Home › Engine / Hybrid System › 2ZR-FXE (ENGINE CONTROL) › SFI SYSTEM
RM32K0E _51 Engine / Hybrid System _060312 2ZR-FXE ENGINE CONTROL _0295698 SFI SYSTEM C

2ZR-FXE ENGINE CONTROL  SFI SYSTEM  P261029  ECM/PCM Engine Off Timer Performance Signal Invalid  


DESCRIPTION

The soak timer operates after the power switch is turned off. When a certain amount of time has elapsed since the power switch was turned off, the soak timer activates the ECM to perform malfunction checks which can only be performed after the power switch is turned off. The soak timer is built into the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P261029 ECM/PCM Engine Off Timer Performance Signal Invalid ECM internal malfunction
(2 trip detection logic)
ECM Comes on DTC stored SAE Code: P2610

A304676E23
2.781,3.813 3.427,3.979 0.646,0.167 10 false EFI-MAIN 1.948,3.219 2.594,3.385 0.646,0.167 10 false EFI-MAIN 4.313,3.365 4.813,3.531 0.5,0.167 10 false MREL 4.177,2.563 4.781,2.792 0.604,0.229 10 false +B, +B2 4.333,0.771 4.833,0.938 0.5,0.167 10 false IGSW 3.594,1.01 4.906,1.396 1.313,0.385 10 false ECU-IG2 NO. 1 1.917,1.01 2.667,1.177 0.75,0.167 10 false IG2-MAIN 2.719,1.604 3.854,1.896 1.135,0.292 10 false IG2 NO. 1 0.167,1.917 2,2.5 1.833,0.583 10 false from Auxiliary Battery 0.688,1.031 1.813,1.344 1.125,0.313 10 false BATT-MAIN 5.719,4.104 6.135,4.271 0.417,0.167 10 false ECM 5.01,3.24 5.729,3.573 0.719,0.333 10 false Main Relay Control IC 5.031,2.438 5.698,2.771 0.667,0.333 10 false Power Source IC 5.01,1.104 5.74,1.438 0.729,0.333 10 false Soak Timer IC 2.844,2 4.667,2.333 1.823,0.333 10 false from Certification ECU (Smart Key ECU Assembly)

MONITOR STRATEGY

Required Sensors/Components ECM
Frequency of Operation Once per driving cycle

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG).

7.

Turn the GTS on.

8.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

9.

Start the engine and warm it up.

10.

Turn the power switch off and wait for at least 30 seconds.

11.

Turn the power switch on (IG).

12.

Turn the GTS on.

13.

Enter the following menus: Powertrain / Engine / Trouble Codes.

14.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



15.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

16.

Input the DTC: P261029.

17.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.




CAUTION / NOTICE / HINT

HINT:
·

DTC P261029 is stored if an internal ECM problem is detected. In this case, diagnostic not required. ECM replacement is required.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

2.CLEAR DTC
2.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the power switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P261029)
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P261029)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.

Powertrain > Engine > Trouble Codes
50001 372

c.

If no pending DTC is output, the repair has been successfully completed.


Result:
Proceed to
NEXT



NEXT

END