Home › Engine / Hybrid System › 2ZR-FXE (ENGINE CONTROL) › SFI SYSTEM › 2016.10–2019.09
RM32K0E _51 Engine / Hybrid System _060312 2ZR-FXE ENGINE CONTROL _0295698 SFI SYSTEM J

2ZR-FXE ENGINE CONTROL  SFI SYSTEM  ECM Power Source Circuit  


DESCRIPTION

When the power switch is turned on (IG), auxiliary battery voltage is applied to the IGSW terminal of the ECM. The output signal from the MREL terminal of the ECM causes current to flow to the coil of the No. 1 integration relay (EFI-MAIN relay), closing the contacts of the EFI-MAIN relay and supplying power to terminals +B and +B2 of the ECM.

WIRING DIAGRAM

A376203E07
1.792,0.854 3.583,1.5 1.792,0.646 10 false Certification ECU (Smart Key ECU Assembly) 1.792,0.708 2.073,0.969 0.281,0.26 10 false F1 3.01,0.375 3.427,0.635 0.417,0.26 10 false IG1D 3.417,0.375 3.74,0.552 0.323,0.177 10 false 17 5.917,1.802 6.24,1.979 0.323,0.177 10 false 6 3.771,1.688 4.094,1.865 0.323,0.177 10 false 7 3.969,1.688 4.292,1.865 0.323,0.177 10 false 1A 4.354,1.99 4.677,2.167 0.323,0.177 10 false 1A 5.823,1.99 6.146,2.167 0.323,0.177 10 false A38 5.823,2.854 6.146,3.031 0.323,0.177 10 false A38 5.823,3.24 6.146,3.417 0.323,0.177 10 false A38 5.823,4.135 6.146,4.313 0.323,0.177 10 false A38 5.823,4.656 6.146,4.833 0.323,0.177 10 false C63 5.917,2.656 6.24,2.833 0.323,0.177 10 false 2 5.917,3.052 6.24,3.229 0.323,0.177 10 false 3 5.875,3.948 6.198,4.125 0.323,0.177 10 false 46 5.875,4.469 6.198,4.646 0.323,0.177 10 false 59 6.156,1.896 6.646,2.073 0.49,0.177 10 false IGSW 6.146,3.24 6.635,3.417 0.49,0.177 10 false +B2 6.146,2.844 6.635,3.021 0.49,0.177 10 false +B 6.146,4.031 6.635,4.208 0.49,0.177 10 false MREL 6.156,4.667 6.646,4.844 0.49,0.177 10 false E1 6.427,5.177 6.917,5.354 0.49,0.177 10 false ECM 2.542,4.604 4.167,4.979 1.625,0.375 10 false No. 1 Integration Relay 4.354,3.24 4.677,3.417 0.323,0.177 10 false 1B 4.406,1.802 4.729,1.979 0.323,0.177 10 false 9 4.792,2.135 5.771,2.448 0.979,0.313 10 false ECU-IG2 NO. 1 5.208,3.823 6.188,4.135 0.979,0.313 10 false EFI NO. 2 5.635,3.521 5.958,3.698 0.323,0.177 10 false 2 5.333,3.521 5.656,3.698 0.323,0.177 10 false 1 4.406,3.042 4.729,3.219 0.323,0.177 10 false 4 4.354,4.135 4.677,4.313 0.323,0.177 10 false 1B 1.792,3.417 2.115,3.594 0.323,0.177 10 false 6 2.958,3.833 3.938,4.146 0.979,0.313 10 false EFI-MAIN 2.958,2.594 3.938,2.906 0.979,0.313 10 false IG2 NO. 1 0.76,3.385 1.74,3.698 0.979,0.313 10 false EFI-MAIN 1.76,3.24 2.083,3.417 0.323,0.177 10 false 1B 1.813,3.052 2.135,3.229 0.323,0.177 10 false 3 1.76,1.99 2.083,2.167 0.323,0.177 10 false 1A 1.771,1.813 2.094,1.99 0.323,0.177 10 false 10 0.771,2.135 1.75,2.448 0.979,0.313 10 false IG2-MAIN 0.385,3.677 1.365,3.99 0.979,0.313 10 false BATT-MAIN 0.563,4.365 1.115,4.969 0.552,0.604 10 false Auxiliary Battery 1.76,2.323 2.083,2.5 0.323,0.177 10 false 1A 1.813,2.167 2.135,2.344 0.323,0.177 10 false 8 1.75,3.573 2.073,3.75 0.323,0.177 10 false 1B 4.385,3.927 4.708,4.104 0.323,0.177 10 false 5

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF NO. 1 INTEGRATION RELAY)
a.

Disconnect the 1A No. 1 integration relay connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1A-10 - Body ground Always 11 to 14 V
1B-3 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.INSPECT NO. 1 INTEGRATION RELAY (EFI-MAIN RELAY, IG2 NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (AUXILIARY BATTERY - NO. 1 INTEGRATION RELAY)

2.INSPECT NO. 1 INTEGRATION RELAY (EFI-MAIN RELAY, IG2 NO. 1 RELAY)
a.

Inspect the No. 1 integration relay (EFI-MAIN relay, IG2 NO. 1 relay).

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)
a.

Remove the No. 1 integration relay.


b.

Disconnect the A38 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1A-9 - A38-6 (IGSW) Always Below 1 Ω
1B-6 - A38-46 (MREL) Always Below 1 Ω
1B-4 - A38-2 (+B) Always Below 1 Ω
1B-4 - A38-3 (+B2) Always Below 1 Ω
1A-9 or A38-6 (IGSW) - Body ground and other terminals Always 10 kΩ or higher
1B-6 or A38-46 (MREL) - Body ground and other terminals Always 10 kΩ or higher
1B-4 or A38-2 (+B) - Body ground and other terminals Always 10 kΩ or higher
1B-4 or A38-3 (+B2) - Body ground and other terminals Always 10 kΩ or higher



HINT:

If a short is detected in any of the above circuits, there may be a malfunction in the circuit of a connected ECU.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - BODY GROUND)
a.

Remove the No. 1 integration relay.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1A-8 - Body ground Always Below 1 Ω
1B-5 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the C63 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C63-59 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.INSPECT ECM (IGSW VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT ECM (IGSW VOLTAGE)
C267933C74
1.594,0.073 2,0.302 0.406,0.229 1.813,1.938 1.844,0.896 true 1.677,0.125 2.135,0.323 0.458,0.198 10 false A38 1.677,1.969 2.135,2.146 0.458,0.177 10 false IGSW 0.083,0.063 0.542,0.26 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to ECM)


a.

Disconnect the ECM connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A38-6 (IGSW) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INTEGRATION RELAY)
7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INTEGRATION RELAY)
a.

Disconnect the F1 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the 1A No. 1 integration relay connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F1-17 (IG1D) - 1A-7 Always Below 1 Ω
F1-17 (IG1D) or 1A-7 - Body ground and other terminals Always 10 kΩ or higher



HINT:

If a short is detected in any of the above circuits, there may be a malfunction in the circuit of a connected ECU.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR