Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE › from 2016.09
RM19Y0E _58 Vehicle Interior _003010 SUPPLEMENTAL RESTRAINT SYSTEMS _0015209 SPIRAL CABLE A

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE  INSTALLATION  


PROCEDURE

Hide 84941A 1.INSTALL SWITCH BASE (w/ VSC)

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:
B452516

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS.



c.

Check that the front wheels are facing straight ahead.


d.
B457883C01
0.458,2.448 0.844,1.896 true 2.302,1.521 2.802,1.438 true 0.323,2.469 0.635,2.625 0.313,0.156 10 false *a 2.885,1.302 3.198,1.458 0.313,0.156 10 false *a
*a Do not push the claws


Using pliers, expand the clamp as shown in the illustration.


e.

Engage the 2 guides and claw.

NOTICE:

Do not push the claws when installing the switch base.



f.

Release the clamp to install the switch base.


g.
B463021C01
0.688,3.219 0.802,3.115 true 2.375,3.198 2.521,3.094 true 0.302,3.167 0.729,3.323 0.427,0.156 10 false *1(*a) 2.167,3.125 2.479,3.281 0.313,0.156 10 false *2
*1 Lock Slider
*2 Airbag Connector (Yellow Colored)
*a Lock Position


Connect the airbag connector (yellow colored) .

NOTICE:

When handling the airbag connector, take care not to damage the airbag wire harness.



h.

Connect the 2 connectors.


Hide 84650 2.INSTALL WINDSHIELD WIPER SWITCH ASSEMBLY (w/ VSC)

Hide 84140 3.INSTALL HEADLAMP DIMMER SWITCH ASSEMBLY (w/ VSC)

Hide 84306 4.INSTALL SPIRAL CABLE SUB-ASSEMBLY (w/o VSC)

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:
B452516

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS.



c.

Check that the front wheels are facing straight ahead.


d.

Attach the 3 claws to install the spiral cable sub-assembly.


e.
B263617

If installing a new spiral cable sub-assembly:

Remove the lock pin.


f.
B412680C02
2.292,3.208 2.573,3.167 false 0.719,3.25 0.833,3.156 true 0.323,3.146 0.771,3.344 0.448,0.198 10 false *1(*a) 2.094,3.125 2.542,3.323 0.448,0.198 10 false *2
*1 Lock Slider
*2 Airbag Connector (Yellow Colored)
*a Lock Position


Connect the connector to the spiral cable sub-assembly.


g.

Connect the airbag connector (yellow colored) to the spiral cable sub-assembly.

NOTICE:

When handling the airbag connector, take care not to damage the airbag wire harness.



h.

Check that the lock slider is in the lock position.


Hide 84306 5.ADJUST SPIRAL CABLE SUB-ASSEMBLY

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:
B452516

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.




c.
B456224C01
0.333,1.042 0.625,1.531 true 2.802,1.74 3.125,2.021 3.125,2.021 2.823,1.813 true 3.188,2.021 3.427,2.177 0.24,0.156 10 false *a 0.188,0.865 0.5,1.021 0.313,0.156 10 false *b
*a Matchmark
*b Flat Cable


Check if the spiral cable sub-assembly is centered.

NOTICE:

Check that the front wheels are aligned facing straight ahead.


HINT:

When the spiral cable sub-assembly is centered, the flat cable shown in the illustration is visible.



d.

If the spiral cable sub-assembly is not centered, center it.

NOTICE:
·

Do not rotate the spiral cable with sensor sub-assembly with the battery connected and the ignition switch ON.

·

To avoid an open circuit, do not use force when rotating the spiral cable sub-assembly

·

As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.

·

Check that the front wheels are aligned facing straight ahead.




e.
B412682C02
0,0 0,0 false
V100135

Counterclockwise


Rotate the spiral cable sub-assembly counterclockwise slowly by hand until it feels firm.

NOTICE:

Do not turn the spiral cable sub-assembly by the airbag wire harness.



f.
B456222C01
2.813,1.823 3.125,2.01 3.125,2.01 2.813,1.729 true 0.24,1.073 0.646,1.552 true 3.177,2.021 3.365,2.177 0.188,0.156 10 false *a 0.104,0.927 0.417,1.083 0.313,0.156 10 false *b
*a Matchmark
*b Flat Cable
V100135

Clockwise


Rotate the spiral cable sub-assembly clockwise approximately 2.5 turns to align the matchmarks.

NOTICE:

Do not turn the spiral cable sub-assembly by the airbag wire harness.


HINT:

The spiral cable sub-assembly can be rotated approximately 2.5 turns to both the left and right from the center position.



Hide 45107 6.INSTALL HORN BUTTON WIRE SUB-ASSEMBLY (w/o Steering Pad Switch)

a.

Connect the horn button wire sub-assembly to the spiral cable assembly.


Hide 45286B 7.INSTALL UPPER STEERING COLUMN COVER

Hide 45287 8.INSTALL LOWER STEERING COLUMN COVER

Hide 45100 9.INSTALL STEERING WHEEL ASSEMBLY

Hide 10.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)

Hide 45130 13.INSPECT HORN BUTTON ASSEMBLY

a.

With the horn button assembly installed to the vehicle, perform a visual check. If there are any defects as mentioned below, replace the horn button assembly with a new one:

Cuts, minute cracks or marked discoloration on the horn button assembly top surface or in the grooved portion.


b.

Make sure that the horn sounds.

If the horn does not sound, inspect the horn system.

Click hereVehicle Exterior>HORN>HORN SYSTEM>PROBLEM SYMPTOMS TABLE