Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM32K0E _54 Brake _060044 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0294924 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1407  Open or Short in Rear Speed Sensor RH Circuit  C1408  Open or Short in Rear Speed Sensor LH Circuit  


DESCRIPTION

Refer to DTCs C1415 and C1416.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C1415

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1407 Open or Short in Rear Speed Sensor RH Circuit 523
526
528
·

INF Code: 523

-

An open in the speed sensor signal circuit continues for 0.5 seconds or more.


·

INF Code: 526

-

The speed sensor power source voltage is low for 0.5 seconds or more.


·

INF Code: 528

-

The speed sensor power source voltage is low for 0.2 seconds, and does not return to normal for 60 seconds or more.



·

Skid control sensor wire RH (No. 1 parking Brake wire assembly)

·

Rear speed sensor RH (rear axle hub and bearing assembly RH)

·

Wire harness or connector

·

Skid control ECU (brake booster with master cylinder assembly)


ABS DTC
C1408 Open or Short in Rear Speed Sensor LH Circuit 533
536
538
·

INF Code: 533

-

An open in the speed sensor signal circuit continues for 0.5 seconds or more.


·

INF Code: 536

-

The speed sensor power source voltage is low for 0.5 seconds or more.


·

INF Code: 538

-

The speed sensor power source voltage is low for 0.2 seconds, and does not return to normal for 60 seconds or more.



·

Skid control sensor wire RH (No. 2 parking Brake wire assembly)

·

Rear speed sensor LH (rear axle hub and bearing assembly LH)

·

Wire harness or connector

·

Skid control ECU (brake booster with master cylinder assembly)


ABS DTC

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION

·

Disassembly of the rear speed sensor from the rear axle hub and bearing assembly is prohibited.



PROCEDURE

1.READ VALUE USING GTS (MOMENTARY INTERRUPTION)
a.

Using the GTS, check for any momentary interruptions in the wire harness and connector corresponding to a DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>CHECK FOR INTERMITTENT PROBLEMS

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Speed Open Rear speed sensor RH open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
RL Speed Open Rear speed sensor LH open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Speed Open
RL Speed Open
50003 105 202,203

b.

Check for any momentary interruptions in the wire harness and connectors.


OK:

There are no momentary interruptions.


NOTICE:

Perform the above inspection before removing the sensor and connector.


Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (REAR SPEED SENSOR)

NG

4.INSPECT SKID CONTROL SENSOR WIRE (PARKING BRAKE WIRE ASSEMBLY)
2.READ VALUE USING GTS (REAR SPEED SENSOR)
a.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Wheel Speed Rear speed sensor RH Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear speed sensor LH Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Wheel Speed
RL Wheel Speed
50003 105 3,4

b.

Check the speed sensor output value.

OK:

The output value changes in accordance with the vehicle speed.



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

4.INSPECT SKID CONTROL SENSOR WIRE (PARKING BRAKE WIRE ASSEMBLY)
3.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the power switch off.


c.

Turn the power switch on (READY).


d.

Perform a road test.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTCs C1407 and C1408 are not output. A
DTCs C1407 and/or C1408 are output. (for LHD) B
DTCs C1407 and/or C1408 are output. (for RHD) C



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

4.INSPECT SKID CONTROL SENSOR WIRE (PARKING BRAKE WIRE ASSEMBLY)
a.
C367773C02
0.833,0.417 1.333,0.667 0.5,0.25 0.833,0.75 1.333,1 0.5,0.25 2.25,0.417 2.75,0.667 0.5,0.25 2.25,0.75 2.75,1 0.5,0.25 0.927,1.781 0.583,2.5 true 0.927,1.781 0.583,2.5 true 1.156,1.781 1.438,2.51 true 2.344,1.948 2.125,2.365 true 2.615,1.938 2.865,2.344 true 1.365,0.448 1.677,0.604 0.313,0.156 10 false *d 1.365,0.781 1.677,0.938 0.313,0.156 10 false *e 0.25,0.208 0.563,0.365 0.313,0.156 10 false *a 0.99,1.052 1.302,1.208 0.313,0.156 10 false *b 2.406,1.083 2.719,1.24 0.313,0.156 10 false *c 2.771,0.427 3.083,0.583 0.313,0.156 10 false *d 2.771,0.781 3.083,0.938 0.313,0.156 10 false *e 0.375,2.542 0.969,2.719 0.594,0.177 10 false -*d 1.406,2.552 2,2.729 0.594,0.177 10 false +*d 1.896,2.396 2.49,2.573 0.594,0.177 10 false RR+*d 2.708,2.375 3.302,2.552 0.594,0.177 10 false RR-*d 0.375,2.729 0.854,2.875 0.479,0.146 10 false -*e 1.406,2.719 1.885,2.865 0.479,0.146 10 false +*e 2.729,2.552 3.208,2.698 0.479,0.146 10 false RL-*e 1.906,2.573 2.385,2.719 0.479,0.146 10 false RL+*e 0.99,0.448 1.302,0.604 0.313,0.156 10 false d1 1,0.781 1.313,0.938 0.313,0.156 10 false e1 2.354,0.438 2.667,0.594 0.313,0.156 10 false dM1 2.365,0.792 2.677,0.948 0.313,0.156 10 false eM1
*a Front view of skid control sensor wire
(parking brake wire assembly)
*b Front view of wire harness connector
(to Sensor Side Connector)
*c Front view of wire harness connector
(to Vehicle Side Connector)
*d for RH
*e for LH


Turn the power switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Remove the skid control sensor wire RH (No. 1 parking Brake wire assembly) or the skid control sensor wire RH (No. 2 parking Brake wire assembly).


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
d1-2 (+) - dM1-1 (RR+) Always Below 1 Ω
d1-2 (+) - dM1-2 (RR-) Always 10 kΩ or higher
d1-2 (+) or dM1-1 (RR+) - Body ground Always 10 kΩ or higher
d1-1 (-) - dM1-2 (RR-) Always Below 1 Ω
d1-1 (-) - dM1-1 (RR+) Always 10 kΩ or higher
d1-1 (-) or dM1-2 (RR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
e1-2 (+) - eM1-1 (RL+) Always Below 1 Ω
e1-2 (+) - eM1-2 (RL-) Always 10 kΩ or higher
e1-2 (+) or eM1-1 (RL+) - Body ground Always 10 kΩ or higher
e1-1 (-) - eM1-2 (RL-) Always Below 1 Ω
e1-1 (-) - eM1-1 (RL+) Always 10 kΩ or higher
e1-1 (-) or eM1-2 (RL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - SKID CONTROL SENSOR WIRE (PARKING BRAKE WIRE ASSEMBLY))

NG

REPLACE SKID CONTROL SENSOR WIRE (PARKING BRAKE WIRE ASSEMBLY)

5.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - SKID CONTROL SENSOR WIRE (PARKING BRAKE WIRE ASSEMBLY))
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A39 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A39-7 (RR+) - dM1-1 (RR+) Always Below 1 Ω
A39-7 (RR+) or dM1-1 (RR+) - Body ground Always 10 kΩ or higher
A39-8 (RR-) - dM1-2 (RR-) Always Below 1 Ω
A39-8 (RR-) or dM1-2 (RR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A39-34 (RL+) - eM1-1 (RL+) Always Below 1 Ω
A39-34 (RL+) or eM1-1 (RL+) - Body ground Always 10 kΩ or higher
A39-35 (RL-) - eM1-2 (RL-) Always Below 1 Ω
A39-35 (RL-) or eM1-2 (RL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)
a.
C367774C01
0.833,1.167 1.333,1.417 0.5,0.25 2.333,1.167 2.833,1.417 0.5,0.25 1.146,2.292 1.5,2.917 true 2.646,2.292 3,2.917 true 1.375,1.219 1.688,1.375 0.313,0.156 10 false *A 2.854,1.208 3.167,1.365 0.313,0.156 10 false *B 0.104,0.167 0.417,0.323 0.313,0.156 10 false *a 0.958,1.198 1.365,1.375 0.406,0.177 10 false dM1 2.458,1.198 2.865,1.375 0.406,0.177 10 false eM1 1.417,2.938 1.823,3.115 0.406,0.177 10 false RR+ 2.906,2.938 3.313,3.115 0.406,0.177 10 false RL+
*A for RH
*B for LH
*a Front view of wire harness connector
(to Skid Control Sensor Wire (Parking Brake Wire Assembly))


Reconnect the A39 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Condition Specified Condition
dM1-1 (RR+) - Body ground Power switch on (IG) 8 to 14 V

for LH
Tester Connection Condition Specified Condition
eM1-1 (RL+) - Body ground Power switch on (IG) 8 to 14 V


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE


HINT:

The rear speed sensor and rear speed sensor rotor are incorporated into the rear axle hub and bearing assembly.

If the rear speed sensor and rear speed sensor rotor need to be replaced, replace the rear axle hub and bearing assembly.



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY