Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM32K0E _54 Brake _060044 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0294924 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1252  Brake Booster Pump Motor on Time Abnormally Long  C1253  Pump Motor Relay  


DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) detects decreases in the accumulator pressure according to the data from the accumulator pressure sensor, and then starts and stops the pump motor by operating the motor relay.

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1252 Brake Booster Pump Motor on Time Abnormally Long 311 The pump motor is operating continuously for 178 seconds or more. (When the relay is malfunctioning for 98 seconds or more.)
·

Short in pump motor circuit or pump motor monitor circuit

·

Motor relay stuck

·

Accumulator pressure sensor malfunction

·

Skid control ECU (brake booster with master cylinder assembly)


Electronically controlled brake system DTC
C1253 Pump Motor Relay 321
322
327
328
·

INF Code: 321, 327, 328

-

An open is detected in the motor relay drive circuit for 0.2 seconds or more.


·

INF Code: 322

-

A short is detected in the motor relay drive circuit for 2 seconds or more.



·

INF Code: 321, 327, 328

-

Open in pump motor circuit or pump motor monitor circuit

-

Skid control ECU (brake booster with master cylinder assembly)


·

INF Code: 322

-

Short in pump motor circuit or pump motor monitor circuit

-

Skid control ECU (brake booster with master cylinder assembly)



Electronically controlled brake system DTC

WIRING DIAGRAM

C345755E07
4.75,5.333 5.208,5.531 0.458,0.198 10 false A39 4.75,5.531 6.813,5.927 2.063,0.396 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 5.146,7.323 6.542,7.583 1.396,0.26 10 false to Auxiliary Battery 3.281,4.688 4.375,4.927 1.094,0.24 10 false ABS MTR NO. 2 3.271,3.854 4.354,4.063 1.083,0.208 10 false ABS MTR NO. 1 4.406,3.573 4.865,3.771 0.458,0.198 10 false 2 4.333,4.406 4.792,4.604 0.458,0.198 10 false 28 4.615,3.802 5.073,4 0.458,0.198 10 false MRI1 4.604,4.635 5.063,4.833 0.458,0.198 10 false MRI2 4.917,2.344 5.302,2.729 0.385,0.385 10 false Motor Relay 6.406,2.094 6.865,2.292 0.458,0.198 10 false IC 4.333,1.354 4.792,1.552 0.458,0.198 10 false 27 4.604,1.594 5.063,1.792 0.458,0.198 10 false MRO2 4.406,0.521 4.865,0.719 0.458,0.198 10 false 1 4.615,0.75 5.073,0.948 0.458,0.198 10 false MRO1 1.146,0.75 1.604,0.948 0.458,0.198 10 false BM1 1.552,0.521 2.01,0.719 0.458,0.198 10 false 2 1.135,1.604 1.594,1.802 0.458,0.198 10 false BM2 1.063,6.115 1.521,6.313 0.458,0.198 10 false GND1 1.552,5.854 2.01,6.052 0.458,0.198 10 false 4 1.052,7.063 1.51,7.26 0.458,0.198 10 false GND2 1.552,6.813 2.01,7.01 0.458,0.198 10 false 3 1.563,1.344 2.021,1.542 0.458,0.198 10 false 1 0.177,7.99 0.635,8.188 0.458,0.198 10 false A12 0.167,8.167 1.49,8.552 1.323,0.385 10 false Brake Booster Pump Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.READ VALUE USING GTS (MOTOR RELAY 1 AND MOTOR RELAY 2)
a.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ECB Motor Relay Motor relay 1 operation request ON or OFF ON: Relay on
OFF: Relay off
ECB: Electronically Controlled Brake System
ECB Motor Relay2 Motor relay 2 operation request ON or OFF ON: Relay on
OFF: Relay off
ECB: Electronically Controlled Brake System
Chassis > ABS/VSC/TRC > Data List
Tester Display
ECB Motor Relay
ECB Motor Relay2
50003 105 63,64

b.

Depress the brake pedal several times and check the operation status of the motor relay 1 and motor relay 2.

HINT:

Depressing the brake pedal several times drops the accumulator pressure and operates the pump motor.



Result:
Result Proceed to
The motor relay 1 and motor relay 2 in the Data List turns on or off by depressing the brake pedal several times. A
The status of motor relay 1 and motor relay 2 in the Data List does not change even after depressing the brake pedal several times. B



A

2.INSPECT BRAKE BOOSTER PUMP ASSEMBLY

B

7.CHECK HARNESS AND CONNECTOR (MRI TERMINAL)
2.INSPECT BRAKE BOOSTER PUMP ASSEMBLY
a.
C345125C06
0.698,1.333 1.448,1.656 true 1.99,1.604 2.74,1.302 true 2.01,2.125 2.719,2.656 true 0.729,2.625 1.427,2.135 true 0.208,0.198 0.521,0.396 0.313,0.198 10 false *a 0.385,1.229 0.698,1.427 0.313,0.198 10 false BM1 0.323,2.563 0.75,2.792 0.427,0.229 10 false GND1 2.75,2.594 3.188,2.854 0.438,0.26 10 false GND2 2.792,1.188 3.188,1.406 0.396,0.219 10 false BM2
*a Component without harness connected
(Brake Booster Pump Assembly)


Turn the power switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the A12 brake booster pump assembly connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (BM1) - 4 (GND1) Always Below 10 Ω
1 (BM2) - 3 (GND2) Always Below 10 Ω
2 (BM1) - 1 (BM2) Always Below 1 Ω
4 (GND1) - 3 (GND2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

3.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.
C345124C08
0.354,1.01 0.76,1.281 0.406,0.271 0.865,2.958 1.521,2.479 true 1.906,2.469 2.719,2.958 true 0.229,0.25 0.542,0.406 0.313,0.156 10 false *a 0.438,1.063 0.896,1.26 0.458,0.198 10 false A12 0.646,2.979 1.104,3.177 0.458,0.198 10 false GND2 2.615,2.979 3.073,3.177 0.458,0.198 10 false GND1
*a Front view of wire harness connector
(to Brake Booster Pump Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A12-4 (GND1) - Body ground Always Below 1 Ω
A12-3 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (ACCUMULATOR PRESSURE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)

4.READ VALUE USING GTS (ACCUMULATOR PRESSURE)
a.

Reconnect the A12 brake booster pump assembly connector.


b.

Disconnect the A44 brake pedal stroke sensor assembly connector.


c.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
MT Voltage Value MT voltage value Min.: 0.00 V, Max.: 20.00 V Pump motor off: 0.00 V
Pump motor on: 12.00 V
-
Accumulator Pressure Accumulator pressure output value Min.: 0.00 MPa, Max.: 24.48 MPa 15.00 to 21.00 MPa
(Pressure stable and pump motor stopped)
When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator
Chassis > ABS/VSC/TRC > Data List
Tester Display
MT Voltage Value
Accumulator Pressure
50003 105 279,502

d.

Depress the brake pedal several times to operate the pump motor, then wait until it stops.


e.

After the pump motor stops, wait for 30 seconds, then check the drop in the accumulator pressure sensor output value and the state of the pump motor.

HINT:
·

This inspection checks whether an accumulator pressure sensor malfunction, internal brake actuator (brake booster with master cylinder assembly) leak or prolonged operation due to detection of low pressure caused by accumulator deterioration, caused the DTC to be stored.

·

If the brake fluid level in the brake master cylinder reservoir assembly (brake booster with master cylinder assembly) drops, an external brake fluid leak is suspected.




Result:
Result Proceed to
The drop in the accumulator pressure sensor output value is less than 2.50 MPa 30 seconds after the pump motor stops, and the pump motor does not operate within 30 seconds after the pump motor stops. A
The drop in the accumulator pressure sensor output value is 2.50 MPa or more 30 seconds after the pump motor stops, or the pump motor operates within 30 seconds after the pump motor stops. B



A

5.RECONFIRM DTC

B

6.READ VALUE USING GTS (SERVO PRESSURE)
5.RECONFIRM DTC
a.

Turn the power switch off.


b.

Reconnect the A44 brake pedal stroke sensor assembly connector.


c.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

d.

Turn the power switch off.


e.

Turn the power switch on (IG).


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTCs C1252 and C1253 are not output. A
DTCs C1252 and/or C1253 are output. (for LHD) B
DTCs C1252 and/or C1253 are output. (for RHD) C



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

6.READ VALUE USING GTS (SERVO PRESSURE)
a.

Turn the power switch off.


b.

Reconnect the A44 brake pedal stroke sensor assembly connector.


c.

Select the Active Test on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
ECB Solenoid (SLR) Valve Close Linear solenoid reduction valve (SLR) Valve close ON/OFF ECB: Electronically Controlled Brake System
Chassis > ABS/VSC/TRC > Active Test
Tester Display
ECB Solenoid (SLR) Valve Close
50004 105 81

d.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Servo Pressure Pressure value of servo Min.: 0.00 MPa, Max.: 24.48 MPa Brake pedal released: 0.00 to 2.10 MPa Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal
Chassis > ABS/VSC/TRC > Data List
Tester Display
Servo Pressure
50003 105 501

e.

Perform the Active Test and operate the linear solenoid (SLR) in the brake actuator (brake booster with master cylinder assembly).


f.

Check that the servo pressure output value does not increase when performing the Active Test.

OK:

The servo pressure output value does not increase when performing the Active Test.


HINT:

If the servo pressure output value increases, an internal brake fluid leak in the brake actuator (brake booster with master cylinder assembly) is suspected.



Result:
Result Proceed to
The servo pressure output value increases. (for LHD) A
The servo pressure output value increases. (for RHD) B
The servo pressure output value does not increase. (for LHD) C
The servo pressure output value does not increase. (for RHD) D



A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPLACE BRAKE BOOSTER PUMP ASSEMBLY

D

REPLACE BRAKE BOOSTER PUMP ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (MRI TERMINAL)
a.
C343117C82
0.25,0.708 0.635,0.99 0.385,0.281 1.26,1.656 1.594,0.74 true 1.583,3 1.281,2.021 true 0.198,0.219 0.51,0.375 0.313,0.156 10 false *a 0.333,0.76 0.792,0.958 0.458,0.198 10 false A39 1.458,0.563 1.917,0.76 0.458,0.198 10 false MRI1 1.438,3.021 1.896,3.219 0.458,0.198 10 false MRI2
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Turn the power switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the A39 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A39-2 (MRI1) - Body ground Always 11 to 14 V
A39-28 (MRI2) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE BOOSTER PUMP ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (MRI CIRCUIT)

8.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE BOOSTER PUMP ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A12 brake booster pump assembly connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A39-1 (MRO1) - A12-2 (BM1) Always Below 1 Ω
A39-1 (MRO1) or A12-2 (BM1) - Body ground Always 10 kΩ or higher
A39-27 (MRO2) - A12-1 (BM2) Always Below 1 Ω
A39-27 (MRO2) or A12-1 (BM2) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR