Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2016.10–2019.09
RM32K0E _51 Engine / Hybrid System _059620 HYBRID / BATTERY CONTROL _0292486 HYBRID CONTROL SYSTEM J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  Brake Override System  


DESCRIPTION

When the vehicle is being driven with the accelerator pedal depressed, depressing the brake pedal without releasing the accelerator pedal will activate the brake override system to restrict driving torque. The conditions for activating the brake override system as well as the items that are controlled are explained below.

C280825E22
3.51,3.323 5.438,3.688 1.927,0.365 10 false Hybrid Vehicle Control ECU 2.74,2.917 3.677,3.115 0.938,0.198 10 false Vehicle Speed 0.469,3.302 2.49,3.51 2.021,0.208 10 false Skid Control ECU Assembly 0.198,1.219 2.5,1.448 2.302,0.229 10 false Accelerator Pedal Sensor Assembly 2.5,0.99 3.667,1.427 1.167,0.438 10 false Actual accelerator opening 2.594,1.948 3.583,2.313 0.99,0.365 10 false Braking torque 5.49,1.365 7.021,1.604 1.531,0.24 10 false Meter display request 5.458,2.354 6.833,2.896 1.375,0.542 10 false Requested accelerator torque 0.198,0.219 2.073,0.406 1.875,0.188 10 false Brake Override System:

Activation Conditions:
·

The accelerator pedal and brake pedal are depressed at the same time.

NOTICE:

Brake override control may not be performed depending on the relationship between accelerator opening and vehicle speed.




Items Controlled:
·

Controls driving force

HINT:
·

When the control is operating, requested accelerator torque is controlled in accordance with the brake pedal stroke.

·

When the driving force is reduced to a specified level because the accelerator pedal and brake pedal are depressed at the same time, an indicator is displayed on the meter. (Operation of the system can be confirmed when the indicator is displayed on the meter.)





Deactivation Conditions:
·

The accelerator pedal or brake pedal is released.



CAUTION / NOTICE / HINT

Inspection Method

Drive at 10 km/h (6 mph), depress the accelerator pedal by 1/2 to 3/4 and keep it in that position. Under these conditions, if driving torque is controlled when the brake pedal is depressed by the left foot of the driver, it can be confirmed that the brake override system has operated.

CAUTION:

Perform this road test only in an appropriate safe location, in accordance with all local laws.

Pay careful attention to the surroundings when performing the road test.


HINT:

The brake override system restricts driving torque if the brake pedal is depressed when driving with the accelerator pedal depressed. If a customer reports experiencing a loss of power (driving torque) after the accelerator and brake pedals have both been intentionally depressed, explain that this is not a malfunction, and depressing both the accelerator and brake pedals at the same time should be avoided.



PROCEDURE

1.CHECK DTC OUTPUT (HEALTH CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: System Select / Health Check.


e.

Check for DTCs.

Result:
Result Proceed to
No DTCs are output. A
DTCs are output. B



f.

Turn the power switch off.



A

2.READ VALUE USING GTS (MASTER CYLINDER CONTROL TORQUE)

B

GO TO DTC CHART

2.READ VALUE USING GTS (MASTER CYLINDER CONTROL TORQUE)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Hybrid Control / Data List / Master Cylinder Control Torque.

Powertrain > Hybrid Control > Data List
Tester Display
Master Cylinder Control Torque
50003 397 89
Powertrain > Hybrid Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Master Cylinder Control Torque Braking torque equivalent to master cylinder brake fluid pressure Total braking torque Master cylinder brake fluid pressure control torque = hydraulic brake control torque + rear regenerative brake torque - Brake pedal depressed:
Changes with the brake pedal pressure
Master cylinder pressure sensor
Result:
Result Proceed to
Display changes according to brake pedal depression force. A
Display does not change according to brake pedal depression force. B



e.

Turn the power switch off.



A

3.READ VALUE USING GTS (ACCELERATOR POSITION SENSOR NO. 1 VOLTAGE %, ACCELERATOR POSITION SENSOR NO. 2 VOLTAGE %)

B

CHECK BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

3.READ VALUE USING GTS (ACCELERATOR POSITION SENSOR NO. 1 VOLTAGE %, ACCELERATOR POSITION SENSOR NO. 2 VOLTAGE %)

OK

4.READ VALUE USING GTS (VEHICLE SPEED)

NG

REPLACE ACCELERATOR PEDAL(W/SENSOR) ROD ASSEMBLY

4.READ VALUE USING GTS (VEHICLE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Hybrid Control / Data List / Vehicle Speed.

Powertrain > Hybrid Control > Data List
Tester Display
Vehicle Speed
50003 397 12

e.

Read the value of "Vehicle Speed" displayed on the GTS.

Standard:
Inspection Condition Specified Condition
Vehicle stopped 0 km/h (0 mph)
Vehicle being driven at a constant speed
(16 to 64 km/h (10 to 40 mph))
No large fluctuations in displayed speed


CAUTION:

Perform this road test only in an appropriate safe location, in accordance with all local laws.


HINT:

Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.



f.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (FR, FL, RR, RL WHEEL SPEED)

NG

GO TO METER / GAUGE SYSTEM (SPEED SIGNAL CIRCUIT)

5.READ VALUE USING GTS (FR, FL, RR, RL WHEEL SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (READY).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List / All Data / FR Wheel Speed, FL Wheel Speed, RR Wheel Speed and RL Wheel Speed.

Chassis > ABS/VSC/TRAC > Data List
Tester Display
FR Wheel Speed
FL Wheel Speed
RR Wheel Speed
RL Wheel Speed
50003 105 1,2,3,4

e.

Read the value of "FR Wheel Speed", "FL Wheel Speed", "RR Wheel Speed" and "RL Wheel Speed" displayed on the GTS.

Standard:
Inspection Condition Specified Condition
Vehicle stopped 0 km/h (0 mph)
Vehicle being driven at a constant speed
(16 to 64 km/h (10 to 40 mph))
No large fluctuations in displayed speed


CAUTION:

Perform this road test only in an appropriate safe location, in accordance with all local laws.


HINT:

Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.



f.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

END

NG