Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › from 2016.09
RM19Y0E _53 Suspension _059025 TIRE PRESSURE MONITORING _0288381 TIRE PRESSURE WARNING SYSTEM M

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  REGISTRATION  


PROCEDURE

Hide 1. BEFORE REGISTRATION

NOTICE:

The transmitter ID is written on the tire pressure warning valve and transmitter. It is not possible to read the transmitter ID after installing the tire to the wheel. Therefore, make a note of the transmitter ID before installing the tire.


a.

In case of tire pressure warning ECU and receiver replacement:

i.

Read the registered transmitter IDs that are stored in the old ECU using the GTS and note them down.


ii.

If reading the stored transmitter IDs is impossible due to malfunctions of components such as the tire pressure warning ECU and receiver, remove the tires from the wheels and check the IDs located on the tire pressure warning valve and transmitters.



b.

In case of tire pressure warning valve and transmitter replacement:

i.

Take a note of the 7 digit number (transmitter ID) written on the tire pressure warning valve and transmitter.

C349073C01
6.125,1.313 6.458,0.979 true 0.188,0.156 0.5,0.313 0.313,0.156 10 false *1 6.51,0.885 6.823,1.042 0.313,0.156 10 false *a
*1 Tire Pressure Warning Valve and Transmitter *a Transmitter ID (7 Digit Number)




Hide 2.REGISTER TRANSMITTER ID

HINT:
·

The previously registered IDs will be cleared from memory when the registration is completed.

·

If the ID registration step is not completed within 300 seconds, ID registration will be canceled.



a.

Set the air pressure of all tires to the specified value(s).

Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch ON and the GTS on.


e.

Enter the following menus: Chassis / Tire Pressure Monitor / Utility / ID Registration.


f.

Perform the procedure displayed on the GTS.


Hide 3. CONFIRMATION OF TRANSMITTER ID REGISTRATION

NOTICE:
·

It may take up to a few minutes to update the tire pressure data. If the values are not displayed after a few minutes, perform troubleshooting according to the inspection procedure for DTCs C2121/21 to C2125/25.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>C2121/21

·

If the IDs have not been registered, DTC C2171/71 is stored in the tire pressure warning ECU and receiver after 3 minutes or more.

·

If normal pressure values are displayed, the IDs have been registered correctly.

·

If the tire pressure values are not displayed after a few minutes, the IDs may be incorrect or the system may have a malfunction.

·

After all IDs are registered, DTC C2126/26 is stored in the tire pressure warning ECU and receiver and the tire pressure warning light blinks for 1 minute and then illuminates. When the tire pressure warning ECU and receiver successfully receives signals from all the transmitters whose IDs are stored in the ECU, DTC C2126/26 is cleared and the tire pressure warning light goes off.



a.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

Chassis > Tire Pressure Monitor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ID1 Tire Inflation Pressure ID1 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) /380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*1
ID2 Tire Inflation Pressure ID2 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) /380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed,data has not been received.*1
ID3 Tire Inflation Pressure ID3 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) /380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed,data has not been received.*1
ID4 Tire Inflation Pressure ID4 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) /380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed,data has not been received.*1
ID5 Tire Inflation Pressure ID5 Tire Inflation Pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/ cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*1

HINT:
·

*1: It may take a few minutes until the values are displayed.

·

The wheel position cannot be determined from ID1 through ID5 on the Data List.




b.

Read the "ID Tire Inflation Pressure" values.


c.

Confirm that the tire pressure data of all tires is displayed on the GTS screen.


d.

Reduce the tire inflation pressure of each tire 40 kPa (0.4 kgf/cm2, 5.8 psi) or more, and check that the "ID Tire Inflation Pressure" data is updated and that the actual tire inflation pressures are displayed.


e.

After confirming that all of the tire inflation pressure values have been updated, adjust the tire inflation pressure to the specified value, press the tire pressure warning reset switch and perform initialization.