Home › Engine / Hybrid System › 2ZR-FXE (FUEL) › FUEL PUMP › 2016.10–2018.05
RM32K0E _51 Engine / Hybrid System _060063 2ZR-FXE FUEL _0294218 FUEL PUMP A

2ZR-FXE FUEL  FUEL PUMP  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel pump removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Simple intelligent parking assist system*1
Toyota parking assist-sensor system*1
Pre-collision system
Initialize back door lock Power door lock control system (Click here)
Replacement of fuel pump Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

*1: When performing learning using the GTS.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>SIMPLE INTELLIGENT PARKING ASSIST SYSTEM>CALIBRATION

PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2. DISCHARGE FUEL SYSTEM PRESSURE

Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>2ZR-FXE AUXILIARY BATTERY>REMOVAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Hide 4.REMOVE REAR SEAT ASSEMBLY

Hide 73480 5.REMOVE REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH

Hide 73380A 6.REMOVE REAR SEAT INNER BELT ASSEMBLY

Hide 71305A 7.REMOVE CENTER REAR SEATBACK HINGE SUB-ASSEMBLY

a.
A395938

Remove the 2 bolts and center rear seatback hinge sub-assembly from the vehicle body.


Hide 82818G 8.REMOVE NO. 8 WIRING HARNESS PROTECTOR

a.

Remove the No. 8 wiring harness protector from the rear floor service hole cover.


Hide 58325E 9.REMOVE REAR FLOOR SERVICE HOLE COVER

a.
A374588C01
1.333,0.5 1.458,0.198 1.458,0.198 1.583,0.198 true 1.625,0.125 1.833,0.271 0.208,0.146 10 true *a
*a Protective Tape


Using a clip remover with its tip wrapped with protective tape, remove the rear floor service hole cover and butyl tape.


b.
A393829

Disconnect the fuel pump connector.


Hide 77404 10.DISCONNECT FUEL TANK VENT HOSE SUB-ASSEMBLY

a.
A393830

Disconnect the fuel tank vent hose sub-assembly from the fuel suction tube with pump and gauge assembly.

Click hereEngine / Hybrid System>2ZR-FXE (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 77209F 11.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A393831C01
1.167,0.958 1,0.5 true 1.531,2.781 1.281,2.531 false 0.333,1.083 0.5,0.833 true 2.083,2.76 2.333,2.51 false 2.469,3.25 2.833,3.25 false 1,3.75 1.25,3.427 false 2.188,3.417 2.667,3.417 2.667,3.417 2.667,3.563 true 2.188,3.563 2.833,3.563 true 0.833,3.729 1.146,3.885 0.313,0.156 10 false *1 2.865,3.146 3.177,3.302 0.313,0.156 10 false *2 0.833,0.365 1.031,0.552 0.198,0.188 10 true *3 2.365,2.365 2.677,2.521 0.313,0.156 10 false *4 2.865,3.458 3.177,3.615 0.313,0.156 10 false *5 1.104,2.365 1.417,2.521 0.313,0.156 10 false *a 0.156,1.104 0.354,1.292 0.198,0.188 10 true *2
*1 Plate Sub-assembly
*2 Tube Joint Clip
*3 Fuel Tank Main Tube Sub-assembly
*4 Fuel Tube Joint
*5 O-ring
*a Nylon Tube
V100135

Pull off
V100136

Pull off


Remove the tube joint clip, and pull off the fuel tube joint of the fuel tank main tube sub-assembly.

NOTICE:
·

Remove any foreign matter on the fuel tube joint before performing this work.

·

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).

·

Be sure to disconnect the fuel tube joint by hand.

·

Do not bend, twist, pinch or kink the nylon tube.

·

Cover the disconnected fuel tube joint with a plastic bag to prevent damage and contamination.

·

If the fuel tube joint and plate sub-assembly are stuck, push and pull to release them.




Hide 77144 12.REMOVE FUEL PUMP GAUGE RETAINER

a.
A399317C01
0,0 0,0 false
V100135

Front Side


Disengage the claw to remove the No. 1 fuel tube clamp.


b.

Remove the fuel pump gauge retainer.

i.
A374375C01
0.99,0.281 1.521,0.281 true 2.604,0.604 2.781,0.604 true 1.958,1.125 2.5,1.125 true 1.958,2.042 1.958,1.604 true 0.854,3.094 1.625,3.094 true 1.667,3.01 1.833,3.188 0.167,0.177 10 true *a 2.823,0.531 3.021,0.688 0.198,0.156 10 true *b 1.885,2.042 2.083,2.208 0.198,0.167 10 true *c 0.833,0.198 1.01,0.354 0.177,0.156 10 true *d 2.542,1.052 2.719,1.208 0.177,0.156 10 true *d
*a Insertion Point
*b SST (Plate)
*c SST (Claw)
*d SST (Bolt)


Temporarily install SST (plate) and SST (claw) to the fuel pump gauge retainer.

SST
09808-01071  
09808-14031  (09808-01030, 09808-01090)

HINT:

Securely insert the ends of SST (claw) into the insertion points in the fuel pump gauge retainer.



ii.

While firmly pressing SST (claw) into the insertion points in the fuel pump gauge retainer, tighten SST (bolt).


iii.
A374376C01
0.813,0.25 0.969,0.25 0.969,0.25 1.188,0.813 true 1.625,0.385 1.729,0.198 1.729,0.198 1.823,0.198 false 1.635,2.292 2.24,2.292 true 1.208,0.146 1.365,0.146 1.365,0.146 1.563,0.51 true 1.865,1.135 2.375,1.135 true 0.635,0.156 0.948,0.313 0.313,0.156 10 false *a 1.865,0.115 2.177,0.271 0.313,0.156 10 false *b 1.458,2.198 1.771,2.354 0.313,0.156 10 false *c 2.406,1.042 2.625,1.219 0.219,0.177 10 true *d 1.031,0.052 1.25,0.229 0.219,0.177 10 false *d
*a SST (Handle)
*b SST (Plate)
*c SST (Claw)
*d SST (Bolt)


Install SST (handle) to SST (plate).

SST
09808-01071  
09808-14031  (09808-01010, 09808-01030, 09808-01090)


iv.

Lightly press down on SST to prevent it from separating from the fuel pump gauge retainer. While pressing down on SST, rotate SST (handle) slowly to loosen the fuel pump gauge retainer.

NOTICE:
·

Do not use any tools other than specified in this operation as this may result in damage to the fuel pump gauge retainer or the fuel tank assembly.

·

Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.

·

Make sure to rotate SST (handle) horizontally. If it is rotated at an angle, SST may come off.

·

Do not spin SST too fast or use an impact wrench as this may result in damage to components.

·

If SST comes off of the fuel pump gauge retainer, loosen SST (bolt) and reinstall SST.




v.

While pressing down on the fuel suction tube with pump and gauge assembly, remove the fuel pump gauge retainer.



Hide 77020A 13.REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

a.

Remove the fuel suction tube with pump and gauge assembly from the fuel tank assembly.

NOTICE:

Be careful not to bend the arm of the fuel sender gauge assembly.



b.
A374377

Remove the fuel suction tube set gasket from the fuel tank assembly.