Home › Drivetrain › A4R AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION UNIT › from 2015.08
RM19Y0E _52 Drivetrain _041457 A4R AUTOMATIC TRANSMISSION / TRANSAXLE _0197969 AUTOMATIC TRANSMISSION UNIT G

A4R AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION UNIT  INSPECTION  


PROCEDURE

Hide 35771D 1.INSPECT OUTPUT SHAFT BALL BEARING

a.
C153983

Check the output shaft ball bearing whether it is rough or worn.

If necessary, replace the output shaft ball bearing.


Hide 35301 2.INSPECT FRONT OIL PUMP BODY SUB-ASSEMBLY

Hide 35610 3.INSPECT FRONT MULTIPLE DISC CLUTCH ASSEMBLY

a.
C154027

Using a feeler gauge, measure the forward clutch piston stroke.

Piston stroke:

0.33 to 1.27 mm (0.0130 to 0.0500 in.)


If the piston stroke is greater than the maximum, replace the front multiple disc clutch assembly.


b.
C154026

Using a feeler gauge, measure the reverse clutch piston stroke.

Piston stroke:

0.67 to 0.98 mm (0.0264 to 0.0386 in.)


If the piston stroke is greater than the maximum, replace the front multiple disc clutch assembly.


c.
C154028

Using a dial indicator, measure the inside diameter of the front multiple disc drum.

Standard inside diameter:

44.50 to 44.52 mm (1.7520 to 1.7528 in.)


Maximum inside diameter:

44.58 mm (1.7551 in.)


If the inside diameter is greater than the maximum, replace the front multiple disc clutch assembly.


d.
C154034

Install the forward clutch hub into the front multiple disc drum.


e.

Turn the forward clutch hub, and check that the clutch discs rotate smoothly.


f.
C154035

Install the front planetary sun gear sub-assembly into the front multiple disc drum.


g.

Turn the front planetary sun gear sub-assembly, and check that the clutch discs rotate smoothly.


Hide 35650 4.INSPECT REAR MULTIPLE DISC CLUTCH ASSEMBLY

a.
C154036

Using a feeler gauge, measure the rear clutch piston stroke.

Piston stroke:

1.20 to 1.51 mm (0.0472 to 0.0594 in.)


If the piston stroke is greater than the maximum, replace the rear multiple disc clutch assembly.


b.
C154037

Install the intermediate shaft sub-assembly into the rear multiple disc drum.


c.

Turn the intermediate shaft sub-assembly, and check that the clutch discs rotate smoothly.


Hide 35633B 5.INSPECT FORWARD MULTIPLE DISC CLUTCH CLUTCH DISC

a.
C270801

Check if the sliding surfaces of the forward multiple disc clutch clutch discs, No. 1 clutch plates and reverse clutch flange are worn or burnt. If necessary, replace them.

HINT:

Before assembling new forward multiple disc clutch clutch discs, soak them in Toyota Genuine ATF Type T-IV for at least 15 minutes.



Hide 35633F 6.INSPECT FRONT CLUTCH CLUTCH DISC

a.
C270801

Check if the sliding surfaces of the front clutch clutch discs, No. 2 clutch plates and forward clutch flange are worn or burnt. If necessary, replace them.

HINT:

Before assembling new front clutch clutch discs, soak them in Toyota Genuine ATF Type T-IV for at least 15 minutes.



Hide 35673 7.INSPECT REAR CLUTCH DISC

a.
C184859

Check if the sliding surfaces of the rear clutch flanges, rear clutch discs, No. 3 clutch plate and rear clutch cushion plate are worn or burnt. If necessary, replace them.

HINT:

Before assembling new rear clutch discs, soak them in Toyota Genuine ATF Type T-IV for at least 15 minutes.



Hide 35706V 8.INSPECT PLANETARY SUN GEAR SUB ASSEMBLY

a.
C153984

Using a dial indicator, measure the inside diameter of the planetary sun gear bushing.

Maximum inside diameter:

27.07 mm (1.0657 in.)


If the inside diameter is greater than the maximum, replace the planetary sun gear sub-assembly.


Hide 35709K 9.INSPECT REAR PLANETARY GEAR SUB-ASSEMBLY

a.
C153985

Using a dial indicator, measure the inside diameter of the rear planetary gear bushings.

Maximum inside diameter:

18.07 mm (0.7114 in.)


If the inside diameter is greater than the maximum, replace the rear planetary gear sub-assembly.


Hide 35681 10.INSPECT NO. 1 BRAKE DISC

a.
C153986

Check if the sliding surfaces of the No. 1 brake discs, brake plates and No. 1 brake flange are worn or burnt. If necessary, replace them.

HINT:

Before assembling new No. 1 brake discs, soak them in Toyota Genuine ATF Type T-IV for at least 15 minutes.



Hide 35790A 11.INSPECT 1 WAY CLUTCH ASSEMBLY

a.
C153987C01
1.104,0.802 0.802,0.865 false 1.708,0.833 2.229,0.615 true 1.479,0.083 2.031,0.583 0.552,0.5 10 *b 2.26,0.531 2.781,0.979 0.521,0.448 10 *d 0.896,0.198 1.375,0.677 0.479,0.479 10 *a 0.615,0.771 1.073,1.24 0.458,0.469 10 *c
*a Lock
*b Free
*c Hold
*d Turn


Hold the planetary gear and turn the hub. The hub should turn freely clockwise and should lock counterclockwise.

If necessary, replace the 1 way clutch assembly.


Hide 35883A 12.INSPECT BRAKE DISC

a.
C153988

Check if the sliding surfaces of the brake discs, brake plates and brake flanges are worn or burnt. If necessary, replace them.

HINT:

Before assembling new brake discs, soak them in Toyota Genuine ATF Type T-IV for at least 15 minutes.



Hide 35740A 13.INSPECT FRONT PLANETARY RING GEAR ASSEMBLY

a.
C153989

Using a dial indicator, measure the inside diameter of the front planetary ring gear assembly.

Maximum inside diameter:

13.07 mm (0.5146 in.)


If the inside diameter is greater than the maximum, replace the front planetary ring gear assembly.