Home › Drivetrain › P610 (HYBRID TRANSMISSION / TRANSAXLE) › HYBRID VEHICLE TRANSAXLE › 2016.10–2019.09
RM32K0E _52 Drivetrain _059722 P610 HYBRID TRANSMISSION / TRANSAXLE _0292760 HYBRID VEHICLE TRANSAXLE A

P610 HYBRID TRANSMISSION / TRANSAXLE  HYBRID VEHICLE TRANSAXLE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during hybrid vehicle transaxle assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Simple intelligent parking assist system*1
Toyota parking assist-sensor system*1
Pre-crash safety system
Initialize back door lock Power door lock control system (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) registration MIL comes on (Click here)
for SFI system
·

Replacement of throttle body assembly

·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Front wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


for Initialization:(Click here)
for Calibration:(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Initialize headlight ECU sub-assembly LH Automatic headlight beam level control system (Click here)
Replacement of hybrid vehicle transaxle assembly
·

Resolver learning

·

Initialize resolver


·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)
Replacement of inverter with converter assembly Resolver learning


CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.

·
A344783

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

·
A346363C01
2.219,0.813 2.646,0.813 false 2.698,0.729 3.01,0.927 0.313,0.198 10 false *a
*a An Object Exceeding Weight Limit of Engine Lifter


The engine assembly with hybrid vehicle transaxle assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.



PROCEDURE

Hide 1. PERFORM RESOLVER INITIALIZATION

NOTICE:

If it is necessary to replace the hybrid vehicle transaxle assembly, make sure to perform resolver initialization before starting work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM>UTILITY


Hide 2.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

Hide 82121 4.DISCONNECT ENGINE WIRE

a.

Disconnect the motor revolution sensor wire connector.

C365164C01
2.531,1.521 2.74,1.719 0.208,0.198 10 true *a 1.833,1.385 2.031,1.573 0.198,0.188 10 true *b 2.271,0.5 2.458,0.688 0.188,0.188 10 true *c
*a Motor Revolution Sensor Wire Connector *b Shift Lever Position Sensor
*c Motor Temperature Sensor Connector - -



b.

Disconnect the shift lever position sensor connector.

NOTICE:
C438726

After disconnecting the engine wire, cover the connector of the shift lever position sensor with tape (non-residue type) or equivalent to prevent the entry of foreign matter or water.



c.

Disconnect the motor temperature sensor connector.


d.

Remove the 2 bolts.


e.

Disengage the 2 clamps to disconnect the engine wire from the hybrid vehicle transaxle assembly.


Hide 821H2 5.DISCONNECT HV AIR CONDITIONING WIRE

a.
C343174

Remove the bolt.


b.

Disengage the guide to disconnect the HV air conditioning wire from the hybrid vehicle transaxle assembly.


Hide 28193 6.REMOVE STARTER HOLE INSULATOR

a.
C343175

Remove the 2 bolts and starter hole insulator from the engine assembly.


Hide 11363A 7.REMOVE FLYWHEEL HOUSING SIDE COVER

a.
C343176

Remove the flywheel housing side cover from the engine assembly.


Hide 8.REMOVE ENGINE ASSEMBLY

a.
C343177

Remove the 7 bolts and engine assembly from the hybrid vehicle transaxle assembly.

NOTICE:
·

To avoid damaging the knock pins, do not pry between the hybrid vehicle transaxle assembly and engine assembly.

·

To prevent the splines of the transmission input damper assembly from becoming misaligned, do not allow the hybrid vehicle transaxle assembly to hit the transmission input damper assembly during hybrid vehicle transaxle assembly removal and installation.




Hide 51201 9.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.
C354263

Remove the bolt and front suspension crossmember sub-assembly from the No. 2 engine moving control rod.


Hide 12364B 10.REMOVE NO. 2 ENGINE MOVING CONTROL ROD

a.
C343179

Remove the 4 bolts and No. 2 engine moving control rod from the hybrid vehicle transaxle assembly.


Hide G125A 12.REMOVE MOTOR COOLING COOLER

a.
C366449

Slide the clip and disconnect the No. 1 motor cooling hose from the No. 1 motor cooling pipe.


b.
C365165

Remove the bolt and No. 1 oil cooler tube clamp from the hose bracket.


c.

Remove the union bolt and gasket to disconnect the No. 2 motor cooling pipe from the hybrid vehicle transaxle assembly.


d.
C365166

Remove the 3 bolts and motor cooling cooler with No. 2 motor cooling pipe from the hybrid vehicle transaxle assembly.

NOTICE:

Make sure not to remove the No. 1 motor cooling hose and No. 2 motor cooling hose from the motor cooling cooler as the motor cooling cooler may be deformed.



Hide G1251B 13.REMOVE NO. 1 MOTOR COOLING PIPE

a.
C365167

Loosen the flare nut of the No. 1 motor cooling pipe and disconnect the No. 1 motor cooling pipe from the union.


b.
C365168

Remove the bolt, No. 1 oil cooler tube clamp and No. 1 motor cooling pipe from the hose bracket.


Hide 44781E 14.REMOVE HOSE BRACKET

a.
C365169

Remove the 2 bolts and hose bracket from the hybrid vehicle transaxle assembly.


Hide 33823 15.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.
C365170

Remove the 2 bolts and No. 1 transmission control cable bracket from the hybrid vehicle transaxle assembly.


Hide 16.REMOVE WIRE HARNESS CLAMP BRACKET

a.
C365171

Remove the 2 bolts and 2 wire harness clamp brackets from the hybrid vehicle transaxle assembly.


Hide 17.REMOVE TRANSAXLE HOUSING PLUG

a.
C344932

Remove the transaxle housing plug and gasket from the hybrid vehicle transaxle assembly.