The skid control ECU (brake booster with master cylinder assembly) stores identification information sent from other ECUs when the vehicle is shipped from the factory and changes the control constant for each system (ABS, VSC, TRC, etc.) based on the identification information.
DTC C1203 is output when an incorrect ECU is installed. If initialization is performed and learning occurs with an incorrect ECU installed, operations and functions will differ from those stored when the vehicle was shipped from the factory. Therefore, make sure that learning occurs properly.
| DTC No. | Detection Item | INF Code | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|---|
| C1203 | ECM Communication Circuit | 1161 | Either of the following is detected:
1.
Identification information sent from other ECUs does not match with the value stored when shipped from the factory. 2.
Identification information sent from other ECUs is not stored when shipped from the factory. |
·
Other ECUs are not installed correctly ·
Skid control ECU (brake booster with master cylinder assembly) |
Electronically controlled brake system DTC
|
| Vehicle Condition | |||
|---|---|---|---|
| Pattern 1 | Pattern 2 | ||
| Diagnosis Condition | - | - | - |
| Malfunction Status | Identification information sent from other ECUs does not match with the value stored when shipped from the factory. | ○ | - |
| Identification information sent from other ECUs is not stored when shipped from the factory. | - | ○ | |
| Detection Time | - | - | |
| Number of Trips | 1 trip | 1 trip | |
DTC will be output when conditions for either of the patterns in the table above are met.
After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION
Check that the proper hybrid vehicle control ECU and main body ECU (multiplex network body ECU) are installed.
Proper ECUs are installed.
Check if the hybrid vehicle control ECU and main body ECU (multiplex network body ECU) were replaced before the DTC was recorded.
ECUs were not replaced.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (A proper hybrid vehicle control ECU is not installed and/or the hybrid vehicle control ECU was replaced.) | B |
| NG (A proper main body ECU (multiplex network body ECU) is not installed and/or the main body ECU (multiplex network body ECU) was replaced.) | C |
A
B
C
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Perform linear solenoid valve offset learning, ABS holding solenoid valve learning and system information memorization.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION
| Tester Display |
|---|
| ECB Utility |
Perform yaw rate and acceleration sensor zero point calibration.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>CALIBRATION
| Tester Display |
|---|
| Test Mode |
After installing a new skid control ECU (brake booster with master cylinder assembly), before performing linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization, DTC C1203 will be output.
If linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization are not performed, DTC C1203 will be output after the data stored in the skid control ECU (brake booster with master cylinder assembly) is cleared by performing "Reset Memory" using GTS.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Turn the power switch off.
Turn the power switch on (IG).
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| DTC C1203 is output. (for LHD) | A |
| DTC C1203 is output. (for RHD) | B |
| DTC C1203 is not output. | C |
A
B
C