Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2016.10–2018.05
RM32K0E _54 Brake _060044 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0294924 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C146C  Open Circuit in ABS Motor Relay Circuit  C146D  Short Circuit in ABS Motor Relay Circuit  


DESCRIPTION

The ABS motor relay is built into the brake booster with master cylinder assembly.

During ABS, TRC, VSC or brake assist operation, the skid control ECU (brake booster with master cylinder assembly) turns on the ABS motor relay to run the pump motor in the brake actuator assembly.

When any DTC related to the ABS motor is stored, the IC built into the skid control ECU (brake booster with master cylinder assembly) operates in fail-safe mode.

When the supplied voltage to the BM terminal of the ABS motor relay is excessively low due to an auxiliary battery or charging circuit malfunction, DTC C146C and/or C146D is stored.

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C146C Open Circuit in ABS Motor Relay Circuit 612 When operation of the ABS motor is requested, the ABS motor voltage is less than 7.6 V for 0.2 seconds or more.
·

Wire harness or connector

·

Skid control ECU (brake booster with master cylinder assembly)

·

Brake actuator assembly


ABS DTC
C146D Short Circuit in ABS Motor Relay Circuit 613 A short in the ABS motor relay drive circuit is detected for 4 seconds or more.
·

Wire harness or connector

·

Skid control ECU (brake booster with master cylinder assembly)

·

Brake actuator assembly


ABS DTC

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:

When DTCs C1241 and/or C1417 are output together with C146C and/or C146D, inspect and repair the trouble areas indicated by C1241 and/or C1417 first.

for C1241: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C1241

for C1417: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C1417


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BM TERMINAL)
a.
C343117C87
0.323,0.698 0.688,0.948 0.365,0.25 0.948,2.865 1.219,2.271 true 0.385,0.75 0.698,0.948 0.313,0.198 10 false A39 0.177,0.167 0.49,0.365 0.313,0.198 10 false *a 0.844,2.865 1.156,3.063 0.313,0.198 10 false BM
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A39 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A39-41 (BM) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BM CIRCUIT)

2.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A40 brake actuator assembly connector (for LHD).


c.

Disconnect the A41 brake actuator assembly connector (for RHD).


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A39-40 (+BM) - A40-13 (+BM) Always Below 1 Ω
A39-40 (+BM) or A40-13 (+BM) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
A39-40 (+BM) - A41-13 (+BM) Always Below 1 Ω
A39-40 (+BM) or A41-13 (+BM) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.
C346353C17
0.198,0.885 0.563,1.156 0.365,0.271 0.198,0.542 0.563,0.813 0.365,0.271 0.833,1.771 1.021,2.74 true 0.198,0.083 0.51,0.281 0.313,0.198 10 false *a 0.26,0.938 0.573,1.135 0.313,0.198 10 false A41 0.823,2.76 1.417,3 0.594,0.24 10 false MGND 0.25,0.583 0.563,0.781 0.313,0.198 10 false A40 0.625,0.583 0.938,0.781 0.313,0.198 10 false *A 0.625,0.927 0.938,1.125 0.313,0.198 10 false *B
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Brake Actuator Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A40-1 (MGND) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
A41-1 (MGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)

4.RECONFIRM DTC
a.

Reconnect the A39 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Reconnect the A40 brake actuator assembly connector (for LHD).


c.

Reconnect the A41 brake actuator assembly connector (for RHD).


d.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

e.

Turn the power switch off.


f.

Turn the power switch on (READY).


g.

Perform a road test.


h.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTCs C146C and C146D are not output. A
DTCs C146C and/or C146D are output. (for LHD) B
DTCs C146C and/or C146D are output. (for RHD) C


HINT:
·

If a speed signal of 20 km/h (12 mph) or more is sent to the skid control ECU (brake booster with master cylinder assembly) with the power switch on (IG) and the stop light switch assembly off, the ECU performs self diagnosis of the motor and solenoid circuits.

·

If the normal system code is output (no DTCs are output), slightly jiggle the connectors, wire harness, and fuses of the skid control ECU (brake booster with master cylinder assembly).

·

If any DTCs are output while jiggling a connector or wire harness from the skid control ECU (brake booster with master cylinder assembly), inspect and repair the connector or wire harness.

·

The DTCs were probably output due to a bad connection of the connector terminal.





A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY