Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE › from 2016.09
RM19Y0E _58 Vehicle Interior _003010 SUPPLEMENTAL RESTRAINT SYSTEMS _0015209 SPIRAL CABLE G

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE  INSPECTION  


PROCEDURE

Hide 84306 1.INSPECT SPIRAL CABLE SUB-ASSEMBLY (w/o VSC)

a.

If there are any defects as mentioned below, replace the spiral cable sub-assembly with a new one:

Scratches, cracks, dents or chips in the connector or spiral cable sub-assembly.


b.
B412679C05
1.604,0.219 1.906,0.438 0.302,0.219 0.375,1.229 0.677,1.448 0.302,0.219 2.104,3.365 2.448,3.594 0.344,0.229 0.781,3.271 1.125,3.5 0.344,0.229 1.99,3.938 1.823,3.615 true 2.208,3.958 2.583,3.531 true 1.156,3.792 1.354,3.469 true 0.948,3.802 0.615,3.531 true 0.427,3.99 0.802,3.875 true 0.552,4.26 1.01,3.865 true 1.417,4.219 1.302,3.885 true 1.677,0.24 1.99,0.438 0.313,0.198 10 false z7 0.448,1.25 0.76,1.448 0.313,0.198 10 false z5 0.833,3.302 1.146,3.5 0.313,0.198 10 false E67 2.156,3.396 2.469,3.594 0.313,0.198 10 false E63 1.26,3.292 1.573,3.49 0.313,0.198 10 false AU1 0.354,3.354 0.667,3.552 0.313,0.198 10 false IL+2 0.292,3.917 0.604,4.115 0.313,0.198 10 false + 0.281,4.26 0.594,4.458 0.313,0.198 10 false AU2 1.375,4.25 1.688,4.448 0.313,0.198 10 false EAU 1.708,3.458 2.021,3.656 0.313,0.198 10 false D+ 2.625,3.417 2.938,3.615 0.313,0.198 10 false D-
*a Component without harness connected
(Spiral Cable Sub-assembly)


Check the spiral cable sub-assembly.

i.

Set the spiral cable sub-assembly to the center position.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION


ii.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise and measure the resistance according to the value(s) in the table below.

NOTICE:

Do not turn the spiral cable sub-assembly by the airbag wire harness.


Standard Resistance (w/ Steering Pad Switch):
Tester Connection Condition Specified Condition
E63-1 (D+) - z5-2 Always Below 1 Ω
E63-2 (D-) - z5-1 Always Below 1 Ω
E67-8 (+) - z7-1 Always 3 Ω or less
E67-9 (IL+2) - z7-2 Always 3 Ω or less
E67-10 (AU2) - z7-3 Always 3 Ω or less
E67 - 11 (AU1) - z7-4 Always 3 Ω or less
E67 -12 (EAU) - z7-5 Always 3 Ω or less


Standard Resistance (w/o Steering Pad Switch):
Tester Connection Condition Specified Condition
E63-1 (D+) - z5-2 Always Below 1 Ω
E63-2 (D-) - z5-1 Always Below 1 Ω
E67-8 (+) - z7-1 Always 3 Ω or less


If the result is not as specified, replace the spiral cable sub-assembly.


iii.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then, while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance according to the value(s) in the table below.

NOTICE:

Do not turn the spiral cable sub-assembly by the airbag wire harness.


Standard Resistance (w/ Steering Pad Switch):
Tester Connection Condition Specified Condition
E63-1 (D+) - z5-2 Always Below 1 Ω
E63-2 (D-) - z5-1 Always Below 1 Ω
E67-8 (+) - z7-1 Always 3 Ω or less
E67-9 (IL+2) - z7-2 Always 3 Ω or less
E67-10 (AU2) - z7-3 Always 3 Ω or less
E67 - 11 (AU1) - z7-4 Always 3 Ω or less
E67 -12 (EAU) - z7-5 Always 3 Ω or less


Standard Resistance (w/o Steering Pad Switch):
Tester Connection Condition Specified Condition
E63-1 (D+) - z5-2 Always Below 1 Ω
E63-2 (D-) - z5-1 Always Below 1 Ω
E67-8 (+) - z7-1 Always 3 Ω or less


If the result is not as specified, replace the spiral cable sub-assembly.

NOTICE:

As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.




Hide 84941A 2.INSPECT SWITCH BASE (w/ VSC)

a.

If there are any defects as mentioned below, replace the switch base with a new one:

Scratches, cracks, dents or chips in the connector or switch base.


b.
B412679C03
0.792,3.25 1.167,3.5 0.375,0.25 2.073,3.313 2.448,3.563 0.375,0.25 1.646,0.167 2.021,0.417 0.375,0.25 0.344,1.229 0.719,1.479 0.375,0.25 1.948,3.948 1.802,3.635 true 2.229,3.948 2.604,3.563 true 1.271,3.885 1.406,4.333 true 1.146,3.792 1.333,3.406 true 0.594,4.323 1.031,3.875 true 0.604,3.479 0.885,3.802 true 0.448,3.99 0.781,3.875 true 0.844,3.302 1.302,3.5 0.458,0.198 10 false E67 2.125,3.354 2.583,3.552 0.458,0.198 10 false E63 1.76,0.208 2.219,0.406 0.458,0.198 10 false z7 0.448,1.281 0.906,1.479 0.458,0.198 10 false z5 1.583,3.521 1.854,3.708 0.271,0.188 10 false D+ 2.646,3.469 2.917,3.656 0.271,0.188 10 false D- 0.292,3.385 0.667,3.583 0.375,0.198 10 false IL+2 0.281,4.229 0.656,4.427 0.375,0.198 10 false AU2 1.406,3.313 1.781,3.51 0.375,0.198 10 false AU1 1.448,4.271 1.823,4.469 0.375,0.198 10 false EAU 0.302,3.906 0.573,4.094 0.271,0.188 10 false +
*a Component without harness connected
(Switch Base)


Check the switch base.

i.

Set the switch base to the center position.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION


ii.

After setting the switch base to the center position, rotate the switch base 2.5 times clockwise and measure the resistance according to the value(s) in the table below.

NOTICE:

Do not turn the switch base by the airbag wire harness.


Standard Resistance (w/ Steering Pad Switch):
Tester Connection Condition Specified Condition
E63-1 (D+) - z5-2 Always Below 1 Ω
E63-2 (D-) - z5-1 Always Below 1 Ω
E67-8 (+) - z7-1 Always 3 Ω or less
E67-9 (IL+2) - z7-2 Always 3 Ω or less
E67-10 (AU2) - z7-3 Always 3 Ω or less
E67 - 11 (AU1) - z7-4 Always 3 Ω or less
E67 -12 (EAU) - z7-5 Always 3 Ω or less


Standard Resistance (w/o Steering Pad Switch):
Tester Connection Condition Specified Condition
E63-1 (D+) - z5-2 Always Below 1 Ω
E63-2 (D-) - z5-1 Always Below 1 Ω
E67-8 (+) - z7-1 Always 3 Ω or less


If the result is not as specified, replace the switch base.


iii.

After setting the switch base to the center position, rotate the switch base 2.5 times clockwise. Then, while rotating the switch base 5 times counterclockwise, measure the resistance according to the value(s) in the table below.

NOTICE:

Do not turn the switch base by the airbag wire harness.


Standard Resistance (w/ Steering Pad Switch):
Tester Connection Condition Specified Condition
E63-1 (D+) - z5-2 Always Below 1 Ω
E63-2 (D-) - z5-1 Always Below 1 Ω
E67-8 (+) - z7-1 Always 3 Ω or less
E67-9 (IL+2) - z7-2 Always 3 Ω or less
E67-10 (AU2) - z7-3 Always 3 Ω or less
E67 - 11 (AU1) - z7-4 Always 3 Ω or less
E67 -12 (EAU) - z7-5 Always 3 Ω or less


Standard Resistance (w/o Steering Pad Switch):
Tester Connection Condition Specified Condition
E63-1 (D+) - z5-2 Always Below 1 Ω
E63-2 (D-) - z5-1 Always Below 1 Ω
E67-8 (+) - z7-1 Always 3 Ω or less


If the result is not as specified, replace the switch base.

NOTICE:

As the switch base may break, do not rotate the switch base more than the specified amount.