Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › BATTERY VOLTAGE SENSOR › 2016.10–2019.09
RM32K0E _51 Engine / Hybrid System _059620 HYBRID / BATTERY CONTROL _0292491 BATTERY VOLTAGE SENSOR A

HYBRID / BATTERY CONTROL  BATTERY VOLTAGE SENSOR  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during battery voltage sensor removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Simple intelligent parking assist system*1
Toyota parking assist-sensor system*1
Pre-collision system
Initialize back door lock Power door lock control system (Click here)

CAUTION:
·
A340386

This vehicle has contains high voltage circuits standardized with orange colored wiring and connectors, so follow the instructions in this manual to perform the procedures correctly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

·

If the correct procedures are not followed according to the instructions in this manual, there is a danger of electric shock from the high voltage circuits.

·
A340358

Be sure to wear insulating gloves when working on high voltage wiring or components.

·

If work is performed without wearing insulating gloves, there is a danger of electric shock.



NOTICE:
·

The type of battery voltage sensor to be used varies depending on the vehicle model.

·
A375908C02
2.135,0.865 2.865,0.865 true 2.917,0.792 3.229,0.99 0.313,0.198 10 false *a
*a Black Label


The type of battery voltage sensor can be confirmed by the color of the label.

·

If the wrong type of battery voltage sensor is installed, the power switch cannot be turned on (READY).

·

After installing the battery voltage sensor, perform the following to check that the power switch can be turned on (READY).

-

Turn the power switch on (READY).

-

Turn the power switch off and wait for 30 seconds or more.

-

Turn the power switch on (READY) again.




PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 6.INSTALL CONNECTOR COVER ASSEMBLY

Hide 8.REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY

Hide 72693 9.REMOVE REAR SEAT CUSHION LOCK HOOK

Hide 67918A 10.REMOVE REAR DOOR SCUFF PLATE LH

Hide 76974F 11.REMOVE REAR UNDER SIDE COVER LH

Hide 67917A 12.REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 76973F 13.REMOVE REAR UNDER SIDE COVER RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 76971G 14.REMOVE REAR UNDER COVER

Hide 71033 15.REMOVE REAR SEAT CUSHION LEG SUB-ASSEMBLY

Hide G9230 16.REMOVE BATTERY COOLING BLOWER ASSEMBLY

Hide G92N4A 17.REMOVE NO. 1 HV BATTERY COVER PANEL RH

Hide 821H1 18.DISCONNECT HV FLOOR UNDER WIRE

Hide G92F1 20.REMOVE NO. 1 HYBRID BATTERY EXHAUST DUCT

Hide G920L 22.REMOVE UPPER NO. 1 HYBRID BATTERY COVER SUB-ASSEMBLY

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A378149

Remove the 5 bolts.

NOTICE:
·

Do not allow foreign matter, such as grease or oil, to adhere to the bolts of the HV battery.

·

To prevent the wire harness from being caught, make sure to bundle the wire harness using insulating tape or equivalent.

·

If the HV battery has been struck or dropped, replace it.




b.
A375899

Move the HV battery toward the front of the vehicle.


c.
A375900C02
1.313,0.042 1.521,0.219 0.208,0.177 10 true *a 1.896,0.052 2.104,0.229 0.208,0.177 10 true *a 2.385,0.146 2.594,0.323 0.208,0.177 10 true *a 2.76,0.354 2.969,0.531 0.208,0.177 10 true *a 3.104,0.594 3.313,0.771 0.208,0.177 10 true *a 0.146,0.25 0.354,0.427 0.208,0.177 10 true *a 2.156,1.667 2.365,1.844 0.208,0.177 10 true *b 1.25,1.917 1.458,2.094 0.208,0.177 10 true *b 0.948,1.615 1.156,1.792 0.208,0.177 10 true *b 0.49,1.385 0.698,1.563 0.208,0.177 10 true *b 0.135,1.115 0.344,1.292 0.208,0.177 10 true *b
*a Bolt
*b Nut


Remove the 6 bolts, 5 nuts and upper No. 1 hybrid battery cover sub-assembly from the HV battery.


Hide G92Q1 23.REMOVE NO. 1 HV BATTERY SHIELD PANEL

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A375901

Disengage the clamp.


b.

Disconnect the battery voltage sensor connector.


c.
A375902

Remove the bolt and 2 nuts.


d.
A375903C03
0.823,1.813 1.073,1.813 1.073,1.813 1.354,1.521 true 2.01,0.354 2.26,0.354 2.26,0.354 2.75,1.031 true 0.563,1.74 0.802,1.917 0.24,0.177 10 true *1 1.74,0.26 1.979,0.438 0.24,0.177 10 true *2
*1 No. 1 HV Battery Shield Panel
*2 No. 2 Hybrid Battery Shield Sub-assembly
V100135

Pull Back


Pull back the No. 2 hybrid battery shield sub-assembly and remove the No. 1 HV battery shield panel from the HV battery.

HINT:

Pull back the No. 2 hybrid battery shield sub-assembly until it is separated from the 2 stud bolts of the No. 1 HV battery shield panel.



Hide 89892A 24.REMOVE BATTERY VOLTAGE SENSOR

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A375904

Disconnect the battery voltage sensor connector.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



b.
A378134

Remove the bolt and battery voltage sensor from the HV battery.

NOTICE:

If the battery voltage sensor has been struck or dropped, replace it.