Home › Engine / Hybrid System › 2ZR-FXE (ENGINE CONTROL) › ECM › 2016.10–2019.09
RM32K0E _51 Engine / Hybrid System _060312 2ZR-FXE ENGINE CONTROL _0295702 ECM A

2ZR-FXE ENGINE CONTROL  ECM  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during ECM removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Simple intelligent parking assist system*1
Toyota parking assist-sensor system*1
Pre-collision system
Initialize back door lock Power door lock control system (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on (Click here)

PROCEDURE

Hide 1. PRECAUTION

NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

If the ECM has been struck or dropped, replace it.

·

Perform the Vehicle Identification Number (VIN) registration when replacing the ECM.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>REGISTRATION



Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>2ZR-FXE AUXILIARY BATTERY>REMOVAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 89661 3.REMOVE ECM

a.
A375009C01
0.708,0.833 0.865,1.167 0.865,1.167 1.042,1.167 true 2.417,0.885 2.594,1.219 2.594,1.219 2.771,1.219 true 0.344,1.094 0.521,1.26 0.177,0.167 10 true *a 1.979,1.083 2.156,1.25 0.177,0.167 10 true *a 1.031,1.083 1.208,1.25 0.177,0.167 10 true *b 2.76,1.125 2.938,1.292 0.177,0.167 10 true *b
*a Push
*b Lock


Raise the 2 levers while pushing the locks on the levers, and disconnect the 2 ECM connectors.

NOTICE:

After disconnecting the ECM connectors, make sure that dirt, water or other foreign matter does not contact the connecting parts of the ECM connectors.



b.
A394191

Disengage the 2 clamps.


c.

Remove the bolt and separate the engine wire from the No. 1 ECM bracket.


d.
A394192C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the bolt, nut and ECM.

NOTICE:

If the ECM has been struck or dropped, replace it.



Hide 89667E 4.REMOVE NO. 1 ECM BRACKET

a.
A394193

Remove the 2 screws and No. 1 ECM bracket from the ECM.


Hide 89668 5.REMOVE NO. 2 ECM BRACKET

a.
A394194

Remove the 2 screws and No. 2 ECM bracket from the ECM.