Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2016.10–2019.09
RM32K0E _58 Vehicle Interior _062180 METER / GAUGE / DISPLAY _0304590 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speed Signal Circuit  


DESCRIPTION

The combination meter assembly receives the vehicle speed signal from this circuit. The wheel speed sensors produce an output that varies according to the vehicle speed. The wheel speed sensor output is received by the brake actuator assembly (skid control ECU) which uses this information to create the vehicle speed signal*a. The vehicle speed signal consists of pulses sent to the combination meter assembly from the brake actuator assembly (skid control ECU). To create this signal, 12 V is output from IG2 which is behind a resistor in the combination meter assembly. This voltage is sent to the brake actuator assembly (skid control ECU). The pulse signal is created by switching the transistor in the brake actuator assembly (skid control ECU) on and off, making the voltage on the wire drop to 0 V. A similar system is used for the output of this signal from the combination meter assembly via terminal +S. A voltage of 12 V or 5 V is applied to terminal +S from each ECU or relay that is connected to this terminal. The transistor in the combination meter assembly is controlled by the signal from the brake actuator assembly (skid control ECU). When this transistor is turned on, this transistor makes the voltage supplied by the various ECUs (via their respective internal resistors) drop to 0 V. Each ECU connected to terminal +S of the combination meter assembly controls its respective system based on this pulse signal.

*a: This vehicle speed signal is created by the brake actuator assembly (skid control ECU). There is no actual component that is referred to as the vehicle speed sensor. In addition, for some systems, vehicle speed information may be received via CAN communication.


HINT:

This circuit is used for the systems connected to terminal +S. This signal is not used for combination meter assembly operation. Combination meter assembly components such as the speedometer operate using data received via CAN communication.


WIRING DIAGRAM

C371179E01
0.188,1.333 3.021,1.552 2.833,0.219 10 false Brake Actuator Assembly (Skid Control ECU) 0.427,4.365 0.885,4.563 0.458,0.198 10 false F47 0.188,1.177 0.646,1.375 0.458,0.198 10 false A39 0.208,2.75 0.667,2.948 0.458,0.198 10 false F76 0.26,5.958 0.719,6.156 0.458,0.198 10 false F125 5.156,5.969 5.615,6.167 0.458,0.198 10 false F56 5.094,4.365 5.552,4.563 0.458,0.198 10 false F1 5.094,2.781 5.552,2.979 0.458,0.198 10 false F4 0.198,2.906 3.031,3.125 2.833,0.219 10 false Stereo Component Amplifier Assembly*1 0.417,4.531 2.271,4.75 1.854,0.219 10 false Radio Receiver Assembly*2 0.25,6.125 3.083,6.344 2.833,0.219 10 false Radio and Display Receiver Assembly*3 5.146,6.125 6.521,6.354 1.375,0.229 10 false Auto Wiper ECU 5.094,4.521 6.948,4.927 1.854,0.406 10 false Certification ECU (Smart Key ECU Assembly) 5.083,2.927 6.958,3.188 1.875,0.26 10 false Combination Meter Assembly 0.25,6.833 2.479,7.073 2.229,0.24 10 false *1: for Separate Type Amplifier 0.25,7.25 2.104,7.469 1.854,0.219 10 false *2: for Radio Receiver Type 2.833,6.833 5.469,7.052 2.635,0.219 10 false *3: for Radio and Display Receiver Type 1.719,0.552 2.177,0.75 0.458,0.198 10 false SP1 1.708,2.135 2.167,2.333 0.458,0.198 10 false SPD 1.708,3.729 2.167,3.927 0.458,0.198 10 false SPD 1.698,5.333 2.156,5.531 0.458,0.198 10 false SPD 5.198,5.323 5.656,5.521 0.458,0.198 10 false SPD 5.208,3.729 5.667,3.927 0.458,0.198 10 false SPD 5.208,2.135 5.667,2.333 0.458,0.198 10 false +S 5.198,0.542 5.656,0.74 0.458,0.198 10 false SI 5.823,0.635 6.063,0.833 0.24,0.198 10 false I/F 2.781,2.104 3.24,2.302 0.458,0.198 10 false *1 2.771,3.698 3.229,3.896 0.458,0.198 10 false *2 2.104,0.552 2.406,0.74 0.302,0.188 10 false 11 2.115,2.135 2.417,2.323 0.302,0.188 10 false 11 2.115,3.74 2.417,3.927 0.302,0.188 10 false 17 2.104,5.333 2.406,5.521 0.302,0.188 10 false 17 2.802,5.313 3.26,5.51 0.458,0.198 10 false *3 4.896,5.333 5.198,5.521 0.302,0.188 10 false 24 4.906,3.74 5.208,3.927 0.302,0.188 10 false 19 4.958,2.146 5.26,2.333 0.302,0.188 10 false 6 4.969,0.552 5.271,0.74 0.302,0.188 10 false 5 5.844,2.208 6.083,2.406 0.24,0.198 10 false I/F

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the ECM or certification ECU (smart key ECU assembly) refer to Service Bulletin.

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



PROCEDURE

1.INSPECT ECU TERMINAL VOLTAGE (INPUT VOLTAGE)
a.
E188997C47
0.76,0.479 1.177,0.729 0.417,0.25 1.25,1.531 1.448,1.969 true 1.385,1.979 1.688,2.167 0.302,0.188 10 false +S 0.177,0.188 0.427,0.385 0.25,0.198 10 false *a 0.875,0.521 1.333,0.719 0.458,0.198 10 false F4
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F4-6 (+S) - Body ground Power switch on (IG) 4.5 to 14 V


HINT:

If any of the ECUs specified in the wiring diagram supplies power to the combination meter assembly, the combination meter assembly will output a waveform.



Result:
Proceed to
OK
NG



OK

2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)

NG

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - EACH ECU)
2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)
a.

Reconnect the F4 combination meter assembly connector.


b.
E341942C04
1.5,0.125 1.906,0.354 0.406,0.229 2.146,1.125 2.833,0.49 true 0.167,0.135 0.479,0.292 0.313,0.156 10 false *a 1.573,0.156 2.094,0.448 0.521,0.292 10 false A39 2.885,0.313 3.406,0.604 0.521,0.292 10 false SP1
*a Front view of wire harness connector
(to Brake Actuator Assembly (Skid Control ECU))


Disconnect the brake actuator assembly (skid control ECU) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A39-11 (SP1) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (INPUT WAVEFORM)

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU))
3.INSPECT BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (INPUT WAVEFORM)
a.
B232574C81
1.479,0.469 1.844,0.698 0.365,0.229 2.438,1.948 2.281,1.313 true 0.177,0.156 0.667,0.469 0.49,0.313 10 false *a 2.385,1.99 2.813,2.219 0.427,0.229 10 false SI 2.76,3.646 3.406,3.917 0.646,0.271 10 false GND 1.573,0.49 1.927,0.698 0.354,0.208 10 false F4 0.896,3.76 1.385,4.073 0.49,0.313 10 false A
*a Component with harness connected
(Combination Meter Assembly)


Check the input waveform.

i.

Reconnect the A39 brake actuator assembly (skid control ECU) connector.


ii.

Remove the combination meter assembly with the connector(s) still connected.


iii.

Connect an oscilloscope to terminal F4-5 (SI) and body ground.


iv.

Turn the power switch on (IG).


v.

Turn a wheel slowly.


vi.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Power switch on (IG) wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU))
a.

Disconnect the F4 combination meter assembly connector.


b.

Disconnect the A39 brake actuator assembly (skid control ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F4-5 (SI) - A39-11 (SP1) Always Below 1 Ω
F4-5 (SI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - EACH ECU)
a.

Disconnect the F76 stereo component amplifier assembly connector.*1


b.

Disconnect the F47 radio receiver assembly connector.*2


c.

Disconnect the F125 radio and display receiver assembly connector.*3


d.

Disconnect the F1 certification ECU (smart key ECU assembly) connector.


e.

Disconnect the F56 auto wiper ECU connector.


f.

Measure the resistance according to the value(s) in the table below.

*1: for Separate Type Amplifier

*2: for Radio Receiver Type

*3: for Radio and Display Receiver Type


Standard Resistance:
Tester Connection Condition Specified Condition
F4-6 (+S) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CONFIRM MODEL

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for Separate Type Amplifier A
Except Separate Type Amplifier B



A

7.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (SHORT CIRCUIT IN STEREO COMPONENT AMPLIFIER ASSEMBLY)

B

8.CONFIRM MODEL
7.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (SHORT CIRCUIT IN STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the F76 stereo component amplifier assembly connector.


b.

Reconnect the F47 radio receiver assembly connector.*1


c.

Reconnect the F125 radio and display receiver assembly connector.*2


d.

Reconnect the F1 certification ECU (smart key ECU assembly) connector.


e.

Reconnect the F56 auto wiper ECU connector.


f.

Measure the voltage according to the value(s) in the table below.

*1: for Radio Receiver Type

*2: for Radio and Display Receiver Type


Standard Voltage:
Tester Connection Switch Condition Specified Condition
F4-6 (+S) - Body ground Power switch on (IG) 4.5 to 14 V


HINT:

If the result is as specified, there may be a short circuit in the radio receiver assembly.



Result:
Proceed to
OK
NG



OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

8.CONFIRM MODEL
8.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for Radio Receiver Type A
Except Radio Receiver Type B



A

9.INSPECT RADIO RECEIVER ASSEMBLY (SHORT CIRCUIT IN RADIO RECEIVER ASSEMBLY)

B

10.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (SHORT CIRCUIT IN RADIO AND DISPLAY RECEIVER ASSEMBLY)
9.INSPECT RADIO RECEIVER ASSEMBLY (SHORT CIRCUIT IN RADIO RECEIVER ASSEMBLY)
a.

Disconnect the F47 radio receiver assembly connector.


b.

Reconnect the F1 certification ECU (smart key ECU assembly) connector.


c.

Reconnect the F56 auto wiper ECU connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F4-6 (+S) - Body ground Power switch on (IG) 4.5 to 14 V


HINT:

If the result is as specified, there may be a short circuit in the stereo component amplifier assembly.



Result:
Proceed to
OK
NG



OK

NG

10.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (SHORT CIRCUIT IN RADIO AND DISPLAY RECEIVER ASSEMBLY)
10.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (SHORT CIRCUIT IN RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the F125 radio and display receiver assembly connector.


b.

Reconnect the F1 certification ECU (smart key ECU assembly) connector.


c.

Reconnect the F56 auto wiper ECU connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F4-6 (+S) - Body ground Power switch on (IG) 4.5 to 14 V


HINT:

If the result is as specified, there may be a short circuit in the radio receiver assembly.



Result:
Proceed to
OK
NG



OK

NG

11.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (SHORT CIRCUIT IN CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
11.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (SHORT CIRCUIT IN CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the F1 certification ECU (smart key ECU assembly) connector.


b.

Reconnect the F56 auto wiper ECU connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F4-6 (+S) - Body ground Power switch on (IG) 4.5 to 14 V


HINT:

If the result is as specified, there may be a short circuit in the stereo component amplifier assembly.



Result:
Proceed to
OK
NG



OK

NG

REPLACE AUTO WIPER ECU