Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER PUMP(for LHD) › 2016.10–2019.09
RM32K0E _54 Brake _060045 BRAKE SYSTEM (OTHER) _0299585 BRAKE BOOSTER PUMP(for LHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER PUMP(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during brake booster pump assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Simple intelligent parking assist system*1
Toyota parking assist-sensor system*1
Pre-collision system
Initialize back door lock Power door lock control system (Click here)

*1: When performing learning using the GTS.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>SIMPLE INTELLIGENT PARKING ASSIST SYSTEM>CALIBRATION

NOTICE:

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.


PROCEDURE

Hide 44551C 2.SEPARATE NO. 1 BRAKE ACTUATOR TUBE

a.
C366951

Remove the 2 nuts and separate the No. 1 brake actuator tube.


Hide 473A1 3.REMOVE ACCUMULATOR TO BRAKE MASTER CYLINDER TUBE

a.
C366952

Using a union nut wrench, disconnect the accumulator to brake master cylinder tube from the brake booster with master cylinder assembly.


b.
C372311

Disengage the 6 clamps to remove the No. 1 brake tube clamp from the accumulator to brake master cylinder tube and brake lines.

NOTICE:

Do not kink or damage the brake lines.



c.
C366953C01
0.448,0.281 0.854,0.521 true 0.25,0.177 0.563,0.333 0.313,0.156 10 false *a
*a Clamp Cover


Disengage the claw to separate the clamp cover.


d.

Disengage the 6 clamps to separate the No. 2 brake tube clamp from the accumulator to brake master cylinder tube and brake lines.

NOTICE:

Do not kink or damage the brake lines.



e.

Disenga the clamp to remove the No. 2 brake tube clamp from the vehicle body.


f.

Disengage the 6 clamps to remove the No. 1 brake tube clamp from the accumulator to brake master cylinder tube and brake lines.

NOTICE:

Do not kink or damage the brake lines.



g.

Remove the accumulator to brake master cylinder tube.


Hide 47070 4.REMOVE BRAKE BOOSTER PUMP ASSEMBLY

a.
C366954

Disengage the clamp to separate the No. 3 front brake tube from the brake actuator bracket assembly.


b.
C366955

Remove the 2 nuts.


c.

Remove the bolt of the brake actuator bracket assembly.

C366956C01
3.719,3.26 4.073,2.802 4.073,2.802 4.24,2.802 false 4.469,3.208 4.708,2.948 4.708,2.948 4.875,2.948 false 2.313,3.417 2.479,3.417 2.479,3.417 2.656,3.219 false 3.302,3.615 3.479,3.615 3.479,3.615 3.625,3.438 false 2.115,3.313 2.427,3.469 0.313,0.156 10 false *1 4.927,2.854 5.24,3.01 0.313,0.156 10 false *2 3.083,3.5 3.396,3.656 0.313,0.156 10 false *3 4.292,2.688 4.604,2.844 0.313,0.156 10 false *4
*1 Union *2 Connector
*3 Wire Harness *4 Stud
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)



d.

Remove the brake booster pump assembly as shown in the illustration.

NOTICE:
·

Do not apply excessive force to the brake lines or refrigerant lines.

·

Do not carry the brake booster pump assembly by the parts shown in the illustration.

·

Do not drop the brake booster pump assembly when carrying it.

·

Be careful not to allow brake fluid to enter the connector.



HINT:

Move the brake actuator bracket assembly as necessary to allow the brake booster pump assembly to be removed.



e.

Remove the brake actuator bracket assembly from the vehicle body.

NOTICE:

Do not apply excessive force to the brake lines or refrigerant lines.



f.
C347165

Remove the brake actuator case collar and brake booster pump bushing from the brake actuator bracket assembly.


Hide 44571A 5.REMOVE NO. 1 BRAKE ACTUATOR HOSE

a.
C347162

Slide the clip and remove the No. 1 brake actuator hose from the brake booster pump assembly.


Hide 47381 6.REMOVE NO. 1 BRAKE TUBE CLAMP BRACKET

a.
C347164

Remove the bolt and No. 1 brake tube clamp bracket from the brake booster pump assembly.