Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2016.10–2018.05
RM32K0E _51 Engine / Hybrid System _059620 HYBRID / BATTERY CONTROL _0292486 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P056014  System Voltage (BATT) Circuit Short to Ground or Open  


DESCRIPTION

Auxiliary battery power is supplied to the BATT terminal of the hybrid vehicle control ECU in order to store DTCs and freeze frame data. Even if the power switch is turned off, back-up power is supplied.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P056014 System Voltage (BATT) Circuit Short to Ground or Open Malfunction in the hybrid vehicle control ECU back-up power source circuit
(1 trip detection logic)
·

Wire harness or connector

·

Hybrid vehicle control ECU

·

Fuse


Comes on Master Warning Light:
Comes on

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

With power switch on (IG) and wait for 5 seconds or more.

7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

A394802E01
0.76,2.229 3.365,2.427 2.604,0.198 10 false Auxiliary Battery 0.563,1.5 1.417,1.76 0.854,0.26 10 false BATT-MAIN 1.958,1.26 2.813,1.521 0.854,0.26 10 false J/B-B 3.323,1.26 4.375,1.51 1.052,0.25 10 false ECU-B NO. 2 5.354,1.104 5.719,1.323 0.365,0.219 10 false F3 5.354,2.177 5.719,2.396 0.365,0.219 10 false F2 5.396,0.917 5.76,1.135 0.365,0.219 10 false 3 5.396,1.99 5.76,2.208 0.365,0.219 10 false 6 5.698,1.104 6.219,1.323 0.521,0.219 10 false BATT 5.698,2.177 6.063,2.417 0.365,0.24 10 false E1 5.563,2.792 6.521,3.229 0.958,0.438 10 false Hybrid Vehicle Control ECU 3.479,1.031 3.844,1.25 0.365,0.219 10 false 1 3.917,1.021 4.281,1.24 0.365,0.219 10 false 2 1.885,1.021 2.25,1.24 0.365,0.219 10 false 1 2.323,1.021 2.698,1.219 0.375,0.198 10 false 2

PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)
a.

Check the connector connections and contact pressure of the relevant terminals for the hybrid vehicle control ECU connectors.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

A394800C01
0.042,0.125 0.271,0.313 0.229,0.188 12 true *A 3.594,0.135 3.875,0.406 0.281,0.271 12 false *B
*A for LHD *B for RHD


OK:

The connectors are connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - ECU-B NO. 2 FUSE)

NG

CONNECT SECURELY

2.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - ECU-B NO. 2 FUSE)
a.

Turn the power switch off.


b.
A389500C01
1.802,0.833 2.302,1.083 0.5,0.25 2.375,0.833 2.875,1.083 0.5,0.25 1.667,2.417 1.813,1.719 true 2.917,2.417 2.708,1.719 true 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a 1.573,2.479 1.885,2.635 0.313,0.156 10 false E1 2.833,2.49 3.396,2.656 0.563,0.167 10 false BATT 1.979,0.865 2.313,1.031 0.333,0.167 10 false F2 2.542,0.865 2.875,1.031 0.333,0.167 10 false F3
*a Component with harness connected
(Hybrid Vehicle Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F3-3 (BATT) - F2-6 (E1) Power switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

3.CHECK FUSE (ECU-B NO. 2)
3.CHECK FUSE (ECU-B NO. 2)
a.
A394795C01
1.635,1.917 2.052,2.333 true 0.094,0.073 0.406,0.229 0.313,0.156 10 false *1 2.125,2.229 2.438,2.385 0.313,0.156 10 false *2
*1 Instrument Panel Junction Block Assembly
*2 ECU-B NO. 2 Fuse


Remove the ECU-B NO. 2 fuse from the instrument panel junction block assembly.


b.

Check if there is an open circuit in the ECU-B NO. 2 fuse in the instrument panel junction block assembly.

OK:

There is no open circuit in the ECU-B NO. 2 fuse.



c.

Install the ECU-B NO. 2 fuse.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ECU-B NO. 2 FUSE - BATTERY TERMINAL)

NG

REPLACE FUSE (ECU-B NO. 2)

4.CHECK HARNESS AND CONNECTOR (ECU-B NO. 2 FUSE - BATTERY TERMINAL)
a.
A394796C01
0.104,0.083 0.417,0.24 0.313,0.156 10 false *1 1.302,2.427 1.615,2.583 0.313,0.156 10 false *a
*1 Instrument Panel Junction Block Assembly
*a ECU-B NO. 2 Fuse Holder


Remove the ECU-B NO. 2 fuse from the instrument panel junction block assembly.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Disconnect the cable from the positive (+) auxiliary battery terminal.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (ECU-B NO. 2 fuse holder) - Auxiliary battery positive (+) cable Power switch off Below 1 Ω
1 (ECU-B NO. 2 fuse holder) - Body ground Power switch off 10 kΩ or higher



e.

Connect the cable to the positive (+) auxiliary battery terminal.


f.

Connect the cable to the negative (-) auxiliary battery terminal.


g.

Install the ECU-B NO. 2 fuse.


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (ECU-B NO. 2 FUSE - HYBRID VEHICLE CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (ECU-B NO. 2 FUSE - HYBRID VEHICLE CONTROL ECU)
a.

Remove the ECU-B NO. 2 fuse from the instrument panel junction block assembly.


b.

Disconnect the hybrid vehicle control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

A394797C01
5.708,0.417 6.208,0.667 0.5,0.25 6.458,2.292 6.042,1.875 true 0.25,0.167 0.563,0.323 0.313,0.156 10 false *1 5.885,0.438 6.208,0.688 0.323,0.25 10 false F3 3.833,0.167 4.146,0.323 0.313,0.156 10 false *a 1.198,1.917 1.49,2.115 0.292,0.198 10 false *b 6.313,2.302 6.781,2.51 0.469,0.208 10 false BATT
*1 Instrument Panel Junction Block Assembly - -
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b ECU-B NO. 2 Fuse Holder


Standard Resistance:
Tester Connection Condition Specified Condition
2 (ECU-B NO. 2 fuse holder) - F3-3 (BATT) Power switch off Below 1 Ω



d.

Reconnect the hybrid vehicle control ECU connector.


e.

Install the ECU-B NO. 2 fuse.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR