Home › Engine / Hybrid System › 2ZR-FXE (ENGINE CONTROL) › THROTTLE BODY
RM32K0E _51 Engine / Hybrid System _060312 2ZR-FXE ENGINE CONTROL _0295701 THROTTLE BODY A

2ZR-FXE ENGINE CONTROL  THROTTLE BODY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during throttle body assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
·

Replacement of throttle body assembly

·

Cleaning the deposits from the throttle body assembly


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

PROCEDURE

Hide 51441 1.REMOVE NO. 1 ENGINE UNDER COVER

Hide 2.DRAIN ENGINE COOLANT (for Engine)

Hide 17705 3.REMOVE AIR CLEANER CAP SUB-ASSEMBLY

a.
A374999

Disconnect the mass air flow meter connector.


b.

Disconnect the wire harness clamp.


c.
A375000C01
2.99,1.365 3.177,1.542 0.188,0.177 10 true *a 3,0.729 3.188,0.906 0.188,0.177 10 true *a 0.885,0.49 1.073,0.646 0.188,0.156 10 true *b 0.865,1.667 1.052,1.844 0.188,0.177 10 true *b
*a Clamp
*b Guide


Disengage the 2 clamps.


d.

Disengage the 2 guides and remove the air cleaner cap sub-assembly from the air cleaner case sub-assembly.


e.

Loosen the hose clamp and remove the air cleaner cap sub-assembly from the air cleaner hose assembly.


Hide 4.REMOVE AIR CLEANER HOSE ASSEMBLY

a.
A375001

Slide the clip and disconnect the No. 2 ventilation hose from the cylinder head cover sub-assembly.


b.

Loosen the hose clamp and remove the air cleaner hose assembly from the throttle body assembly.


Hide 22210 5.REMOVE THROTTLE BODY ASSEMBLY

a.
A375002C01
1.844,1.917 2.063,2.094 0.219,0.177 10 true *1 0.875,1.875 1.094,2.052 0.219,0.177 10 true *2 0.021,0.021 0.281,0.229 0.26,0.208 12 false *A 0.052,2.354 0.313,2.563 0.26,0.208 12 false *B 1.781,4.313 2,4.49 0.219,0.177 10 true *1 0.844,4.281 1.063,4.458 0.219,0.177 10 true *2
*A w/ Stud Bolt
*B w/o Stud Bolt
*1 Water By-pass Hose
*2 No. 2 Water By-pass Hose


Disconnect the throttle body assembly connector.


b.

Slide the 2 clips and disconnect the water by-pass hose and No. 2 water by-pass hose from the throttle body assembly.


c.
A378096C01
0.052,0.042 0.323,0.25 0.271,0.208 12 false *A 0.083,2.313 0.354,2.521 0.271,0.208 12 false *B
*A w/ Stud Bolt
*B w/o Stud Bolt


w/ Stud Bolt:

i.

Remove the 2 bolts, 2 nuts and throttle body assembly from the intake manifold.



d.

w/o Stud Bolt:

i.

Remove the 4 bolts and throttle body assembly from the intake manifold.



Hide 22271 6.REMOVE THROTTLE BODY GASKET

a.
A375003C01
0.052,0.042 0.313,0.24 0.26,0.198 12 true *A 0.083,2.333 0.344,2.531 0.26,0.198 12 true *B
*A w/ Stud Bolt
*B w/o Stud Bolt


Remove the throttle body gasket from the intake manifold.