Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2016.10–2019.09
RM32K0E _54 Brake _060044 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0294924 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1381  Abnormal Power Supply Voltage in Yaw Rate and/or Deceleration Sensor  


DESCRIPTION

The airbag sensor assembly has a built-in yaw rate and acceleration sensor and detects the vehicle condition using 2 circuits (GL1, GL2).

If a power source malfunction signal from the yaw rate and acceleration sensor (airbag sensor assembly) is detected by the skid control ECU (brake booster with master cylinder assembly), DTC C1381 is stored.

DTC C1381 may be stored due to an intermittent low power source voltage.

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1381 Abnormal Power Supply Voltage in Yaw Rate and/or Deceleration Sensor 601 At a vehicle speed of more than 3 km/h (2 mph), the acceleration sensor power source malfunction signal is received for 10 seconds or more.
·

Wire harness or connector

·

Acceleration sensor (airbag sensor assembly)


ABS DTC

WIRING DIAGRAM

C270520E81
0.813,1.313 1.427,1.51 0.615,0.198 10 false CANL 6.063,1.333 6.677,1.531 0.615,0.198 10 false CA1L 0.792,0.719 1.406,0.917 0.615,0.198 10 false CANH 6.052,0.719 6.667,0.917 0.615,0.198 10 false CA1H 0.948,1.948 1.406,2.146 0.458,0.198 10 false IG2 2.125,2.104 3.063,2.396 0.938,0.292 10 false A/BAG-IG2 3.917,1.927 5.365,2.344 1.448,0.417 10 false from IG2-NO. 2 Relay 1,2.563 1.313,2.76 0.313,0.198 10 false E1 1,3.177 1.313,3.375 0.313,0.198 10 false E2 0.063,4.167 2.229,4.552 2.167,0.385 10 false Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly) 0.073,3.99 0.531,4.188 0.458,0.198 10 false F70 3.49,3.156 5.573,3.635 2.083,0.479 10 false : CAN Communication Line 5.073,4.083 7.125,4.51 2.052,0.427 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 5.083,3.917 5.542,4.115 0.458,0.198 10 false A39 5.781,1.156 6.094,1.354 0.313,0.198 10 false 42 5.781,0.531 6.094,0.729 0.313,0.198 10 false 43 1.271,0.531 1.583,0.729 0.313,0.198 10 false 13 1.281,1.156 1.594,1.354 0.313,0.198 10 false 22 1.281,1.833 1.594,2.031 0.313,0.198 10 false 21 1.292,2.448 1.604,2.646 0.313,0.198 10 false 25 1.281,3.052 1.594,3.25 0.313,0.198 10 false 26

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing or reinstalling the yaw rate and acceleration sensor (airbag sensor assembly), perform yaw rate and acceleration sensor zero point calibration after clearing previously calibrated data.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (IG2 TERMINAL)
a.
C234074C31
0.354,0.948 0.677,1.188 0.323,0.24 0.802,1.875 1.063,1.469 true 0.396,0.979 0.854,1.177 0.458,0.198 10 false F70 0.208,0.229 0.521,0.427 0.313,0.198 10 false *a 0.677,1.865 1.135,2.063 0.458,0.198 10 false IG2
*a Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the F70 yaw rate and acceleration sensor (airbag sensor assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Turn the power switch on (IG).


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F70-21 (IG2) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG2 CIRCUIT)

2.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.
C234074C32
0.354,0.948 0.677,1.188 0.323,0.24 1.5,1.875 1.688,1.479 true 2.125,1.865 1.854,1.469 true 0.396,0.979 0.854,1.177 0.458,0.198 10 false F70 0.208,0.229 0.521,0.427 0.313,0.198 10 false *a 1.427,1.875 1.74,2.073 0.313,0.198 10 false E1 2.104,1.875 2.417,2.073 0.313,0.198 10 false E2
*a Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly))


Turn the power switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F70-25 (E1) - Body ground Always Below 1 Ω
F70-26 (E2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)

3.RECONFIRM DTC
a.

Reconnect the F70 yaw rate and acceleration sensor (airbag sensor assembly) connector.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the power switch off.


d.

Turn the power switch on (READY).


e.

Perform a road test.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1381 is not output. A
DTC C1381 is output. B



A

B