Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM › 2016.10–2018.05
RM32K0E _54 Brake _060048 PARKING BRAKE _0296497 ELECTRIC PARKING BRAKE SYSTEM C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM  C13A2/22  Engine / Power Switch Malfunction  


DESCRIPTION

When the power switch is turned on (IG), power is supplied to the parking brake ECU assembly. This DTC is stored if IG power source voltage is not supplied to the parking brake ECU assembly when communication with other ECUs is established.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
C13A2/22 Engine / Power Switch Malfunction Both of following conditions are met:
1.

Power switch on (IG)

2.

When hybrid vehicle control ECU communicates with main body ECU (multiplex network body ECU) via CAN communication, IG power supply voltage is not received for approximately 3 seconds.


·

Wire harness or connector

·

IG power source circuit

·

Parking brake ECU assembly


DTC stored An electric parking brake system malfunction is displayed on the multi-information display.

WIRING DIAGRAM

C367792E01
3.135,0.771 3.594,0.969 0.458,0.198 10 false M71 5.042,1.313 5.5,1.51 0.458,0.198 10 false M70 4.542,1.313 5,1.51 0.458,0.198 10 false GND1 3.552,0.771 4.01,0.969 0.458,0.198 10 false IG 1.521,0.958 2.615,1.219 1.094,0.26 10 false ECU-IG1 NO. 1 2.146,1.875 3.24,2.135 1.094,0.26 10 false to CAN 1.021,3.26 3.656,3.667 2.635,0.406 10 false : CAN Communication Line 3.333,2.479 5.969,2.885 2.635,0.406 10 false Parking Brake ECU Assembly 3.219,0.563 3.375,0.76 0.156,0.198 10 false 5 5.115,1.115 5.271,1.313 0.156,0.198 10 false 9

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

The electric parking brake may still operate up to 20 seconds after the power switch is turned off. Before disconnecting connectors or fuses, turn the power switch off and wait 20 seconds or more.

·

When replacing the parking brake ECU assembly, operate the electric parking brake switch (electric parking brake switch assembly) as the parking brake indicator light (red) blinks when the power switch is first turned on (IG).



PROCEDURE

1.READ VALUE USING GTS (IG SWITCH)
a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Electric Parking Brake / Data List.


f.

Read the Data List according to the display on the GTS.

Chassis > Electric Parking Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
IG Switch IG power source status OFF or ON OFF: IG power source voltage is not input to skid control ECU (brake booster with master cylinder assembly)
ON: IG power source voltage is input to skid control ECU (brake booster with master cylinder assembly)
-
Chassis > Electric Parking Brake > Data List
Tester Display
IG Switch
50003 184 601
Result:
Proceed to
OK
NG




OK

2.CHECK DTC

NG

3.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU ASSEMBLY - POWER SOURCE AND BODY GROUND)
2.CHECK DTC
a.

Clear the DTCs.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > Electric Parking Brake > Clear DTCs
50002 184

b.

Turn the power switch off.


c.

Check for DTCs.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > Electric Parking Brake > Trouble Codes
50001 184

Result:
Result Proceed to
DTCs are output A
DTCs are not output B



A

REPLACE PARKING BRAKE ECU ASSEMBLY

B

3.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU ASSEMBLY - POWER SOURCE AND BODY GROUND)
a.

Disconnect the M71 and M70 parking brake ECU assembly connectors.

C319567C11
2.063,0.698 2.458,0.917 0.396,0.219 4.75,0.698 5.146,0.917 0.396,0.219 2,2.177 2.188,1.583 true 4.688,2.208 4.844,1.708 true 0.156,0.125 0.458,0.323 0.302,0.198 10 false *a 2.125,0.719 2.427,0.917 0.302,0.198 10 false M71 4.813,0.719 5.115,0.917 0.302,0.198 10 false M70 1.917,2.219 2.219,2.417 0.302,0.198 10 false IG 4.531,2.25 4.927,2.448 0.396,0.198 10 false GND1
*a Front view of wire harness connector
(to Parking Brake ECU Assembly)
- -



b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M71-5 (IG) - Body ground Power switch on (IG) 11 to 14 V



d.

Turn the power switch off.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M70-9 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPAIR IG POWER SOURCE CIRCUIT

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR