The brake pedal stroke sensor assembly sends a signal about the pedal stroke to the skid control ECU (brake booster with master cylinder assembly).
| DTC No. | Detection Item | INF Code | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|---|
| C1247 | Stroke Sensor | 211
212 213 214 215 216 217 |
·
INF Code: 211 -
The sensor supply voltage (VCSK) is 4.7 V or less, or 5.3 V or more for 0.2 seconds or more. ·
INF Code: 212 -
The sensor output voltage 1 (SKS1) is less than 0.3 V, or 4.7 V or more for 0.2 seconds or more. ·
INF Code: 213 -
The sensor output voltage 2 (SKS2) is less than 0.3 V, or 4.7 V or more for 0.2 seconds or more. ·
INF Code: 214 -
The difference between the current value and previous value of the sensor output voltage 1 (SKS1) is 8.5% or more for 0.2 seconds or more. ·
INF Code: 215 -
The difference between the current value and previous value of the sensor output voltage 2 (SKS2) is 8.5% or more for 0.2 seconds or more. ·
INF Code: 216 -
The difference in change between sensor output voltage 1 (SKS1) and sensor output voltage 2 (SKS2) is excessively large for 0.2 seconds or more. (The comparison value of SKS1 and SKS2 is invalid.) ·
INF Code: 217 -
Sensor data is invalid for 0.2 seconds or more. (The sensor data of SKS1 and SKS2 is invalid.) |
·
INF Code: 211 -
Open or short in brake pedal stroke sensor assembly power supply circuit -
Improperly connected connector, deformation or corrosion of terminals -
Skid control ECU (brake booster with master cylinder assembly) ·
INF Code: 212, 213, 214, 215, 216, 217 -
Open or short in wire harness -
Improperly connected connector, deformation or corrosion of terminals -
Brake pedal stroke sensor assembly |
Electronically controlled brake system DTC |
| C1392 | Zero Point Calibration of Stroke Sensor undone | 1124 | The brake pedal stroke sensor assembly zero point calibration is not performed.
(Normal brake pedal stroke sensor assembly zero point not memorized.) |
Normal brake pedal stroke sensor assembly zero point not memorized.
(Linear solenoid valve offset learning is not performed or Test Mode is not performed or not complete.) |
Electronically controlled brake system DTC
|
After replacing the skid control ECU (brake booster with master cylinder assembly) or brake pedal stroke sensor assembly, perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION
Check the condition of each related circuit connector before troubleshooting.
Check that the brake pedal and the brake pedal stroke sensor assembly are properly installed and that the pedal can be depressed normally.
Check and adjust the brake pedal height.
for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for LHD)>ADJUSTMENT
for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for RHD)>ADJUSTMENT
Adjust the brake pedal stroke sensor assembly.
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE PEDAL STROKE SENSOR (for LHD)>INSTALLATION
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE PEDAL STROKE SENSOR (for RHD)>INSTALLATION
| Proceed to |
|---|
| NEXT |
NEXT
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Disconnect the A39 skid control ECU (brake booster with master cylinder assembly) connector.
Disconnect the A44 brake pedal stroke sensor assembly connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A39-13 (SKG1) - A44-5 (SKG) | Always | Below 1 Ω |
| A39-13 (SKG1) or A44-5 (SKG) - Body ground | Always | 10 kΩ or higher |
| A39-17 (SKS1) - A44-6 (SKS1) | Always | Below 1 Ω |
| A39-17 (SKS1) or A44-6 (SKS1) - Body ground | Always | 10 kΩ or higher |
| A39-19 (SKS2) - A44-1 (SKS2) | Always | Below 1 Ω |
| A39-19 (SKS2) or A44-1 (SKS2) - Body ground | Always | 10 kΩ or higher |
| A39-21 (VSK2) - A44-2 (VSK2) | Always | Below 1 Ω |
| A39-21 (VSK2) or A44-2 (VSK2) - Body ground | Always | 10 kΩ or higher |
| A39-25 (VSK1) - A44-4 (VCSK) | Always | Below 1 Ω |
| A39-25 (VSK1) or A44-4 (VCSK) - Body ground | Always | 10 kΩ or higher |
| A39-33 (SKG2) - A44-3 (SKG2) | Always | Below 1 Ω |
| A39-33 (SKG2) or A44-3 (SKG2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Brake Pedal Stroke Sensor Assembly) |
Reconnect the A39 skid control ECU (brake booster with master cylinder assembly) connector.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A44-4 (VCSK) - A44-5 (SKG) | Power switch on (IG) | 4.84 to 5.16 V |
| A44-2 (VSK2) - A44-3 (SKG2) | Power switch on (IG) | 4.84 to 5.16 V |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG (for LHD) | C |
| NG (for RHD) | D |
A
B
C
D