Home › Engine / Hybrid System › 2ZR-FXE (ENGINE CONTROL) › SFI SYSTEM › 2016.10–2019.09
RM32K0E _51 Engine / Hybrid System _060312 2ZR-FXE ENGINE CONTROL _0295698 SFI SYSTEM L

2ZR-FXE ENGINE CONTROL  SFI SYSTEM  PRECAUTION  


WHEN USING GTS


CAUTION:
·

Strictly obey all traffic rules and regulations.

·

Do not drive the vehicle with the GTS cable contacting the pedals, shift lever or steering wheel.

·
A356952

Driving the wheel with the GTS cable contacting these areas could impede vehicle control, resulting in a serious accident.

·
A356953

Do not operate the GTS while driving the vehicle.

·

Operating the GTS while driving the vehicle will prevent you from paying sufficient attention to vehicle surroundings, and could result in a serious accident.




INITIALIZATION


NOTICE:
·

Perform Registration (VIN registration or frame number registration) when replacing the ECM.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>REGISTRATION

·

Perform Learning Value Reset and Idle Learning after replacing or servicing parts related to engine operation.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION

·

Perform "Grill Shutter Control Mode Switching and Grill Shutter Initialization" after replacing the swing grille actuator assembly or radiator shutter sub-assembly.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>GRILLE SHUTTER SYSTEM>INITIALIZATION

·

When the cable is disconnected from the negative (-) auxiliary battery terminal, initialize the following system(s) after the cable is reconnected.

System Name See Procedure
Lane Departure Alert System (w/ Steering Control) (Click here)
Simple Intelligent Parking Assist System
Toyota parking assist-sensor system
Pre-collision system
Power Door Lock Control System




PRECAUTIONS FOR INSPECTING HYBRID CONTROL SYSTEM


a.

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After removing the service plug grip, turning the power switch on (READY) may cause a malfunction. Do not turn the power switch on (READY) unless instructed by the repair manual.




b.

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals.

A371656E01
1.74,1.469 1.896,1.667 0.156,0.198 10 true 1 2.469,1.25 2.625,1.448 0.156,0.198 10 true 2 5.604,1.094 5.76,1.292 0.156,0.198 10 true 3

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE FOR HYBRID CONTROL SYSTEM ACTIVATION


a.

When the warning light is illuminated, or the auxiliary battery has been disconnected and reconnected, attempting to turn the power switch on (READY) may not start the system (the system may not enter the READY-on state) on the first attempt. If so, turn the power switch off and reattempt to start the hybrid system.

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION




PRECAUTION WHEN REPLACING COMBINATION METER ASSEMBLY


When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.