Refer to DTCs C1413 and C1414.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C1413
| DTC No. | Detection Item | INF Code | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|---|
| C1405 | Open or Short in Front Speed Sensor RH Circuit | 503
506 508 |
·
INF Code: 503 -
An open in the speed sensor signal circuit continues for 0.5 seconds or more. ·
INF Code: 506 -
The speed sensor power source voltage is low for 0.5 seconds or more. ·
INF Code: 508 -
The speed sensor power source voltage is low for 0.2 seconds, and does not return to normal for 60 seconds or more. |
·
Front speed sensor RH ·
Wire harness or connector ·
Skid control ECU (brake booster with master cylinder assembly) |
ABS DTC |
| C1406 | Open or Short in Front Speed Sensor LH Circuit | 513
516 518 |
·
INF Code: 513 -
An open in the speed sensor signal circuit continues for 0.5 seconds or more. ·
INF Code: 516 -
The speed sensor power source voltage is low for 0.5 seconds or more. ·
INF Code: 518 -
The speed sensor power source voltage is low for 0.2 seconds, and does not return to normal for 60 seconds or more. |
·
Front speed sensor LH ·
Wire harness or connector ·
Skid control ECU (brake booster with master cylinder assembly) |
ABS DTC |
Refer to DTCs C1413 and C1414.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C1413
After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION
Using the GTS, check for any momentary interruptions in the wire harness and connector corresponding to a DTC.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Speed Open | Front speed sensor RH open detection | Error or Normal | Error: Momentary interruption
Normal: Normal |
- |
| FL Speed Open | Front speed sensor LH open detection | Error or Normal | Error: Momentary interruption
Normal: Normal |
- |
| Tester Display |
|---|
| FR Speed Open |
| FL Speed Open |
Check for any momentary interruptions in the wire harness and connectors.
There are no momentary interruptions.
Perform the above inspection before removing the sensor and connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Select the Data List on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Wheel Speed | Front speed sensor RH | Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| FL Wheel Speed | Front speed sensor LH | Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Tester Display |
|---|
| FR Wheel Speed |
| FL Wheel Speed |
Check the speed sensor output value.
The output value changes in accordance with the vehicle speed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Turn the power switch off.
Turn the power switch on (READY).
Perform a road test.
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| DTCs C1405 and C1406 are not output. | A |
| DTCs C1405 and/or C1406 are output. (for LHD) | B |
| DTCs C1405 and/or C1406 are output. (for RHD) | C |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
Turn the power switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Disconnect the A39 skid control ECU (brake booster with master cylinder assembly) connector.
Disconnect the A25 or A13 front speed sensor connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A39-3 (FR+) - A25-1 (FR+) | Always | Below 1 Ω |
| A39-3 (FR+) or A25-1 (FR+) - Body ground | Always | 10 kΩ or higher |
| A39-4 (FR-) - A25-2 (FR-) | Always | Below 1 Ω |
| A39-4 (FR-) or A25-2 (FR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A39-31 (FL+) - A13-1 (FL+) | Always | Below 1 Ω |
| A39-31 (FL+) or A13-1 (FL+) - Body ground | Always | 10 kΩ or higher |
| A39-32 (FL-) - A13-2 (FL-) | Always | Below 1 Ω |
| A39-32 (FL-) or A13-2 (FL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | for RH |
| *B | for LH |
| *a | Front view of wire harness connector
(to Front Speed Sensor) |
Reconnect the A39 skid control ECU (brake booster with master cylinder assembly) connector.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A25-1 (FR+) - Body ground | Power switch on (IG) | 8 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A13-1 (FL+) - Body ground | Power switch on (IG) | 8 to 14 V |
Check the speed sensor signal after replacement.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C