Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › from 2015.08
RM19Y0E _55 Steering _002997 POWER ASSIST SYSTEMS _0015160 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1523/23  Motor Terminal Abnormality 1  C1524/24  Motor Terminal Abnormality 2  C1555/55  Motor Relay Failure  


DESCRIPTION

The power steering ECU supplies current to the power steering motor through the motor circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Return-to-normal Condition Note
C1523/23 Motor Terminal Abnormality 1 Motor disconnection
·

Steering column assembly (Power steering motor)

·

Power steering ECU assembly


Comes on (Red) Ignition switch ON again Buzzer :
Sounds in termittently
C1524/24 Motor Terminal Abnormality 2 Excessive voltage, low voltage, short circuit between both terminals of motor.
·

Steering column assembly (Power steering motor)

·

Power steering ECU assembly


Comes on (Red) Ignition switch ON again Buzzer :
Sounds in termittently
C1555/55 Motor Relay Failure Motor relay circuit malfunction
·

Steering column assembly (Power steering motor)

·

Power steering ECU assembly


Comes on (Red) Ignition switch ON again Buzzer :
Sounds in termittently

WIRING DIAGRAM

C245578E05
2.26,1.865 3.74,2.229 1.479,0.365 10 false Power Steering Motor 1.396,3.052 3.281,3.344 1.885,0.292 10 false Steering Column Assembly 4.469,1.604 4.646,1.75 0.177,0.146 10 false z1 4.479,2.49 4.667,2.656 0.188,0.167 10 false z1 4.51,1.396 4.604,1.563 0.094,0.167 10 false 1 4.51,2.313 4.646,2.479 0.135,0.167 10 false 2 4.792,1.604 5.073,1.781 0.281,0.177 10 false M1 4.792,2.5 5.031,2.677 0.24,0.177 10 false M2 4.354,3.104 6.323,3.365 1.969,0.26 10 false Power Steering ECU Assembly 5.625,2.5 5.969,2.729 0.344,0.229 10 false E74 5.708,2.302 5.854,2.469 0.146,0.167 10 false 2 5.25,2.5 5.573,2.667 0.323,0.167 10 false GND 4.427,0.646 4.75,0.875 0.323,0.229 10 false E74 4.5,0.458 4.615,0.604 0.115,0.146 10 false 1 4.792,0.635 5.24,0.833 0.448,0.198 10 false BAT+ 2.833,0.844 3.177,1.031 0.344,0.188 10 false EPS 0.573,0.615 1.417,0.833 0.844,0.219 10 false from Battery

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION
a.
C332781C01
1.5,0.438 1.833,0.625 0.333,0.188 1.604,0.448 1.917,0.646 0.313,0.198 10 false z1 0.115,0.083 0.427,0.281 0.313,0.198 10 false *a
*a Component with harness connected
(Power Steering ECU Assembly)


Check the connection condition of the z1 power steering motor connector.

OK:

Power steering motor connector is securely connected to the power steering ECU assembly.


Result:
Proceed to
OK
NG




OK

2.INSPECT POWER STEERING ECU ASSEMBLY

NG

CONNECT CONNECTOR SECURELY

2.INSPECT POWER STEERING ECU ASSEMBLY
a.
C332781C05
2.24,0.406 2.625,0.604 0.385,0.198 1.479,0.417 1.865,0.615 0.385,0.198 2.667,1.74 2.281,1.052 true 1.896,1.792 1.792,1.042 true 1.375,1.781 1.563,1.042 true 1.604,0.427 1.917,0.625 0.313,0.198 10 false z1 2.313,0.427 2.625,0.625 0.313,0.198 10 false E74 2.385,1.792 2.969,2.01 0.583,0.219 10 false 2 (GND) 1.188,1.823 1.656,2.042 0.469,0.219 10 false 2 (M2) 1.729,1.823 2.198,2.042 0.469,0.219 10 false 1 (M1) 0.156,0.094 0.469,0.292 0.313,0.198 10 false *a
*a Component with harness connected
(Power Steering ECU Assembly)


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition
(Steering Position)
Specified Condition
z1-1 (M1) - E74-2 (GND) Ignition switch ON, steering wheel turned to right Below 1 V
Ignition switch ON, steering wheel turned to left 11 to 14 V
z1-2 (M2) - E74-2 (GND) Ignition switch ON, steering wheel turned to right 11 to 14 V
Ignition switch ON, steering wheel turned to left Below 1 V


Result:
Proceed to
OK
NG




OK

3.INSPECT STEERING COLUMN ASSEMBLY (POWER STEERING MOTOR)

NG

4.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BATTERY AND BODY GROUND)
3.INSPECT STEERING COLUMN ASSEMBLY (POWER STEERING MOTOR)
a.

Disconnect the z1 power steering ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z1-1 (M1) - z1-2 (M2) Always Below 1 Ω
z1-1 (M1) - Body ground Always 1 MΩ or higher
z1-2 (M2) - Body ground Always 1 MΩ or higher


Result:
Proceed to
OK
NG




OK

4.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPLACE STEERING COLUMN ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.
C332781C06
2.24,0.406 2.625,0.604 0.385,0.198 2.083,1.698 2.313,1.031 true 2.792,1.719 2.552,1.042 true 2.313,0.427 2.708,0.667 0.396,0.24 10 false E74 1.792,1.74 2.375,1.958 0.583,0.219 10 false 2 (GND) 2.552,1.771 3.146,2.021 0.594,0.25 10 false 1 (BAT+) 0.167,0.094 0.479,0.292 0.313,0.198 10 false *a
*a Component with harness connected
(Power Steering ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E74-1 (BAT+) - Body ground Always 11 to 14 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E74-2 (GND) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG




OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

CHECK FOR HARNESS OR CONNECTOR