Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2016.10–2018.05
RM32K0E _51 Engine / Hybrid System _059620 HYBRID / BATTERY CONTROL _0292486 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P300016  Hybrid/EV Battery Control System Circuit Voltage Below Threshold  


DESCRIPTION

The hybrid vehicle control ECU alerts the driver and performs fail-safe control based on error signals received from the battery voltage sensor.

This DTC is stored if the HV battery is discharged excessively or the hybrid control system malfunctions.

HINT:

If the HV battery voltage has dropped due to a malfunction in other components such as the inverter with converter assembly or the hybrid vehicle transaxle assembly, recharging the HV battery will be able to restore the voltage. If the HV battery voltage has dropped excessively after the vehicle was left for a long time, the HV battery will need to be replaced.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P300016 Hybrid/EV Battery Control System Circuit Voltage Below Threshold Malfunction is received from the battery voltage sensor:
Voltage of a battery block drops drastically.
(1 trip detection logic)
·

Engine

·

Hybrid vehicle transaxle assembly

·

HV battery


Does not come on Master Warning Light:
Comes on

Related Data List
DTC No. Data List
P300016
·

Hybrid Battery Block 1 to 9 Voltage

·

Hybrid Battery SOC

·

Hybrid Battery Voltage

·

Hybrid Battery Current

·

Engine Speed



CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Turn the power switch on (READY) with shift lever in P.

7.

Wait until the engine starts and then stops.

8.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

9.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




CAUTION / NOTICE / HINT

CAUTION:
·
A358021C02
0.531,4.146 0.844,4.344 0.313,0.198 10 false *a 2.74,4.146 3.052,4.344 0.313,0.198 10 false *b
*a Dealer
*b Battery Collection Agent


When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

-

Accidents such as electric shock may result if the HV battery is disposed of improperly or abandoned. Therefore, make sure to return all HV batteries through an authorized collection agent.



·
A358020

After removing the HV battery, keep it away from water. Exposure to water may cause the HV battery to produce heat, resulting in a fire.



HINT:
·

Thoroughly interview the customer as DTC P300016 may be stored if the SOC drops due to the vehicle being left with the shift lever in N for a long time or running out of fuel.

·

When the engine cannot be started, DTC P300016 may be stored because the HV battery cannot be charged.



PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
P300016 or P300000 only is output. A
DTCs other than P300016 or P300000 are also output. B


HINT:

If the HV battery voltage has dropped due to a malfunction in other components such as the inverter with converter assembly or the hybrid vehicle transaxle assembly, recharge the HV battery and then repair the malfunctioning part.



e.

Turn the power switch off.



A

2.CHECK DTC OUTPUT (ENGINE)

B

2.CHECK DTC OUTPUT (ENGINE)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Check for DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
No DTCs are output. A
DTCs are output. B



e.

Turn the power switch off.



A

3.CHECK ENGINE START

B

3.CHECK ENGINE START
a.

Turn the power switch on (READY).


b.

Check if the engine starts.

NOTICE:

Do not turn the power switch on (READY) repeatedly after duplicating the problem symptom indicated by DTC P300016 and clearing the DTCs. This may cause another problem to occur.


HINT:

Depressing the accelerator pedal with shift lever in P will cause the engine to start.


Result:
Result Proceed to
The engine does not start. A
The engine starts. B



c.

Turn the power switch off.



A

4.CHECK CRANKSHAFT PULLEY REVOLUTION (P POSITION)

B

LEAVE VEHICLE WITH SHIFT LEVER IN P, AND CHARGE HV BATTERY BY IDLING UNTIL IDLING STOPS

4.CHECK CRANKSHAFT PULLEY REVOLUTION (P POSITION)
a.

Make sure that the shift lever is in P position.


b.

Lift up the vehicle.


c.

Turn the crankshaft pulley using hand tools to check if the crankshaft can rotate smoothly.

CAUTION:

Do not turn the power switch on (READY) while performing this inspection. Be sure to turn the power switch off before performing this inspection, to prevent the engine from starting.


NOTICE:

Engine compression causes resistance when turning the crankshaft pulley. Check if the crankshaft rotates smoothly (or if it is locked) by manually applying sufficient torque to turn the crankshaft pulley. The torque required to turn the crankshaft pulley should be the same as for a known good vehicle of the same type.


Result:
Result Proceed to
The crankshaft rotates smoothly. A
The crankshaft does not rotate smoothly. B



d.

Lower the vehicle.



A

5.CHECK HV BATTERY

B

6.CHECK CRANKSHAFT PULLEY REVOLUTION (N POSITION)
5.CHECK HV BATTERY
a.

Turn the power switch off.


b.

Wait 10 minutes or more.


c.

Connect the GTS to the DLC3.


d.

Turn the power switch on (IG).


e.

Enter the following menus: Powertrain / Hybrid Control / Data List / Hybrid Battery Block 1 to 9 Voltage.

Powertrain > Hybrid Control > Data List
Tester Display
Hybrid Battery Block 1 Voltage
Hybrid Battery Block 2 Voltage
Hybrid Battery Block 3 Voltage
Hybrid Battery Block 4 Voltage
Hybrid Battery Block 5 Voltage
Hybrid Battery Block 6 Voltage
Hybrid Battery Block 7 Voltage
Hybrid Battery Block 8 Voltage
Hybrid Battery Block 9 Voltage
50003 397 161,162,163,164,165,166,167,168,169

f.

Read the Data List.

Result:
Result Proceed to
Any of "Hybrid Battery Block 1, 2, 8, 9 Voltage" is 12.0 V or less, or any of "Hybrid Battery Block 3, 4, 5, 6, 7 Voltage" is 24.0 V or less A
Other than above B



g.

Turn the power switch off.



A

B

10.CLEAR DTC
6.CHECK CRANKSHAFT PULLEY REVOLUTION (N POSITION)
a.

Lift up the vehicle.


b.

Turn the power switch on (IG).


c.

Depress the brake pedal and move the shift lever to N.


d.

Turn the crankshaft pulley using hand tools to check if the crankshaft can rotate smoothly.

CAUTION:

Do not turn the power switch on (READY) while performing this inspection. Be sure to turn the power switch on (IG) before performing this inspection, to prevent the engine from starting.


NOTICE:

Engine compression causes resistance when turning the crankshaft pulley. Check if the crankshaft rotates smoothly (or if it is locked) by manually applying sufficient torque to turn the crankshaft pulley. The torque required to turn the crankshaft pulley should be the same as for a known good vehicle of the same type.


Result:
Result Proceed to
The crankshaft does not rotate smoothly. A
The crankshaft rotates smoothly. B



e.

Lower the vehicle.


f.

Turn the power switch off.



A

7.REPAIR OR REPLACE ENGINE

B

11.REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY
7.REPAIR OR REPLACE ENGINE
Result:
Proceed to
NEXT



NEXT

8.CHECK ENGINE START
8.CHECK ENGINE START
a.

Turn the power switch on (READY).


b.

Check if the engine starts.

NOTICE:

Do not turn the power switch on (READY) repeatedly after duplicating the problem symptom indicated by DTC P300016 and clearing the DTCs. This may cause another problem to occur.


HINT:

Depressing the accelerator pedal with shift lever in P will cause the engine to start.


Result:
Result Proceed to
The engine does not start. A
The engine starts. B



c.

Turn the power switch off.



A

9.CHECK HV BATTERY

B

LEAVE VEHICLE WITH SHIFT LEVER IN P, AND CHARGE HV BATTERY BY IDLING UNTIL IDLING STOPS

9.CHECK HV BATTERY
a.

Turn the power switch off.


b.

Wait 10 minutes or more.


c.

Connect the GTS to the DLC3.


d.

Turn the power switch on (IG).


e.

Enter the following menus: Powertrain / Hybrid Control / Data List / Hybrid Battery Block 1 to 9 Voltage.

Powertrain > Hybrid Control > Data List
Tester Display
Hybrid Battery Block 1 Voltage
Hybrid Battery Block 2 Voltage
Hybrid Battery Block 3 Voltage
Hybrid Battery Block 4 Voltage
Hybrid Battery Block 5 Voltage
Hybrid Battery Block 6 Voltage
Hybrid Battery Block 7 Voltage
Hybrid Battery Block 8 Voltage
Hybrid Battery Block 9 Voltage
50003 397 161,162,163,164,165,166,167,168,169

f.

Read the Data List.

Result:
Result Proceed to
Any of "Hybrid Battery Block 1, 2, 8, 9 Voltage" is 12.0 V or less, or any of "Hybrid Battery Block 3, 4, 5, 6, 7 Voltage" is 24.0 V or less A
Other than above B



g.

Turn the power switch off.



A

B

14.CLEAR DTC
10.CLEAR DTC

NEXT

CHARGE HV BATTERY (ABOUT 10 MINUTES)

11.REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

NEXT

12.CHECK ENGINE START
12.CHECK ENGINE START
a.

Turn the power switch on (READY).


b.

Check if the engine starts.

NOTICE:

Do not turn the power switch on (READY) repeatedly after duplicating the problem symptom indicated by DTC P300016 and clearing the DTCs. This may cause another problem to occur.


HINT:

Depressing the accelerator pedal with shift lever in P will cause the engine to start.


Result:
Result Proceed to
The engine does not start. A
The engine starts. B



c.

Turn the power switch off.



A

13.CHECK HV BATTERY

B

LEAVE VEHICLE WITH SHIFT LEVER IN P, AND CHARGE HV BATTERY BY IDLING UNTIL IDLING STOPS

13.CHECK HV BATTERY
a.

Turn the power switch off.


b.

Wait 10 minutes or more.


c.

Connect the GTS to the DLC3.


d.

Turn the power switch on (IG).


e.

Enter the following menus: Powertrain / Hybrid Control / Data List / Hybrid Battery Block 1 to 9 Voltage.

Powertrain > Hybrid Control > Data List
Tester Display
Hybrid Battery Block 1 Voltage
Hybrid Battery Block 2 Voltage
Hybrid Battery Block 3 Voltage
Hybrid Battery Block 4 Voltage
Hybrid Battery Block 5 Voltage
Hybrid Battery Block 6 Voltage
Hybrid Battery Block 7 Voltage
Hybrid Battery Block 8 Voltage
Hybrid Battery Block 9 Voltage
50003 397 161,162,163,164,165,166,167,168,169

f.

Read the Data List.

Result:
Result Proceed to
Any of "Hybrid Battery Block 1, 2, 8, 9 Voltage" is 12.0 V or less, or any of "Hybrid Battery Block 3, 4, 5, 6, 7 Voltage" is 24.0 V or less A
Other than above B



g.

Turn the power switch off.



A

B

15.CLEAR DTC
14.CLEAR DTC

NEXT

CHARGE HV BATTERY (ABOUT 10 MINUTES)

15.CLEAR DTC

NEXT

CHARGE HV BATTERY (ABOUT 10 MINUTES)