Home › Engine / Hybrid System › 2ZR-FXE (ENGINE CONTROL) › SFI SYSTEM › 2016.10–2019.09
RM32K0E _51 Engine / Hybrid System _060312 2ZR-FXE ENGINE CONTROL _0295698 SFI SYSTEM C

2ZR-FXE ENGINE CONTROL  SFI SYSTEM  P065714  Actuator Supply Voltage "A" Circuit Short to Ground or Open  


DESCRIPTION

The electronic throttle control system has a dedicated power supply circuit. The voltage (+BM) is monitored and when it is low (less than 4 V), the ECM determines that there is a malfunction in the electronic throttle control system and cuts off the current to the throttle actuator.

When the voltage becomes unstable, the electronic throttle control system itself becomes unstable. For this reason, when the voltage is low, the current to the throttle actuator is cut. If repairs are made and the system returns to normal, turn the power switch off. The ECM then allows the current to flow to the throttle actuator so that it can be restarted.

A361818E05
0.406,1.042 1.76,1.271 1.354,0.229 10 false from EFI-MAIN Relay 0.365,1.813 1.729,2.01 1.365,0.198 10 false from Auxiliary Battery 2.49,1.99 3.083,2.188 0.594,0.198 10 false ETCS 0.823,3.552 1.99,3.833 1.167,0.281 10 false Throttle Actuator 4.698,0.979 5.292,1.177 0.594,0.198 10 false +B, +B2 4.75,1.74 5.344,1.938 0.594,0.198 10 false +BM 4.76,2.448 5.354,2.646 0.594,0.198 10 false M+ 4.76,3.083 5.354,3.281 0.594,0.198 10 false M- 4.75,3.615 5.344,3.813 0.594,0.198 10 false ME01 5.906,0.99 6.833,1.49 0.927,0.5 10 false Power Source Circuit for CPU 5.99,2.5 6.583,3.25 0.594,0.75 10 false Throttle Actuator Control Circuit 5.75,4.24 6.344,4.438 0.594,0.198 10 false ECM

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P065714 Actuator Supply Voltage "A" Circuit Short to Ground or Open An open or short is detected in the electronic throttle control system power source (+BM) circuit (1 trip detection logic).
·

Open or short in electronic throttle control system power source circuit

·

ECM


Comes on DTC stored SAE Code: P0658

MONITOR DESCRIPTION

The ECM monitors the auxiliary battery supply voltage applied to the throttle actuator.

When the power supply voltage (+BM) is less than 4 V for 0.8 seconds or more, the ECM interprets this as an open or ground short in the power supply circuit, then illuminates the MIL and stores this DTC.

MONITOR STRATEGY

Required Sensors/Components Throttle actuator
Throttle valve (throttle body assembly)
ETCS fuse
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

A199315E35
0.979,0.552 1.823,0.906 0.844,0.354 10 2500 rpm 1.24,1.927 1.719,2.219 0.479,0.292 10 Idling 0.25,2.208 1.708,2.51 1.458,0.302 10 Power Switch on (IG) 3.146,2.208 4.875,2.51 1.729,0.302 10 Approximately 5 seconds 3.469,2.802 4.896,3.156 1.427,0.354 10 16 seconds or more 2.021,2.365 2.302,2.625 0.281,0.26 10 [A] 6.01,3.229 6.292,3.479 0.281,0.25 10 [C] 4.604,0.417 4.99,0.698 0.385,0.281 10 [B]

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG) [A].

7.

Turn the GTS on.

8.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

9.

Start the engine.

10.

Slowly depress the accelerator pedal, raise the engine speed to approximately 2500 rpm over approximately 5 seconds, and then idle the engine [B].

HINT:

During charge control, the engine speed is set at idle. Therefore, the engine speed will not increase when the accelerator pedal is depressed. In this case, perform step [B] after charge control has completed.


11.

Check that 16 seconds or more have elapsed since the engine was started.

12.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

13.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



14.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

15.

Input the DTC: P065714.

16.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.

·

If the judgment result is INCOMPLETE or N/A, perform steps [B] and [C] again.




FAIL-SAFE

When this DTC is stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 5.5° throttle valve opening angle by the return spring. The ECM then adjusts the engine output, by controlling the fuel injection (intermittent fuel cut) and ignition timing, in accordance with the engine torque request signal sent from the hybrid vehicle control ECU, to allow the vehicle to continue being driven at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

Fail-safe mode continues until a pass condition is detected, and the power switch is then turned off.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Vehicle Control History may be stored in the hybrid vehicle control ECU if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY



HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (+BM VOLTAGE)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / +BM Voltage.

Powertrain > Engine > Data List
Tester Display
+BM Voltage
50003 372 82

e.

Read the Data List according to the display on the GTS.

Standard Voltage:

11 to 16 V



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - ECM, BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - ECM, BODY GROUND)
A376496C03
1.458,0.635 1.823,0.906 0.365,0.271 2.073,2.448 2.625,1.583 true 2.49,2.531 2.719,1.656 true 3.115,2.594 2.729,1.583 true 0.083,0.083 0.396,0.281 0.313,0.198 10 false *a 1.521,0.698 1.979,0.896 0.458,0.198 10 false C63 1.896,2.479 2.333,2.708 0.438,0.229 10 false ME01 2.427,2.573 2.74,2.771 0.313,0.198 10 false E1 3,2.635 3.385,2.854 0.385,0.219 10 false +BM
*a Front view of wire harness connector
(to ECM)


a.

Disconnect the ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C63-29 (+BM) - Body ground Power switch off 11 to 16 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C63-28 (ME01) - Body ground Always Below 1 Ω
C63-59 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR