Home › General › MAINTENANCE › 2ZR-FXE COOLANT (for Engine Coolant) › 2016.10–2019.09
RM32K0E _V1 General _059911 MAINTENANCE _0299523 2ZR-FXE COOLANT(for Engine Coolant) A

MAINTENANCE  2ZR-FXE COOLANT(for Engine Coolant)  REPLACEMENT  


CAUTION / NOTICE / HINT

CAUTION:
A389825

Do not remove the reserve tank cap, air release valve or radiator drain cock plug while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.


PROCEDURE

Hide 51441 1.REMOVE NO. 1 ENGINE UNDER COVER

Hide 2.DRAIN ENGINE COOLANT (for Engine)

CAUTION:

Do not remove the reserve tank cap, air release valve or radiator drain cock plug while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.


a.
A396420C01
1.75,4.167 2.083,4.167 false 1.083,2.052 1.417,2.052 true 2.135,4.094 2.448,4.292 0.313,0.198 10 false *a 0.844,1.927 1.063,2.115 0.219,0.188 10 true *a
*a Hose


Connect a hose with an inside diameter of 9 mm (0.354 in.) to the radiator drain cock as shown in the illustration.


b.
A391007C02
1.958,0.281 1.583,0.281 false 1.198,0.396 0.823,0.396 false 2.771,2.813 2.396,2.813 false 2,0.198 2.313,0.354 0.313,0.156 10 false *1 2.813,2.729 3.125,2.885 0.313,0.156 10 false *2 0.667,0.302 0.979,0.458 0.313,0.156 10 false *a
*1 Reserve Tank Cap
*2 Radiator Drain Cock Plug
*a Air Release Valve


Loosen the radiator drain cock plug.


c.

Remove the reserve tank cap. Then drain the engine coolant.

HINT:

Collect the engine coolant in a container and dispose of it according to the regulations in your area.



d.

Tighten the radiator drain cock plug by hand.


e.

Disconnect the hose from the radiator drain cock.


Hide 3.ADD ENGINE COOLANT (for Engine)

a.
A390663C01
2.01,0.896 2.125,0.51 2.125,0.51 2.281,0.51 true 1.552,2.563 1.958,2.563 true 2.344,0.406 2.625,0.615 0.281,0.208 10 true *a 1.99,2.469 2.271,2.677 0.281,0.208 10 true *a
*a Air Release Valve


Using a 6 mm hexagon socket wrench, remove the air release valve from the radiator reserve tank assembly.


b.
A391008

Add coolant to the level shown in the illustration.

Specified Capacity:

5.4 liters (5.7 US qts, 4.7 Imp. qts)


NOTICE:

Do not substitute plain water for engine coolant.


HINT:

TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damaging the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).



c.

Squeeze the No. 1 radiator hose and No. 2 radiator hose several times by hand, and then check the level of the engine coolant.

If the engine coolant level is low, add engine coolant.


d.

Using a 6 mm hexagon socket wrench, install the air release valve to the radiator reserve tank assembly.

Torque:
2.0 N*m (20 kgf*cm, 18 in.*lbf)


e.

Install the reserve tank cap.

NOTICE:

Securely tighten the reserve tank cap as much as possible.



f.

Put the engine in inspection mode (maintenance mode).

i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch to ON (IG).


iii.

Turn the GTS on.


iv.

Enter following menus: Powertrain / Hybrid Control / Utility / Inspection Mode.

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103


g.

Bleed air from the cooling system.

NOTICE:
·

Before starting the engine, turn the A/C switch off.

·

Adjust the heater control to the maximum hot setting.

·

Adjust the blower speed to the low setting.



i.
A448591C04
1.563,0.75 1.719,0.417 1.719,0.417 1.885,0.417 false 1.927,0.323 2.24,0.531 0.313,0.208 10 true *a
*a Compartment 1


Warm up the engine until the water inlet with thermostat sub-assembly opens. While the water inlet with thermostat sub-assembly is open, circulate the engine coolant for several minutes.

HINT:

The water inlet with thermostat sub-assembly open timing can be confirmed by squeezing the No. 2 radiator hose by hand, and sensing vibrations when the engine coolant starts to flow inside the No. 2 radiator hose.



ii.

Squeeze the No. 1 radiator hose and No. 2 radiator hose several times by hand to bleed air from the system.

CAUTION:
When squeezing the No. 1 radiator hose and No. 2 radiator hose:
·

Wear protective gloves.

·

Be careful as the No. 1 radiator hose and No. 2 radiator hose are hot.

·

Keep your hands away from the fan LH and fan RH.



NOTICE:
·

Make sure that the radiator reserve tank assembly still has some engine coolant in it.

·

If the coolant temperature gauge indicates an excessive temperature, turn off the engine and let it cool.

·

If there is not enough engine coolant, the engine may overheat or be seriously damaged.




iii.

Confirm that the engine coolant level in compartment 1 of the radiator reserve tank assembly is full.



h.

Stop the engine and wait until the engine coolant has cooled. (*2)


i.
A448592C02
1.042,1.406 1.26,1.406 1.26,1.406 1.563,1.073 false 1.021,1.677 1.208,1.677 1.208,1.677 1.615,1.24 false 2.198,1.188 2.625,1.188 false 0.875,1.302 1.188,1.458 0.313,0.156 10 false *a 0.854,1.583 1.167,1.74 0.313,0.156 10 false *b 2.688,1.104 3,1.26 0.313,0.156 10 false *c 2.979,0.365 3.292,0.521 0.313,0.156 10 false *d
*a FULL Line
*b LOW Line
*c Compartment 1
*d Engine Coolant Level


With the engine coolant level of the radiator reserve tank assembly between the FULL and LOW lines, confirm that the radiator reserve tank assembly No. 1 is full. (*3)

·

If the engine coolant level is below the LOW line, add engine coolant at the specified concentration until the engine coolant level is at the FULL line, then repeat steps (*1) to (*3).

·

If the engine coolant level is above the FULL line, remove engine coolant until the engine coolant level is at the FULL line.



Hide 4.INSPECT FOR COOLANT LEAK (for Engine)

Hide 51441 5.INSTALL NO. 1 ENGINE UNDER COVER