Home › Steering › STEERING GEAR / LINKAGE › STEERING GEAR › from 2015.08
RM19Y0E _55 Steering _002999 STEERING GEAR / LINKAGE _0015165 STEERING GEAR A

STEERING GEAR / LINKAGE  STEERING GEAR  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for both the RHD and LHD vehicles.

·

The procedure described below is for the LHD vehicles.



PROCEDURE

Hide 1.PLACE FRONT WHEELS FACING STRAIGHT AHEAD

Hide 2.REMOVE FRONT WHEEL

Hide 51441 3.REMOVE NO. 1 ENGINE UNDER COVER

Hide 51443 4.REMOVE NO. 2 ENGINE UNDER COVER (w/ No. 2 Engine Under Cover)

Hide 45220 5.SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C161006C02
1.771,0.615 1.125,0.656 1.125,0.656 1.75,0.76 true 0.917,0.552 1.156,0.75 0.24,0.198 10 *a
*a Matchmark


Put matchmarks on the steering intermediate shaft assembly and the steering gear assembly.


b.

Remove the bolt and separate the steering intermediate shaft assembly from the power steering gear.


Hide 45047 6.SEPARATE TIE ROD END SUB-ASSEMBLY LH

a.

Remove the nut.


b.
C177184N01
2.26,0.748 2.565,0.913 0.304,0.166 10 SST 2.031,1.149 2.031,0.839 2.031,0.839 2.249,0.839 false

Install SST to the tie rod end sub-assembly LH.

SST
09960-20010  (09961-02060)

NOTICE:

Make sure that the upper end of the tie rod end sub-assembly LH and SST are aligned.



c.

Using SST, remove the tie rod end sub-assembly LH from the steering knuckle.

SST
09960-20010  (09961-02010)

C201536C02
1.375,0.552 1.573,0.333 1.573,0.333 1.75,0.333 false 3.594,1.823 3.438,2.198 3.438,2.198 3.354,2.198 true 6.094,1.938 6.219,1.938 6.219,1.938 6.302,1.677 false 1.844,1.708 2.01,1.875 0.167,0.167 10 A 1.844,1.938 2,2.125 0.156,0.188 10 B 1.781,0.24 2.052,0.427 0.271,0.188 10 *a 3.042,2.135 3.385,2.333 0.344,0.198 10 SST 5.01,2.125 5.365,2.333 0.354,0.208 10 *c 5.896,1.875 6.156,2.063 0.26,0.188 10 *b
*a Tie the string without allowing slack *b Place the wrench here
*c Turn - -
V100135

Molybdenum grease - -


CAUTION:

Apply molybdenum grease to the bolt threads and the tip of SST.


NOTICE:
·

Be sure to tighten the string firmly to secure SST to the steering knuckle and prevent it from falling off.

·

Install SST with the center nut so that A and B are parallel. Otherwise, the dust cover may be damaged.

·

Be sure to place the wrench on the part indicated in the illustration.

·

Do not damage the front disc brake dust cover.

·

Do not damage the ball joint dust cover.

·

Do not damage the steering knuckle.




Hide 45046 7.SEPARATE TIE ROD END SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 45510 8.REMOVE STEERING GEAR ASSEMBLY

a.
C250996

Remove the 4 bolts and separate the steering gear assembly from the front suspension cross member.


b.

While removing the steering gear assembly, separate the intermediate shaft assembly from the steering gear assembly.