2 V 3.4 to 4.75 V
Open or ground short in VPA2 circuit 0.5 to 1.1 V 0 to 0.2 V 2.6 to 4.5 V 0 to 0.2 V
Open in EPA circuit 4.5 to 4.98 V 4.5 to 4.98 V 4.5 to 4.98 V 4.5 to 4.98 V
Normal condition 0.5 to 1.1 V 1.2 to 2.0 V 2.6 to 4.5 V 3.4 to 4.75 V


HINT:

Accelerator pedal positions are expressed as voltages.


COMPONENT OPERATING RANGE

All of the following conditions are met -
VPA voltage Higher than 0.4 V, and less than 4.8 V
VPA2 voltage Higher than 1.2 V, and less than 4.8 V
Difference between VPA and VPA2 voltages Higher than 0.02 V

CONFIRMATION DRIVING PATTERN

A199317E37
3.635,2.01 2.771,1.302 2.771,1.302 2.927,1.302 false 4.74,2.448 5.115,1.781 5.115,1.781 5.26,1.781 false 2.208,2.438 2.438,2.073 2.438,2.073 2.542,2.073 false 0.125,0.094 1.74,0.271 1.615,0.177 10 Accelerator Pedal State 0.865,0.417 1.583,0.563 0.719,0.146 10 Depressed 0.948,0.875 1.594,1.031 0.646,0.156 10 Released 0.427,2.406 1.635,2.573 1.208,0.167 10 Ignition Switch ON 2.094,2.49 2.323,2.688 0.229,0.198 10 [A] 4.406,3.427 4.646,3.615 0.24,0.188 10 [C] 5.344,1.698 5.99,1.854 0.646,0.156 10 Released 2.875,3.052 3.573,3.24 0.698,0.188 10 5 seconds 2.99,1.229 3.729,1.427 0.74,0.198 10 Depressed 3.885,1.125 4.125,1.333 0.24,0.208 10 [B] 2.594,2.01 3.24,2.167 0.646,0.156 10 Released

1.

Connect the GTS or Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS or Techstream on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS or Techstream on [A].

6.

Fully depress and release the accelerator pedal [B].

7.

Check that 5 seconds or more have elapsed since the ignition switch to ON.

8.

Enter the following menus: Powertrain / EFI / Trouble Codes [C].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, the system is normal.




FAIL-SAFE

When DTC P2120, P2121, P2122, P2123, P2125, P2127, P2128 or P2138 is stored, the ECM enters fail-safe mode. If either of the 2 sensor circuits malfunctions, the ECM limits the engine output. If both of the circuits malfunction, the ECM regards the accelerator pedal as being released. As a result, the throttle valve is closed and the engine idles.

Fail-safe mode continues until a pass condition is detected, and the ignition switch is turned off.

WIRING DIAGRAM

A255383E87
2,0.531 2.094,0.677 0.094,0.146 10 false 6 1.521,0.635 2.104,0.896 0.583,0.26 10 false VPA1 2,0.958 2.094,1.104 0.094,0.146 10 false 5 1.583,1.042 2.156,1.292 0.573,0.25 10 false EP1 2,1.375 2.094,1.521 0.094,0.146 10 false 4 1.479,1.458 1.875,1.604 0.396,0.146 10 false VCP1 2,1.802 2.094,1.948 0.094,0.146 10 false 3 1.5,1.885 1.875,2.031 0.375,0.146 10 false VPA2 2,2.219 2.094,2.365 0.094,0.146 10 false 2 1.573,2.313 1.948,2.458 0.375,0.146 10 false EP2 2,2.635 2.094,2.781 0.094,0.146 10 false 1 1.5,2.719 1.885,2.865 0.385,0.146 10 false VCP2 5.344,0.542 5.531,0.729 0.188,0.188 10 false 44 5.604,0.51 6.094,0.771 0.49,0.26 10 false VPA 5.344,0.958 5.552,1.156 0.208,0.198 10 false 58 5.604,1.156 6.146,1.396 0.542,0.24 10 false EPA 5.344,1.375 5.615,1.625 0.271,0.25 10 false 30 5.604,1.375 6,1.521 0.396,0.146 10 false VCP1 5.344,1.802 5.604,2 0.26,0.198 10 false 45 5.604,1.771 5.979,1.917 0.375,0.146 10 false VPA2 5.344,2.219 5.604,2.438 0.26,0.219 10 false 59 5.604,2.396 5.979,2.542 0.375,0.146 10 false EPA2 5.344,2.635 5.542,2.854 0.198,0.219 10 false 31 5.604,2.635 5.99,2.781 0.385,0.146 10 false VCP2 0.073,3.135 0.49,3.49 0.417,0.354 10 false A23*1 0.531,3.146 2.99,3.771 2.458,0.625 10 false Accelerator Pedal Position Sensor (Accelerator Pedal Sensor Assembly) 5.792,3.146 6.198,3.375 0.406,0.229 10 false A24 6.115,3.146 6.438,3.292 0.323,0.146 10 false ECM 6.333,1.25 6.604,1.479 0.271,0.229 10 false 5 V 6.333,2.5 6.604,2.729 0.271,0.229 10 false 5 V 0.073,3.323 0.49,3.677 0.417,0.354 10 false E88*2 3.198,3.333 4.031,3.688 0.833,0.354 10 false *1: for RHD 4.083,3.333 4.917,3.688 0.833,0.354 10 false *2: for LHD

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS or Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS OR TECHSTREAM (ACCEL SENSOR OUT)
A208621C05
0.719,1.75 1,1.969 0.281,0.219 10 *a 2.646,1.74 2.927,1.979 0.281,0.24 10 *b
*a Fully Depressed
*b Fully Released


a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Powertrain / EFI / Data List / Main accelerator sensor voltage and Sub accelerator sensor voltage.


e.

Read the value displayed on the GTS or Techstream.

Standard Voltage:
Accelerator Pedal Operation Main accelerator sensor voltage Sub accelerator sensor voltage Difference between Main accelerator sensor voltage and Sub accelerator sensor voltage
Fully Released 0.5 to 1.1 V 1.2 to 2.0 V Higher than 0.02 V
Fully Depressed 2.6 to 4.5 V 3.4 to 4.75 V



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL SENSOR ASSEMBLY - ECM)
2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL SENSOR ASSEMBLY - ECM)
a.

Disconnect the accelerator pedal sensor assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

i.

for RHD

Standard Resistance:
Tester Connection Condition Specified Condition
A23-6 (VPA1) - A24-44 (VPA) Always Below 1 Ω
A23-5 (EP1) - A24-58 (EPA) Always Below 1 Ω
A23-4 (VCP1) - A24-30 (VCP1) Always Below 1 Ω
A23-3 (VPA2) - A24-45 (VPA2) Always Below 1 Ω
A23-2 (EP2) - A24-59 (EPA2) Always Below 1 Ω
A23-1 (VCP2) - A24-31 (VCP2) Always Below 1 Ω
A23-6 (VPA1) or A24-44 (VPA) - Body ground and other terminals Always 10 kΩ or higher
A23-4 (VCP1) or A24-30 (VCP1) - Body ground and other terminals Always 10 kΩ or higher
A23-3 (VPA2) or A24-45 (VPA2) - Body ground and other terminals Always 10 kΩ or higher
A23-1 (VCP2) or A24-31 (VCP2) - Body ground and other terminals Always 10 kΩ or higher



ii.

for LHD

Standard Resistance:
Tester Connection Condition Specified Condition
E88-6 (VPA1) - A24-44 (VPA) Always Below 1 Ω
E88-5 (EP1) - A24-58 (EPA) Always Below 1 Ω
E88-4 (VCP1) - A24-30 (VCP1) Always Below 1 Ω
E88-3 (VPA2) - A24-45 (VPA2) Always Below 1 Ω
E88-2 (EP2) - A24-59 (EPA2) Always Below 1 Ω
E88-1 (VCP2) - A24-31 (VCP2) Always Below 1 Ω
E88-6 (VPA1) or A24-44 (VPA) - Body ground and other terminals Always 10 kΩ or higher
E88-4 (VCP1) or A24-30 (VCP1) - Body ground and other terminals Always 10 kΩ or higher
E88-3 (VPA2) or A24-45 (VPA2) - Body ground and other terminals Always 10 kΩ or higher
E88-1 (VCP2) or A24-31 (VCP2) - Body ground and other terminals Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ACCELERATOR PEDAL SENSOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ACCELERATOR PEDAL SENSOR ASSEMBLY)
A259467C15
0.333,1.833 0.75,2.083 0.417,0.25 0.333,1.417 0.75,1.667 0.417,0.25 1,2.823 1.438,2.177 true 1.302,2.177 0.792,2.563 true 2.031,2.833 1.844,2.198 true 1.719,2.208 1.583,2.833 true 0.219,0.188 0.76,0.552 0.542,0.365 10 false *a 0.417,1.885 0.833,2.083 0.417,0.198 10 false E88 1.938,2.854 2.313,3.031 0.375,0.177 10 false EP1 0.833,2.844 1.396,3.021 0.563,0.177 10 false EP2 0.292,2.49 0.698,2.656 0.406,0.167 10 false VCP2 1.354,2.844 1.885,3.052 0.531,0.208 10 false VCP1 0.417,1.469 0.833,1.667 0.417,0.198 10 false A23 0.125,1.458 0.667,1.823 0.542,0.365 10 false *A 0.125,1.885 0.667,2.25 0.542,0.365 10 false *B
*A for RHD
*B for LHD
*a Front view of wire harness connector
(to Accelerator Pedal Sensor Assembly)


a.

Disconnect the accelerator pedal sensor assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

i.

for RHD

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A23-4 (VCP1) - A23-5 (EP1) Ignition switch ON 4.5 to 5.5 V
A23-1 (VCP2) - A23-2 (EP2) Ignition switch ON 4.5 to 5.5 V



ii.

for LHD

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E88-4 (VCP1) - E88-5 (EP1) Ignition switch ON 4.5 to 5.5 V
E88-1 (VCP2) - E88-2 (EP2) Ignition switch ON 4.5 to 5.5 V




Result:
Proceed to
OK
NG



OK

4.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

NG

4.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY
a.

Replace the accelerator pedal sensor assembly.

Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>ACCELERATOR PEDAL>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL SENSOR DTCS)
5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL SENSOR DTCS)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Clear the DTCs.


e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS or Techstream on.


h.

Drive the vehicle in accordance with the driving pattern.


i.

Enter the following menus: Powertrain / EFI / Trouble Codes.


j.

Read the DTCs.


Result:
Result Proceed to
DTC P2120, P2122, P2123, P2125, P2127, P2128, and/or P2138 are output A
DTCs are not output B



A

B

END