Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › from 2015.08
RM19Y0E _54 Brake _002992 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0015137 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1241/15  Low or High Power Supply Voltage  C1241/16  Low or High Power Supply Voltage  


DESCRIPTION

This DTC is stored when the +IG terminal voltage deviates from the DTC detection condition due to a malfunction in the power supply or charging circuit, such as the battery or generator circuit, etc.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C1241/15 Low or High Power Supply Voltage
1.

Solenoid power supply voltage remains under the threshold value for a certain period of time.

2.

ECU indicates a power supply failure remains for a certain period of time.


·

ABS2 fuse

·

ECU-IG1 fuse

·

Battery

·

Charging system

·

Power source circuit

·

Internal power supply circuit of skid control ECU (Brake actuator assembly)


-
C1241/16 Low or High Power Supply Voltage When ECU power supply voltage goes over the threshold value.
·

ABS2 fuse

·

ECU-IG1 fuse

·

Battery

·

Charging system

·

Power source circuit

·

Internal power supply circuit of skid control ECU (Brake actuator assembly)


-

WIRING DIAGRAM

C335027E02
0.417,1.135 1.354,1.365 0.938,0.229 10 false from IG Circuit 2.729,1.344 3.375,1.573 0.646,0.229 10 false ECU-IG1 4.531,1.021 4.792,1.292 0.26,0.271 10 false 12 4.542,1.625 4.802,1.896 0.26,0.271 10 false 25 4.594,2.292 4.854,2.563 0.26,0.271 10 false 1 4.833,1.146 5.167,1.385 0.333,0.24 10 false +IG 4.833,1.771 5.333,2.021 0.5,0.25 10 false GND1 4.844,2.438 5.323,2.677 0.479,0.24 10 false GND2 4.25,2.844 4.583,3.083 0.333,0.24 10 false A13 4.229,3.031 7.031,3.281 2.802,0.25 10 false Skid Control ECU (Brake Actuator Assembly) 0.542,0.563 1.375,0.813 0.833,0.25 10 false from Battery 2.813,0.76 3.26,0.99 0.448,0.229 10 false ABS2 4.833,0.594 5.167,0.833 0.333,0.24 10 false +BS 4.531,0.458 4.792,0.729 0.26,0.271 10 false 38

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the skid control ECU (brake actuator assembly) is replaced with a new one, the skid control ECU makes the shift to test mode automatically when the ignition switch is turned to ON for the first time. Be sure to complete the test mode checks.



PROCEDURE

1.CHECK BATTERY
a.

Check the battery voltage.

Standard Voltage:

11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (+IG, +BS TERMINAL)

NG

2.CHECK TERMINAL VOLTAGE (+IG, +BS TERMINAL)
a.
C330019C31
1.5,0.167 1.917,0.417 0.417,0.25 2.406,0.448 2.25,0.99 true 2.74,1.823 2.563,1.333 true 0.083,0.094 0.396,0.25 0.313,0.156 10 false *a 1.573,0.208 2.031,0.406 0.458,0.198 10 false A13 2.635,1.865 3.094,2.063 0.458,0.198 10 false +BS 2.448,0.302 2.906,0.5 0.458,0.198 10 false +IG
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Disconnect the A13 skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A13-12 (+IG) - Body ground Ignition switch ON 11 to 14 V
A13-38 (+BS) - Body ground Always 11 to 14 V


Result:
Proceed to
OK
NG




OK

3.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)
a.

Turn the ignition switch off.


b.

Disconnect the A13 skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-25 (GND1) - Body ground Always Below 1 Ω
A13-1 (GND2) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG




OK

4.READ VALUE USING GTS OR TECHSTREAM (ECU POWER VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING GTS OR TECHSTREAM (ECU POWER VOLTAGE)
a.

Turn the ignition switch off.


b.

Connect the GTS or Techstream to the DLC3.


c.

Start the engine.


d.

Turn the GTS or Techstream on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
+IG 1 voltage +IG voltage value Min.: 0.00 V
Max.: 20.00 V
Ignition switch on: 11 to 14 V Changes in proportion to battery voltage
Solenoid valve power voltage +BS voltage value Min.: 0.00 V
Max.: 20.00 V
Always: 11.00 to 14.00 V Changes in proportion to battery voltage

OK:

Normal



f.

Using the GTS or Techstream, check the input of the stop light switch operation when the brake pedal is operated.

Result:
Proceed to
OK
NG




OK

5.RECONFIRM DTC

NG

5.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 20 km/h (12 mph) or more.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
DTC not output A
DTC output B


HINT:

If troubleshooting has been carried out according to the problem symptoms table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR




A

B