Home › Power Source / Network › 1NR-VE BATTERY / CHARGING › CHARGING SYSTEM › from 2015.08
RM19Y0E _57 Power Source / Network _041458 1NR-VE BATTERY / CHARGING _0192571 CHARGING SYSTEM C

1NR-VE BATTERY / CHARGING  CHARGING SYSTEM  P0515  Battery Temperature Sensor System Malfunction  


DESCRIPTION

A110648E08
1.448,2.427 1.448,1.948 1.448,1.948 0.5,1.948 false 0.115,0.344 1.604,0.615 1.49,0.271 10 false Resistance (kΩ) 0.302,0.865 0.448,1.063 0.146,0.198 10 false 6 0.302,1.865 0.448,2.063 0.146,0.198 10 false 2 0.302,2.135 0.448,2.333 0.146,0.198 10 false 1 0.302,1.604 0.448,1.802 0.146,0.198 10 false 3 0.302,1.354 0.448,1.552 0.146,0.198 10 false 4 0.302,1.125 0.448,1.323 0.146,0.198 10 false 5 0.302,2.396 0.5,2.635 0.198,0.24 10 false 0 0.781,2.5 1,2.698 0.219,0.198 10 false 10 1.167,2.5 1.385,2.698 0.219,0.198 10 false 20 1.948,2.5 2.167,2.698 0.219,0.198 10 false 40 2.365,2.5 2.583,2.698 0.219,0.198 10 false 50 2.75,2.5 2.969,2.698 0.219,0.198 10 false 60 1.583,2.5 1.802,2.698 0.219,0.198 10 false 30 0.75,2.719 1.125,2.917 0.375,0.198 10 false (50) 1.125,2.719 1.5,2.917 0.375,0.198 10 false (68) 2.656,2.719 3.083,2.917 0.427,0.198 10 false (140) 2.25,2.719 2.719,2.917 0.469,0.198 10 false (122) 1.885,2.719 2.333,2.917 0.448,0.198 10 false (104) 1.51,2.719 1.885,2.917 0.375,0.198 10 false (86) 2.552,3.031 3.323,3.281 0.771,0.25 10 false °C (°F)

The battery temperature sensor installed on the battery current sensor assembly detects battery temperature.

A thermistor is integrated into the battery temperature sensor, and the resistance in the battery temperature sensor changes according to the battery temperature.

The resistance of the thermistor in the battery temperature sensor decreases as the battery temperature increases. The resistance increases as the temperature decreases.

The battery temperature sensor is connected to the ECM. The ECM supplies 5 V from the CM terminal to the battery temperature sensor through resistor R.

The battery temperature sensor and resistor R are connected in series. This results in fluctuations in the voltage supplied from the CM terminal when the resistance changes according to the battery temperature.

The ECM determines the battery temperature according to fluctuations in voltage. When the battery temperature is high, the ECM determines to reduce the amount of current supplied from the generator in order to protect the battery.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P0515 Battery Temperature Sensor System Malfunction Battery temperature sensor output value is less than 0.2 V for 0.5 seconds or more with the engine switch to ON
Battery temperature sensor output value is more than 4.8 V for 0.5 seconds or more with the engine switch to ON
(1 trip detection logic)
·

Battery current sensor assembly (battery temperature sensor)

·

Short to GND in battery temperature sensor circuit

·

ECM


Charging warning light does not come on DTC stored

WIRING DIAGRAM

B414474E02
2.021,0.563 2.479,0.76 0.458,0.198 10 false VDD 2.021,1.135 2.479,1.333 0.458,0.198 10 false GND 1.948,1.688 2.563,1.885 0.615,0.198 10 false VOUT 1.948,2.24 2.563,2.438 0.615,0.198 10 false TEMP 0.604,2.698 1.063,2.896 0.458,0.198 10 false C42 0.625,2.875 2.802,3.427 2.177,0.552 10 false Battery Current Sensor Assembly 2.396,0.563 2.552,0.76 0.156,0.198 10 false 2 2.396,1.135 2.552,1.333 0.156,0.198 10 false 4 2.385,1.688 2.542,1.885 0.156,0.198 10 false 3 2.385,2.24 2.542,2.438 0.156,0.198 10 false 1 5.135,0.573 5.448,0.771 0.313,0.198 10 false 56 5.063,1.125 5.521,1.323 0.458,0.198 10 false 100 5.125,1.688 5.438,1.885 0.313,0.198 10 false 78 5.135,2.26 5.448,2.458 0.313,0.198 10 false 34 5.365,0.656 5.979,0.854 0.615,0.198 10 false VC 5.375,1.219 5.688,1.417 0.313,0.198 10 false E2 5.365,1.771 5.677,1.969 0.313,0.198 10 false CM 5.375,2.323 5.875,2.615 0.5,0.292 10 false BATP 5.74,2.885 6.198,3.083 0.458,0.198 10 false C50 5.75,3.052 6.208,3.25 0.458,0.198 10 false ECM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS or Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - BATTERY CURRENT SENSOR ASSEMBLY)
a.

Disconnect the C50 ECM connector.


b.

Disconnect the C42 battery current sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C50-34 (BATP) - C42-1 (TEMP) Always Below 1Ω
C50-100 (E2) - C42-4 (GND) Always Below 1Ω
C50-34 (BATP) or C42-1 (TEMP) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the C50 ECM connector.


e.

Reconnect the C42 battery current sensor assembly connector.


Result:
Proceed to
OK
NG



OK

2.REPLACE BATTERY CURRENT SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.REPLACE BATTERY CURRENT SENSOR ASSEMBLY
a.

Replace the battery current sensor assembly with a new one.

Click herePower Source / Network>1NR-VE BATTERY / CHARGING>BATTERY CURRENT SENSOR>REMOVAL

Result:
Proceed to
NEXT




NEXT

3.CLEAR DTC
3.CLEAR DTC
a.

Turn the ignition switch to ON.


b.


NEXT

4.CHECK DTC (Present and Past DTCs)
4.CHECK DTC (Present and Past DTCs)
a.

Check for DTCs.

Click herePower Source / Network>1NR-VE BATTERY / CHARGING>CHARGING SYSTEM>DTC CHECK / CLEAR

Result:
Proceed to
DTC is output
DTC is not output




DTC is output

REPLACE FUEL INJECTION ECU

DTC is not output

END