Upon receiving the dynamic radar cruise control or brake hold control operating signal from the skid control ECU (brake booster with master cylinder assembly), the relay contact turns on and the stop lights come on.
| DTC No. | Detection Item | INF Code | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|---|
| C1380 | Stop Light Control Relay Malfunction | 761
762 |
·
INF Code: 761 -
When terminal BS voltage is 9.5 V or more, stop light drive output (STP0) is ON and STP2 is OFF for 2 seconds or more. ·
INF Code: 762 -
When terminal IG1 voltage is 9.5 V or more, stop light drive output (STP0) is OFF and the input signals for STP and STP2 differ for 5 seconds or more. |
·
INF Code: 761 -
STOP fuse -
Harness or connector -
Stop light switch assembly -
Skid control ECU (brake booster with master cylinder assembly) ·
INF Code: 762 -
STOP fuse -
Harness or connector -
Stop light switch assembly -
Skid control ECU (brake booster with master cylinder assembly) |
VSC DTC |
After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION
Inspect the fuses for circuits related to this system before performing the following procedure.
Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.
Turn the power switch off.
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly)) |
Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A39-12 (STP) - Body ground | Brake pedal depressed | 11 to 14 V |
| Brake pedal released | Below 1.5 V | |
| A39-22 (STPO) - Body ground | Always | 11 to 14 V |
| A39-37 (STP2) - Body ground | Brake pedal depressed | 11 to 14 V |
| Brake pedal released | Below 1.5 V |
| Result | Proceed to |
|---|---|
| All terminal voltage is normal | A |
| Only STP2 terminal voltage abnormal | B |
| Only STPO terminal voltage abnormal | C |
| Only STP terminal voltage abnormal | D |
| STPO terminal and STP2 terminal voltage abnormal | E |
A
B
C
D
E
Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.
Perform "Active Test" according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Stop Light Relay | Stop light control relay (Stop light switch assembly) | ON or OFF | Stop lights come on |
| Tester Display |
|---|
| Stop Light Relay |
Stop light turns ON/OFF in response to the GTS operation
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.
Perform "Active Test" according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Stop Light Relay | Stop light control relay (Stop light switch assembly) | ON or OFF | Stop lights come on |
| Tester Display |
|---|
| Stop Light Relay |
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC C1380 is output (for LHD) | A |
| DTC C1380 is output (for RHD) | B |
| DTC C1380 is not output | C |
A
B
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.
Perform "Active Test" according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Stop Light Relay | Stop light control relay (Stop light switch assembly) | ON or OFF | Stop lights come on |
| Tester Display |
|---|
| Stop Light Relay |
| *a | Component with harness connected
(Stop Light Switch Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A45-4 (ACC) - Body ground | Active Test is ON | Below 1.5 V |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly)) |
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
Disconnect the A49 hybrid vehicle control ECU connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A39-37 (STP2) - Body ground | Stop light switch assembly on (Brake pedal depressed) | 11 to 14 V |
| A39-37 (STP2) - Body ground | Stop light switch assembly off (Brake pedal released) | Below 1.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly)) |
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
Disconnect the M67 certification ECU (smart key ECU assembly) connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A39-37 (STP2) - Body ground | Stop light switch assembly on (Brake pedal depressed) | 11 to 14 V |
| A39-37 (STP2) - Body ground | Stop light switch assembly off (Brake pedal released) | Below 1.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly)) |
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
Disconnect the A45 stop light switch assembly connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A39-37 (STP2) - Body ground | Always | Below 1.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the power switch off.
Disconnect the A39 skid control ECU (brake booster with master cylinder assembly) connector.
Disconnect the A45 stop light switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A39-37 (STP2) - A45-3 (L) | Always | Below 1 Ω |
| A39-37 (STP2) or A45-3 (L) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the power switch off.
Disconnect the A39 skid control ECU (brake booster with master cylinder assembly) connector.
Disconnect the A45 stop light switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A39-22 (STPO) - A45-4 (ACC) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the power switch off.
Disconnect the A39 skid control ECU (brake booster with master cylinder assembly) connector.
Disconnect the M48 rear combination light assembly LH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A39-12 (STP) - Body ground | Brake pedal depressed | 11 to 14 V |
| A39-12 (STP) - Body ground | Brake pedal released | Below 1.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
for LED Type: Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY(for LED Type)>REMOVAL
for Bulb Type: Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY(for Bulb Type)>REMOVAL
NG
Turn the power switch off.
Disconnect the A39 skid control ECU (brake booster with master cylinder assembly) connector.
Disconnect the M48 rear combination light assembly LH connector.
Disconnect the M47 rear combination light assembly RH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A39-12 (STP) - Body ground | Brake pedal depressed | 11 to 14 V |
| A39-12 (STP) - Body ground | Brake pedal released | Below 1.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
for LED Type: Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY(for LED Type)>REMOVAL
for Bulb Type: Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY(for Bulb Type)>REMOVAL
NG
Turn the power switch off.
Disconnect the A39 skid control ECU (brake booster with master cylinder assembly) connector.
Disconnect the M48 rear combination light assembly LH connector.
Disconnect the M47 rear combination light assembly RH connector.
Disconnect the c1 center stop light assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A39-12 (STP) - Body ground | Brake pedal depressed | 11 to 14 V |
| A39-12 (STP) - Body ground | Brake pedal released | Below 1.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the power switch off.
Disconnect the A39 skid control ECU (brake booster with master cylinder assembly) connector.
Disconnect the M48 rear combination light assembly LH connector.
Disconnect the M47 rear combination light assembly RH connector.
Disconnect the c1 center stop light assembly connector.
Disconnect the A45 stop light switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A45-1 (OUT) - A39-12 (STP) | Always | Below 1 Ω |
| A45-1 (OUT) or A39-12 (STP) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the power switch off.
| *a | Front view of wire harness connector
(to Stop Light Switch Assembly) |
Disconnect the stop light switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A45-2 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A45-7 (B) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the power switch off.
Disconnect the A39 skid control ECU (brake booster with master cylinder assembly) connector.
Disconnect the A45 stop light switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A39-22 (STPO) - A45-4 (ACC) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG