Refer to the description for DTC P1AC000.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P1AC000
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P0AFC62 | Hybrid/EV Battery Sensor Module Signal Compare Failure | The difference between the voltage output by detection circuit C and the total of the voltage output by detection circuits A and B exceeds a threshold.
HINT: The battery voltage sensor uses 3 voltage detection circuits (A, B and C) to detect the voltage of the battery blocks. (1 trip detection logic) |
·
Battery voltage sensor ·
HV battery |
Comes on | Master Warning Light:
Comes on |
| P0B3B14 | Hybrid/EV Battery Voltage Sensor "A" Circuit Short to Ground or Open | The battery block voltage detection line has a malfunction and any of the battery block voltages become lower than the specified value (open).
(1 trip detection logic) |
·
Battery voltage sensor ·
HV battery |
Comes on | Master Warning Light:
Comes on |
| P0B4014 | Hybrid/EV Battery Voltage Sensor "B" Circuit Short to Ground or Open | The battery block voltage detection line has a malfunction and any of the battery block voltages become lower than the specified value (open).
(1 trip detection logic) |
·
Battery voltage sensor ·
HV battery |
Comes on | Master Warning Light:
Comes on |
| P0B4514 | Hybrid/EV Battery Voltage Sensor "C" Circuit Short to Ground or Open | The battery block voltage detection line has a malfunction and any of the battery block voltages become lower than the specified value (open).
(1 trip detection logic) |
·
Battery voltage sensor ·
HV battery |
Comes on | Master Warning Light:
Comes on |
| P0B4A14 | Hybrid/EV Battery Voltage Sensor "D" Circuit Short to Ground or Open | The battery block voltage detection line has a malfunction and any of the battery block voltages become lower than the specified value (open).
(1 trip detection logic) |
·
Battery voltage sensor ·
HV battery |
Comes on | Master Warning Light:
Comes on |
| P0B4F14 | Hybrid/EV Battery Voltage Sensor "E" Circuit Short to Ground or Open | The battery block voltage detection line has a malfunction and any of the battery block voltages become lower than the specified value (open).
(1 trip detection logic) |
·
Battery voltage sensor ·
HV battery |
Comes on | Master Warning Light:
Comes on |
| P0B5414 | Hybrid/EV Battery Voltage Sensor "F" Circuit Short to Ground or Open | The battery block voltage detection line has a malfunction and any of the battery block voltages become lower than the specified value (open).
(1 trip detection logic) |
·
Battery voltage sensor ·
HV battery |
Comes on | Master Warning Light:
Comes on |
| P0B5914 | Hybrid/EV Battery Voltage Sensor "G" Circuit Short to Ground or Open | The battery block voltage detection line has a malfunction and any of the battery block voltages become lower than the specified value (open).
(1 trip detection logic) |
·
Battery voltage sensor ·
HV battery |
Comes on | Master Warning Light:
Comes on |
| P0B5E14 | Hybrid/EV Battery Voltage Sensor "H" Circuit Short to Ground or Open | The battery block voltage detection line has a malfunction and any of the battery block voltages become lower than the specified value (open).
(1 trip detection logic) |
·
Battery voltage sensor ·
HV battery |
Comes on | Master Warning Light:
Comes on |
| P0B6314 | Hybrid/EV Battery Voltage Sensor "I" Circuit Short to Ground or Open | The battery block voltage detection line has a malfunction and any of the battery block voltages become lower than the specified value (open).
(1 trip detection logic) |
·
Battery voltage sensor ·
HV battery |
Comes on | Master Warning Light:
Comes on |
| P0B6814 | Hybrid/EV Battery Voltage Sensor "J" Circuit Short to Ground or Open | The battery block voltage detection line has a malfunction and any of the battery block voltages become lower than the specified value (open).
(1 trip detection logic) |
·
Battery voltage sensor ·
HV battery |
Comes on | Master Warning Light:
Comes on |
| P308A13 | Hybrid/EV Battery Voltage Sensor All Circuit Open | The battery block voltage detection line is open (all blocks) or all battery block voltages become lower than the specified value (possibility of open or loosely connected connector).
(1 trip detection logic) |
·
Battery voltage sensor ·
HV battery |
Comes on | Master Warning Light:
Comes on |
Hybrid Battery Block 1 to 9 Voltage values smaller than 2.0 V may not be shown in the Data List because a fail-safe value is substituted.
| DTC No. | Data List |
|---|---|
| P0AFC62 | Hybrid Battery Block 1 to 9 Voltage *1 |
| P0B3B14 | |
| P0B4014 | |
| P0B4514 | |
| P0B4A14 | |
| P0B4F14 | |
| P0B5414 | |
| P0B5914 | |
| P0B5E14 | |
| P0B6314 | |
| P0B6814 | |
| P308A13 | ·
Hybrid Battery Voltage ·
Hybrid Battery Block 1 to 9 Voltage |
*1: Under normal conditions, the values of Hybrid Battery Block 1, 2, 8 and 9 Voltage will be approximately 16 V and Hybrid Battery Block 3, 4, 5, 6 and 7 Voltage will be approximately 32 V.
If there is a short or open in a battery block voltage detection line, the value of Hybrid Battery Block Voltage for the corresponding battery block will be lower than 8 V.
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY
Connect the GTS to the DLC3.
Turn the power switch on (IG) and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for 2 minutes or more.
Turn the power switch on (IG) and turn the GTS on.
With power switch on (IG) and wait for 20 seconds or more.
Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.
Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.
Inspecting the high-voltage system
Disconnecting the low voltage connector of the inverter with converter assembly
Disconnecting the low voltage connector of the HV battery
To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.
After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
| *a | Without waiting for 10 minutes |
After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM>PRECAUTION
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
| *a | Dealer |
| *b | Battery Collection Agent |
When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.
Accidents such as electric shock may result if the HV battery is disposed of improperly or abandoned. Therefore, make sure to return all HV batteries through an authorized collection agent.
After removing the HV battery, keep it away from water. Exposure to water may cause the HV battery to produce heat, resulting in a fire.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check and record any HV system DTCs and freeze frame data.
Read output DTCs.
| Result | Proceed to |
|---|---|
| P0AFC00, P0AFC96 or P308A12 is not output. | A |
| P0AFC00, P0AFC96 or P308A12 is also output. | B |
Turn the power switch off.
A
B
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the No. 1 hybrid battery exhaust duct.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL
Check the connections of the z12 battery voltage sensor connector.
The connector is connected securely and there are no contact problems.
| Result |
|---|
| OK |
| NG |
Install the No. 1 hybrid battery exhaust duct.
OK
NG
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY VOLTAGE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Clear DTCs.
Clear the DTCs and freeze frame data.
Turn the power switch off.
Turn the power switch on (IG) and wait for 10 seconds or more.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Read output DTCs.
| Result | Proceed to |
|---|---|
| Hybrid battery voltage sensor circuit DTCs for this diagnostic procedure are not output. | A |
| Hybrid battery voltage sensor circuit DTCs for this diagnostic procedure are output. | B |
Turn the power switch off.
A
B