Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2016.10–2019.09
RM32K0E _57 Power Source / Network _059857 NETWORKING _0293867 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Hybrid Vehicle Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Hybrid Vehicle Control ECU Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Hybrid Vehicle Control" and/or "Hybrid Vehicle Control2" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Hybrid Vehicle Control" and/or "Hybrid Vehicle Control2" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Hybrid Vehicle Control" and/or "Hybrid Vehicle Control2" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Hybrid Vehicle Control ECU Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Hybrid vehicle control ECU branch line or connector

·

Power source circuit of hybrid vehicle control ECU

·

Hybrid vehicle control ECU ground circuit

·

Hybrid vehicle control ECU



WIRING DIAGRAM

for LHD



C366173E03
1.75,0.49 2,0.656 0.25,0.167 10 false 9 1.76,1.042 2.01,1.208 0.25,0.167 10 false 20 1.76,1.583 2.01,1.75 0.25,0.167 10 false 3 1.75,2.115 2,2.281 0.25,0.167 10 false 14 0.344,2.573 0.844,2.74 0.5,0.167 10 false F124 0.344,2.74 2.469,3.073 2.125,0.333 10 false No. 5 Junction Connector 5.594,0.427 5.844,0.594 0.25,0.167 10 false 25 5.594,0.615 5.844,0.781 0.25,0.167 10 false F3 5.594,1.125 5.844,1.292 0.25,0.167 10 false F3 5.583,1.667 5.833,1.833 0.25,0.167 10 false F3 5.594,2.208 5.844,2.375 0.25,0.167 10 false F3 5.583,0.948 5.833,1.115 0.25,0.167 10 false 24 5.573,1.5 5.823,1.667 0.25,0.167 10 false 31 5.583,2.042 5.833,2.208 0.25,0.167 10 false 30 5.906,0.615 6.406,0.781 0.5,0.167 10 false CA1H 5.917,1.146 6.417,1.313 0.5,0.167 10 false CA1L 5.906,1.688 6.406,1.854 0.5,0.167 10 false CA3P 5.917,2.229 6.417,2.396 0.5,0.167 10 false CA3N 5.917,3.271 6.417,3.438 0.5,0.167 10 false MREL 5.917,3.823 6.417,3.99 0.5,0.167 10 false +B1 5.917,4.344 6.417,4.51 0.5,0.167 10 false +B2 5.917,4.896 6.417,5.063 0.5,0.167 10 false BATT 5.917,5.427 6.417,5.594 0.5,0.167 10 false IG2 5.917,5.969 6.417,6.135 0.5,0.167 10 false E12 5.917,6.5 6.417,6.667 0.5,0.167 10 false E01 5.917,7.052 6.417,7.219 0.5,0.167 10 false E02 5.896,7.583 6.396,7.75 0.5,0.167 10 false E1 5.625,3.094 5.875,3.26 0.25,0.167 10 false 6 5.552,3.281 5.969,3.448 0.417,0.167 10 false A48 5.552,3.813 5.969,3.979 0.417,0.167 10 false A48 5.625,3.635 5.875,3.802 0.25,0.167 10 false 4 5.604,4.167 5.854,4.333 0.25,0.167 10 false 1 5.531,4.344 5.948,4.51 0.417,0.167 10 false A49 5.615,4.698 5.865,4.865 0.25,0.167 10 false 3 5.583,4.885 5.833,5.052 0.25,0.167 10 false F3 5.625,5.25 5.875,5.417 0.25,0.167 10 false 3 5.552,5.417 5.969,5.583 0.417,0.167 10 false A49 5.615,5.781 5.865,5.948 0.25,0.167 10 false 4 5.583,7.01 5.833,7.177 0.25,0.167 10 false F3 5.625,6.292 5.875,6.458 0.25,0.167 10 false 5 5.583,6.5 5.833,6.667 0.25,0.167 10 false F2 5.635,6.844 5.885,7.01 0.25,0.167 10 false 5 5.625,7.365 5.875,7.531 0.25,0.167 10 false 6 5.594,7.563 5.844,7.729 0.25,0.167 10 false F2 5.583,5.958 5.833,6.125 0.25,0.167 10 false F3 5.323,7.938 7.156,8.188 1.833,0.25 10 false Hybrid Vehicle Control ECU 3.99,3.948 4.74,4.115 0.75,0.167 10 false PM-IGCT 3.854,5.021 5.104,5.188 1.25,0.167 10 false ECU-B NO. 2 3.792,5.552 5.042,5.719 1.25,0.167 10 false ECU-IG2 NO. 1 1.865,5.396 3.531,5.646 1.667,0.25 10 false from IG2 NO. 1 Relay 1.854,4.854 3.521,5.104 1.667,0.25 10 false from Auxiliary Battery 2.188,3.792 3.354,4.042 1.167,0.25 10 false from IGCT Relay 2.313,3.24 3.229,3.49 0.917,0.25 10 false to IGCT Relay

for RHD



C366172E04
1.75,0.417 2,0.583 0.25,0.167 10 false 2 1.74,1 2.073,1.167 0.333,0.167 10 false 13 1.75,2.031 2.083,2.198 0.333,0.167 10 false 4 1.75,2.594 2.083,2.76 0.333,0.167 10 false 14 0.333,1.448 0.75,1.615 0.417,0.167 10 false F113 0.333,1.604 2.417,1.854 2.083,0.25 10 false No. 2 CAN Junction Connector 0.26,3.073 0.677,3.24 0.417,0.167 10 false F118 0.271,3.25 2.354,3.5 2.083,0.25 10 false No. 5 CAN Junction Connector 5.573,0.365 5.823,0.531 0.25,0.167 10 false 25 5.583,0.542 5.833,0.708 0.25,0.167 10 false F3 5.583,1.083 5.833,1.25 0.25,0.167 10 false F3 5.583,2.156 5.833,2.323 0.25,0.167 10 false F3 5.583,2.688 5.833,2.854 0.25,0.167 10 false F3 5.594,0.906 5.844,1.073 0.25,0.167 10 false 24 5.906,0.542 6.406,0.708 0.5,0.167 10 false CA1H 5.917,1.083 6.417,1.25 0.5,0.167 10 false CA1L 5.917,2.156 6.417,2.323 0.5,0.167 10 false CA3P 5.917,2.688 6.417,2.854 0.5,0.167 10 false CA3N 5.583,1.958 5.833,2.125 0.25,0.167 10 false 31 5.573,2.51 5.823,2.677 0.25,0.167 10 false 30 5.625,3.563 5.875,3.729 0.25,0.167 10 false 6 5.552,3.75 5.969,3.917 0.417,0.167 10 false A48 5.542,4.292 5.958,4.458 0.417,0.167 10 false A48 5.615,4.104 5.865,4.271 0.25,0.167 10 false 4 5.552,4.823 5.969,4.99 0.417,0.167 10 false A49 5.583,4.625 5.833,4.792 0.25,0.167 10 false 1 5.625,5.177 5.875,5.344 0.25,0.167 10 false 3 5.583,5.365 5.833,5.531 0.25,0.167 10 false F3 5.542,5.896 5.958,6.063 0.417,0.167 10 false A49 5.615,5.719 5.865,5.885 0.25,0.167 10 false 3 5.625,6.271 5.875,6.438 0.25,0.167 10 false 4 5.583,6.427 5.833,6.594 0.25,0.167 10 false F3 5.604,6.781 5.854,6.948 0.25,0.167 10 false 5 5.583,6.969 5.917,7.135 0.333,0.167 10 false F2 5.625,7.333 5.875,7.5 0.25,0.167 10 false 5 5.594,7.51 5.844,7.677 0.25,0.167 10 false F3 5.615,7.854 5.865,8.021 0.25,0.167 10 false 6 5.583,8.042 5.917,8.208 0.333,0.167 10 false F2 5.917,3.74 6.417,3.906 0.5,0.167 10 false MREL 5.917,4.313 6.417,4.479 0.5,0.167 10 false +B1 5.917,4.844 6.417,5.01 0.5,0.167 10 false +B2 5.917,5.365 6.417,5.531 0.5,0.167 10 false BATT 5.917,5.906 6.417,6.073 0.5,0.167 10 false IG2 5.917,6.427 6.417,6.594 0.5,0.167 10 false E12 5.917,6.99 6.417,7.156 0.5,0.167 10 false E01 5.917,7.521 6.417,7.688 0.5,0.167 10 false E02 5.917,8.042 6.417,8.208 0.5,0.167 10 false E1 5.396,8.438 7.156,8.688 1.76,0.25 10 false Hybrid Vehicle Control ECU 3.75,6.042 4.917,6.208 1.167,0.167 10 false ECU-IG2 NO. 1 3.781,5.521 4.948,5.688 1.167,0.167 10 false ECU-B NO. 2 3.969,4.458 4.719,4.625 0.75,0.167 10 false PM-IGCT 2.302,3.719 3.469,3.969 1.167,0.25 10 false to IGCT Relay 2.156,4.26 3.323,4.51 1.167,0.25 10 false from IGCT Relay 1.854,5.333 3.354,5.583 1.5,0.25 10 false from Auxiliary Battery 1.844,5.875 3.344,6.125 1.5,0.25 10 false from IG2 NO. 1 Relay

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), turn the cruise control main switch on, turn the LDA main switch on and then drive the vehicle at a speed of 20 km/h (12 mph) or more for approximately 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (HYBRID VEHICLE CONTROL ECU BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the hybrid vehicle control ECU connector.


c.
C366200C01
1.417,0.5 1.917,0.75 0.5,0.25 2.083,2.667 2.26,2.24 true 2.667,2.667 2.521,2.25 true 2.833,1.583 2.521,1.885 true 1.583,2.667 2.281,2.021 true 1.24,2.667 1.854,2.865 0.615,0.198 10 false CA1L 2.917,1.49 3.354,1.688 0.438,0.198 10 false CA1H 2.646,2.708 3.26,2.906 0.615,0.198 10 false CA3P 1.76,2.688 2.375,2.885 0.615,0.198 10 false CA3N 0.167,0.135 0.781,0.333 0.615,0.198 10 false *a 1.594,0.531 2.208,0.729 0.615,0.198 10 false F3
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F3-25 (CA1H) - F3-24 (CA1L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
F3-31 (CA3P) - F3-30 (CA3N) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (HYBRID VEHICLE CONTROL ECU)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the hybrid vehicle control ECU connectors.


b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

C366207C02
4.75,0.417 5.25,0.667 0.5,0.25 1.833,0.417 2.333,0.667 0.5,0.25 4.896,1.208 5.917,0.75 true 1.25,0.802 1.823,1.208 true 0.167,0.167 0.479,0.323 0.313,0.156 10 false *a 1.969,0.448 2.375,0.615 0.406,0.167 10 false A49 4.917,0.438 5.323,0.604 0.406,0.167 10 false F3 1.021,0.646 1.427,0.813 0.406,0.167 10 false IG2 6.01,0.656 6.583,0.823 0.573,0.167 10 false BATT
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
- -


Standard Voltage:
Tester Connection Switch Condition Specified Condition
F3-3 (BATT) - Body ground Power switch off 11 to 14 V
A49-3 (IG2) - Body ground Power switch on (IG) 11 to 14 V



Result:
Result
OK
NG



OK

3.CHECK ECU POWER SOURCE CIRCUIT

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

3.CHECK ECU POWER SOURCE CIRCUIT

Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)