Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM › 2016.10–2018.05
RM32K0E _54 Brake _060048 PARKING BRAKE _0296497 ELECTRIC PARKING BRAKE SYSTEM C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM  C13A6/42  Open or Short in Circuit of Motor  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
C13A6/42 Open or Short in Circuit of Motor Both of following conditions are met:
1.

Power switch on (IG) or electric parking brake switch (electric parking brake switch assembly) pulled to lock side with power switch off.

2.

Power supply voltage and +B voltage are normal, but parking brake motor circuit is malfunctioning for approximately 1 to 2 seconds.


·

Parking brake actuator assembly

·

Wire harness or connector

·

Parking brake ECU assembly


DTC stored An electric parking brake system malfunction is displayed on the multi-information display.

DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Power switch on (IG) ○ -
Electric parking brake switch (electric parking brake switch assembly) pulled to lock side with power switch off - ○
Malfunction Status Power supply voltage and +B voltage are normal, but motor circuit is malfunctioning ○ ○
Detection Time Approximately 1 to 2 second Approximately 1 to 2 second
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C320708E13
1.333,0.729 1.75,0.917 0.417,0.188 10 false MRR- 1.292,1.313 1.813,1.552 0.521,0.24 10 false MRR+ 1.313,3.875 1.729,4.063 0.417,0.188 10 false MRL+ 1.333,3.292 1.75,3.479 0.417,0.188 10 false MRL- 3.979,0.729 4.396,0.917 0.417,0.188 10 false MRR- 5.354,0.729 5.896,0.979 0.542,0.25 10 false MRR- 3.979,1.323 4.396,1.51 0.417,0.188 10 false MRR+ 5.354,1.323 5.927,1.646 0.573,0.323 10 false MRR+ 3.969,3.292 4.385,3.479 0.417,0.188 10 false MRL- 5.344,3.292 5.76,3.479 0.417,0.188 10 false MRL- 3.958,3.896 4.375,4.083 0.417,0.188 10 false MRL+ 5.344,3.885 5.76,4.073 0.417,0.188 10 false MRL+ 3.594,0.698 4.01,0.885 0.417,0.188 10 false dM2 3.594,1.292 4.01,1.479 0.417,0.188 10 false dM2 3.583,3.281 4,3.469 0.417,0.188 10 false eM2 3.583,3.875 4,4.063 0.417,0.188 10 false eM2 5.01,0.698 5.292,0.885 0.281,0.188 10 false d2 5.01,1.292 5.292,1.479 0.281,0.188 10 false d2 5.01,3.281 5.292,3.469 0.281,0.188 10 false e2 5.01,3.875 5.292,4.063 0.281,0.188 10 false e2 1.802,0.604 1.99,0.802 0.188,0.198 10 false 3 1.802,1.198 1.99,1.396 0.188,0.198 10 false 1 1.813,3.177 2,3.375 0.188,0.198 10 false 6 1.813,3.771 2,3.969 0.188,0.198 10 false 4 0.375,4.417 0.792,4.604 0.417,0.188 10 false M70 0.375,4.573 2.24,4.906 1.865,0.333 10 false Parking Brake ECU Assembly 3.74,4.427 5.042,4.979 1.302,0.552 10 false NO. 2 Parking Brake Wire Assembly 5.115,4.417 6.552,4.927 1.438,0.51 10 false Parking Brake Actuator Assembly LH 3.677,1.833 4.979,2.302 1.302,0.469 10 false NO. 1 Parking Brake Wire Assembly 5.094,1.844 6.604,2.375 1.51,0.531 10 false Parking Brake Actuator Assembly RH 4.49,3.896 4.906,4.083 0.417,0.188 10 false MRL+ 4.479,3.292 4.896,3.479 0.417,0.188 10 false MRL- 4.448,1.313 4.865,1.5 0.417,0.188 10 false MRR+ 4.458,0.719 4.875,0.906 0.417,0.188 10 false MRR- 3.688,0.51 3.844,0.708 0.156,0.198 10 false 2 5.052,0.51 5.208,0.708 0.156,0.198 10 false 1 5.052,1.104 5.208,1.302 0.156,0.198 10 false 2 3.677,1.104 3.833,1.302 0.156,0.198 10 false 1 3.677,3.083 3.833,3.281 0.156,0.198 10 false 2 5.052,3.094 5.208,3.292 0.156,0.198 10 false 1 5.052,3.688 5.208,3.885 0.156,0.198 10 false 2 3.667,3.688 3.823,3.885 0.156,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

The electric parking brake may still operate up to 20 seconds after the power switch is turned off. Before disconnecting connectors or fuses, turn the power switch off and wait 20 seconds or more.

·

When replacing the parking brake ECU assembly, operate the electric parking brake switch (electric parking brake switch assembly) as the parking brake indicator light blinks (red) when the power switch is first turned on (IG).



PROCEDURE

1.READ VALUE USING GTS (PERMISSION OF RH INTERLOCKING PKB LOCK / PERMISSION OF LH INTERLOCKING PKB LOCK)
a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Electric Parking Brake / Data List.


f.

Read the Data List according to the display on the GTS.

Chassis > Electric Parking Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Permission of RH Interlocking PKB Lock Parking brake actuator assembly RH parking brake lock control permission status OK or NG OK -
Permission of LH Interlocking PKB Lock Parking brake actuator assembly LH parking brake lock control permission status OK or NG OK -
Chassis > Electric Parking Brake > Data List
Tester Display
Permission of RH Interlocking PKB Lock
Permission of LH Interlocking PKB Lock
50003 184 632,636
Result:
Proceed to
NEXT




NEXT

2.INSPECT PARKING BRAKE WIRE ASSEMBLY
2.INSPECT PARKING BRAKE WIRE ASSEMBLY
C360728C03
1.854,0.667 2.188,0.833 0.333,0.167 1.854,0.417 2.188,0.583 0.333,0.167 4.979,0.333 5.313,0.5 0.333,0.167 4.979,0.583 5.313,0.75 0.333,0.167 1.417,2.083 1.875,1.625 true 1.833,1.458 1.417,1 true 2.167,1.458 2.583,1 true 2.167,1.625 2.583,2.083 true 5,1.417 4.5,1 true 4.5,2.083 5,1.583 true 5.313,1.583 5.75,2.083 true 5.313,1.417 5.75,1 true 2.25,0.417 2.51,0.615 0.26,0.198 10 false *d 2.25,0.667 2.521,0.865 0.271,0.198 10 false *e 0.167,0.167 0.479,0.323 0.313,0.156 10 false *a 1.917,2.094 2.229,2.25 0.313,0.156 10 false *b 5.083,2.094 5.396,2.25 0.313,0.156 10 false *c 1.885,0.417 2.281,0.615 0.396,0.198 10 false dM2 1.885,0.667 2.344,0.865 0.458,0.198 10 false eM2 5.063,0.333 5.375,0.531 0.313,0.198 10 false d2 5.063,0.583 5.375,0.781 0.313,0.198 10 false e2 5.417,0.333 5.688,0.542 0.271,0.208 10 false *d 5.417,0.583 5.698,0.792 0.281,0.208 10 false *e 0.823,0.823 1.26,1.021 0.438,0.198 10 false MRR+ 0.833,2.063 1.25,2.25 0.417,0.188 10 false MRL+ 2.625,2.073 3.031,2.26 0.406,0.188 10 false MRL- 2.615,0.833 3.042,1.031 0.427,0.198 10 false MRR- 3.938,0.823 4.323,1.021 0.385,0.198 10 false MRR- 3.969,2.083 4.354,2.281 0.385,0.198 10 false MRL- 5.781,0.813 6.208,1.01 0.427,0.198 10 false MRR+ 5.802,2.073 6.219,2.26 0.417,0.188 10 false MRL+ 1.208,0.813 1.448,1.01 0.24,0.198 10 false *d 1.198,2.052 1.458,2.26 0.26,0.208 10 false *e 2.979,0.813 3.219,1.01 0.24,0.198 10 false *d 2.969,2.063 3.229,2.271 0.26,0.208 10 false *e 4.292,0.813 4.531,1.01 0.24,0.198 10 false *d 6.167,0.792 6.406,0.99 0.24,0.198 10 false *d 4.302,2.073 4.563,2.281 0.26,0.208 10 false *e 6.167,2.052 6.427,2.26 0.26,0.208 10 false *e
*a Front view of Parking Brake Wire Assembly *b (to wire harness connector)
*c (to Parking Brake Actuator Assembly) *d RH
*e LH - -


a.

Remove the parking brake wire assembly.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>REMOVAL


b.

Check the parking brake wire assembly for damage.

OK:

No damage.


HINT:

If damaged, there may be a short in the wire harness or a short to ground.



c.

Inspect the parking brake wire assembly.

Standard Resistance:
RH
Tester Connection Condition Specified Condition
dM2-2 (MRR-) - d2-1 (MRR-) Always Below 1 Ω
dM2-2 (MRR-) - d2-2 (MRR+) Always 10 kΩ or higher
dM2-2 (MRR-) or d2-1 (MRR-) - Body ground Always 10 kΩ or higher
dM2-1 (MRR+) - d2-2 (MRR+) Always Below 1 Ω
dM2-1 (MRR+) - d2-1 (MRR-) Always 10 kΩ or higher
dM2-1 (MRR+) or d2-2 (MRR+) - Body ground Always 10 kΩ or higher

LH
Tester Connection Condition Specified Condition
eM2-2 (MRL-) - e2-1 (MRL-) Always Below 1 Ω
eM2-2 (MRL-) - e2-2 (MRL+) Always 10 kΩ or higher
eM2-2 (MRL-) or e2-1 (MRL-) - Body ground Always 10 kΩ or higher
eM2-1 (MRL+) - e2-2 (MRL+) Always Below 1 Ω
eM2-1 (MRL+) - e2-1 (MRL-) Always 10 kΩ or higher
eM2-1 (MRL+) or e2-2 (MRL+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU ASSEMBLY - PARKING BRAKE ACTUATOR ASSEMBLY)

NG

REPLACE PARKING BRAKE WIRE ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU ASSEMBLY - PARKING BRAKE ACTUATOR ASSEMBLY)
a.

Turn the power switch off.


b.

Make sure the parking brake wire assembly is securely installed.


c.

Disconnect the M70 parking brake ECU assembly connector.


d.

Disconnect the d2 or e2 parking brake actuator assembly connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
RH
Tester Connection Condition Specified Condition
M70-1 (MRR+) - d2-2 (MRR+) Always Below 1 Ω
M70-3 (MRR-) - d2-1 (MRR-) Always Below 1 Ω
M70-1 (MRR+) or d2-2 (MRR+) - Body ground Always 10 kΩ or higher
M70-3 (MRR-) or d2-1 (MRR-) - Body ground Always 10 kΩ or higher

LH
Tester Connection Condition Specified Condition
M70-4 (MRL+) - e2-2 (MRL+) Always Below 1 Ω
M70-6 (MRL-) - e2-1 (MRL-) Always Below 1 Ω
M70-4 (MRL+) or e2-2 (MRL+) - Body ground Always 10 kΩ or higher
M70-6 (MRL-) or e2-1 (MRL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT PARKING BRAKE ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT PARKING BRAKE ACTUATOR ASSEMBLY
a.

Inspect the parking brake actuator assembly.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE PARKING BRAKE ECU ASSEMBLY

NG

REPLACE PARKING BRAKE ACTUATOR ASSEMBLY