Home › Engine / Hybrid System › 2ZR-FXE (EMISSION CONTROL) › EGR COOLER › 2016.10–2019.09
RM32K0E _51 Engine / Hybrid System _060064 2ZR-FXE EMISSION CONTROL _0294227 EGR COOLER A

2ZR-FXE EMISSION CONTROL  EGR COOLER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during EGR pipe with cooler sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Simple intelligent parking assist system*1
Toyota parking assist-sensor system*1
Pre-collision system
Initialize back door lock Power door lock control system (Click here)
Replacement of inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) registration MIL comes on (Click here)
·

Replacement of EGR valve assembly

·

Gas leak from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

*1: When performing learning using the GTS.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>SIMPLE INTELLIGENT PARKING ASSIST SYSTEM>CALIBRATION

PROCEDURE

Hide 16671 1.REMOVE FLOW SHUTTING VALVE (WATER VALVE)

Hide 16261 3.DISCONNECT WATER BY-PASS HOSE

a.
A377758

Slide the clip and disconnect the water by-pass hose from the EGR valve assembly.


Hide 87245A 4.DISCONNECT INLET HEATER WATER HOSE A

a.
A377707

Slide the clip and disconnect the inlet heater water hose A from the EGR pipe with cooler sub-assembly.


Hide 16281 5.DISCONNECT NO. 4 WATER BY-PASS HOSE

a.
A377709

Slide the clip and disconnect the No. 4 water by-pass hose from the EGR pipe with cooler sub-assembly.


Hide 25601L 6.REMOVE EGR PIPE WITH COOLER SUB-ASSEMBLY

a.
A377699

Disconnect the EGR valve assembly connector.


b.
A377711

Remove the 2 nuts and disconnect the EGR pipe with cooler sub-assembly from the exhaust manifold (TWC: Front Catalyst).


c.
A377713C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the bolt and 2 nuts and disconnect the EGR pipe with cooler sub-assembly with the EGR valve assembly from the cylinder head sub-assembly and camshaft housing sub-assembly.


d.
A377714

Using an E8 "TORX" socket wrench, remove the 2 stud bolts from the cylinder head sub-assembly and camshaft housing sub-assembly.

HINT:

If a stud bolt is deformed or the threads are damaged, replace it.



e.
A377759

Remove the EGR pipe with cooler sub-assembly with the EGR valve assembly.


f.
A377712

Remove the EGR cooler gasket from the EGR pipe with cooler sub-assembly.


g.
A377715

Slide the clip and disconnect the No. 6 water by-pass hose from the EGR pipe with cooler sub-assembly.


h.
A377717

Remove the 2 nuts and EGR pipe with cooler sub-assembly from the EGR valve assembly.


i.
A377704

Remove the EGR valve gasket from the EGR valve assembly.


j.
A379108

Using an E8 "TORX" socket wrench, remove the 3 stud bolts from the EGR pipe with cooler sub-assembly.

HINT:

If a stud bolt is deformed or the threads are damaged, replace it.