Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2016.10–2019.09
RM32K0E _57 Power Source / Network _059857 NETWORKING _0293867 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Center Airbag Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Center Airbag Sensor Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Airbag" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Airbag" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Airbag" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Center Airbag Sensor Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Airbag sensor assembly main line or connector

·

Power source circuit of airbag sensor assembly

·

Airbag sensor assembly ground circuit

·

Airbag sensor assembly



WIRING DIAGRAM

for LHD


C366184E16
0.104,1.552 0.719,1.75 0.615,0.198 10 false F116 0.094,1.708 2.042,1.927 1.948,0.219 10 false No. 4 CAN Junction Connector 1.625,0.521 1.802,0.719 0.177,0.198 10 false 1 1.615,1.052 1.844,1.25 0.229,0.198 10 false 11 2.24,2.198 3.635,2.448 1.396,0.25 10 false from IG2-NO. 2 Relay 4.448,2.365 5.229,2.573 0.781,0.208 10 false A/BAG-IG2 5.542,0.542 5.771,0.74 0.229,0.198 10 false 13 5.542,1.063 5.771,1.26 0.229,0.198 10 false 22 5.552,2.135 5.781,2.333 0.229,0.198 10 false 21 5.542,2.677 5.771,2.875 0.229,0.198 10 false 25 5.531,3.208 5.76,3.406 0.229,0.198 10 false 26 5.813,0.521 6.292,0.698 0.479,0.177 10 false CANH 5.802,1.292 6.281,1.469 0.479,0.177 10 false CANL 5.792,2.219 6.271,2.396 0.479,0.177 10 false IG2 5.802,2.75 6.281,2.927 0.479,0.177 10 false E1 5.792,3.302 6.271,3.479 0.479,0.177 10 false E2 5.417,3.656 5.719,3.854 0.302,0.198 10 false F70 5.406,3.802 6.979,4.021 1.573,0.219 10 false Airbag Sensor Assembly


for RHD


C366184E17
0.104,1.552 0.719,1.75 0.615,0.198 10 false F115 0.094,1.708 2.042,1.927 1.948,0.219 10 false No. 4 CAN Junction Connector 1.625,0.521 1.802,0.719 0.177,0.198 10 false 1 1.615,1.052 1.844,1.25 0.229,0.198 10 false 12 2.208,2.198 3.604,2.448 1.396,0.25 10 false from IG2-NO. 2 Relay 4.448,2.365 5.229,2.573 0.781,0.208 10 false A/BAG-IG2 5.542,0.542 5.771,0.74 0.229,0.198 10 false 13 5.542,1.063 5.771,1.26 0.229,0.198 10 false 22 5.552,2.135 5.781,2.333 0.229,0.198 10 false 21 5.542,2.677 5.771,2.875 0.229,0.198 10 false 25 5.531,3.208 5.76,3.406 0.229,0.198 10 false 26 5.813,0.521 6.292,0.698 0.479,0.177 10 false CANH 5.802,1.292 6.281,1.469 0.479,0.177 10 false CANL 5.792,2.219 6.271,2.396 0.479,0.177 10 false IG2 5.802,2.75 6.281,2.927 0.479,0.177 10 false E1 5.792,3.302 6.271,3.479 0.479,0.177 10 false E2 5.417,3.656 5.719,3.854 0.302,0.198 10 false F70 5.406,3.802 6.979,4.021 1.573,0.219 10 false Airbag Sensor Assembly


CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), turn the cruise control main switch on, turn the LDA main switch on and then drive the vehicle at a speed of 7 km/h (4 mph) or more for approximately 61 seconds or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (AIRBAG SENSOR ASSEMBLY MAIN LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the airbag sensor assembly connector.


c.
C349835C15
1.438,0.094 1.844,0.333 0.406,0.24 1.448,1.094 1.76,0.563 true 1.271,1.354 0.854,0.958 true 0.083,0.094 0.396,0.292 0.313,0.198 10 false *a 1.833,0.458 2.313,0.698 0.479,0.24 10 false CANH 0.448,0.875 0.927,1.115 0.479,0.24 10 false CANL 1.531,0.115 2.01,0.354 0.479,0.24 10 false F70
*a Front view of wire harness connector
(to Airbag Sensor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F70-13 (CANH) - F70-22 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (AIRBAG SENSOR ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C349835C16
1.438,0.094 1.844,0.333 0.406,0.24 0.906,1.75 1.156,1.479 true 1.771,1.708 1.656,1.469 true 2.229,1.76 1.802,1.458 true 0.083,0.094 0.396,0.292 0.313,0.198 10 false *a 0.625,1.677 1.104,1.917 0.479,0.24 10 false IG2 1.531,0.115 1.813,0.313 0.281,0.198 10 false F70 2.302,1.698 2.781,1.938 0.479,0.24 10 false E2 1.823,1.708 2.302,1.948 0.479,0.24 10 false E1
*a Front view of wire harness connector
(to Airbag Sensor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F70-25 (E1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
F70-26 (E2) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F70-21 (IG2) - Body ground Power switch on (IG) 11 to 14 V



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)