Home › Power Source / Network › 1NR-VE BATTERY / CHARGING › CHARGING SYSTEM › from 2015.08
RM19Y0E _57 Power Source / Network _041458 1NR-VE BATTERY / CHARGING _0192571 CHARGING SYSTEM C

1NR-VE BATTERY / CHARGING  CHARGING SYSTEM  P0622  Alternator Field Duty Signal System Malfunction  


DESCRIPTION

The ECM determines the battery power according to the voltage of the BATT terminal while the engine is running (not cranking).

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P0622 Alternator Field Duty Signal System Malfunction Diagnosis condition: Ignition switch ON or after engine start
Abnormal condition:
Detection condition 1:
·

F duty 0%

·

C terminal duty 65% or higher

·

Alternator cut control is not active


Detection condition 2:
·

F duty 100%

·

Battery current is 2 A or less

·

During engine start


Duration of abnormality: 2 seconds or more
Number of trips: 1 trip
·

Wire harness or connector

·

Generator assembly

·

ECM


Charging warning light does not come on DTC stored

WIRING DIAGRAM

A371563E02
0.688,3.146 2.146,3.417 1.458,0.271 10 false Generator Assembly 1.99,0.49 2.396,0.781 0.406,0.292 10 false C52 2.052,0.313 2.271,0.563 0.219,0.25 10 false 1 1.792,0.49 2.01,0.74 0.219,0.25 10 false B 3.094,0.479 3.865,0.74 0.771,0.26 10 false to Battery 2,1 2.406,1.292 0.406,0.292 10 false C16 1.99,1.51 2.396,1.802 0.406,0.292 10 false C16 1.99,2.01 2.396,2.302 0.406,0.292 10 false C16 1.99,2.521 2.396,2.813 0.406,0.292 10 false C16 1.563,1 2.073,1.229 0.51,0.229 10 false ALTC 1.708,1.5 1.99,1.74 0.281,0.24 10 false FD 1.74,2.01 1.958,2.26 0.219,0.25 10 false IG 1.792,2.521 1.958,2.729 0.167,0.208 10 false L 2.063,0.813 2.281,1.063 0.219,0.25 10 false 1 2.073,1.333 2.292,1.583 0.219,0.25 10 false 3 2.073,1.833 2.292,2.083 0.219,0.25 10 false 2 2.073,2.354 2.292,2.604 0.219,0.25 10 false 4 5.042,0.979 5.552,1.208 0.51,0.229 10 false ALTO 5.042,2.01 5.552,2.24 0.51,0.229 10 false ALT 5.052,2.521 5.219,2.729 0.167,0.208 10 false L 5.042,1.51 5.552,1.74 0.51,0.229 10 false ALTI 5.5,3.302 6.01,3.531 0.51,0.229 10 false ECM 5.479,3.146 5.99,3.375 0.51,0.229 10 false C50 4.688,0.885 5.021,1.135 0.333,0.25 10 false 107 4.76,1.927 5.094,2.177 0.333,0.25 10 false 86 4.708,1.417 5.042,1.667 0.333,0.25 10 false 108 4.771,2.417 5.104,2.667 0.333,0.25 10 false 85

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS or Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (GTS or Techstream data reading (alternator field duty))
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Powertrain / EFI / Data List.


e.

According to the display on the GTS or Techstream, read the Data List.

Powertrain > EFI > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Alternator field duty Generator output duty Min.: 0%, Max.: 400% Increases to a certain value, and then becomes stable: Immediately after engine start, during idling (no electric load, air conditioner OFF) Determines ON/OFF status of alternator FD terminal and displays it as a duty ratio.
Increases: After engine warm-up, during idling, electric load is turned from off to on.

OK:

During idling, the value does not stay at 0%.


HINT:

The alternator cut control may activate for a short period of time during and after the engine start. This may cause the [Alternator field duty] value to become 0%. However, this is not a malfunction.



Result:
Proceed to
OK
NG



NG

2.INSPECT GENERATOR ASSEMBLY

OK

2.INSPECT GENERATOR ASSEMBLY
a.

b.

Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (GENERATOR ASSEMBLY - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (GENERATOR ASSEMBLY - ECM)
a.

Disconnect the C16 generator assembly connector.


b.

Disconnect the C50 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C16-3 (FD) - C50-108(ALTI) Always Below 1 Ω
C16-3 (FD) and C50-108(ALTI) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR