Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM › 2016.10–2018.05
RM32K0E _54 Brake _060048 PARKING BRAKE _0296497 ELECTRIC PARKING BRAKE SYSTEM C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM  C13AD/23  Open in +B Circuit  


DESCRIPTION

The parking brake ECU assembly operates the parking brake motor RH and LH with power supplied from the +B and +B2 terminals.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
C13AD/23 Open in +B Circuit All of following conditions are met:
1.

Power switch on (IG) or electric parking brake switch (electric parking brake switch assembly) pulled to lock side with power switch off.

2.

When parking brake motor is not operating, Motor +B voltage is Mid or when parking brake motor is operating, Motor +B voltage is Lo

3.

When parking brake motor is not operating, malfunction is detected for approximately 1 second

When parking brake motor is operating, malfunction is detected for approximately 0.5 seconds


·

Wire harness or connector

·

Parking brake ECU assembly


DTC stored An electric parking brake system malfunction is displayed on the multi-information display.

DTC Detection Conditions:
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4
Diagnosis Condition Power switch on (IG) ○ - ○ -
Electric parking brake switch (electric parking brake switch assembly) pushed to release side with power switch off - ○ - ○
Malfunction Status When parking brake is not operating: Motor +B voltage is Mid ○ ○ - -
When parking brake is operating: Motor +B voltage is Lo - - ○ ○
Detection Time Approximately 1 second Approximately 1 second Approximately 0.5 seconds Approximately 0.5 seconds
Number of Trips 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.

*: When the auxiliary battery voltage is 12 V.



WIRING DIAGRAM

C319569E08
1.802,1.083 2.563,1.281 0.76,0.198 10 false EPB NO. 1 1.813,1.875 2.573,2.073 0.76,0.198 10 false EPB NO. 2 4.083,0.948 4.844,1.146 0.76,0.198 10 false +B 4.073,1.729 4.833,1.927 0.76,0.198 10 false +B2 3.875,0.813 4.01,0.979 0.135,0.167 10 false 7 3.813,1.594 4,1.792 0.188,0.198 10 false 12 3.865,2.448 4.229,2.635 0.365,0.188 10 false M70 3.875,2.615 6.313,3 2.438,0.385 10 false Parking Brake ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

The electric parking brake may still operate up to 20 seconds after the power switch is turned off. Before disconnecting connectors or fuses, turn the power switch off and wait 20 seconds or more.

·

When replacing the parking brake ECU assembly, operate the electric parking brake switch (electric parking brake switch assembly) as the parking brake indicator light blinks (red) when the power switch is first turned on (IG).



PROCEDURE

1.READ VALUE USING GTS (ECU +B1 VOLTAGE / ECU +B2 VOLTAGE)
a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Electric Parking Brake / Data List.


f.

Check the Data List.

Chassis > Electric Parking Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RH Motor +B Voltage Parking brake motor RH (parking brake actuator assembly RH) +B voltage Lo, Mid or Hi Hi: Power switch on (IG) Mid: +B voltage is less than 8.5 V*
Lo: +B voltage is less than 3.5 V*
HINT:

*: When the auxiliary battery voltage is 12 V.


LH Motor +B Voltage Parking brake motor LH (parking brake actuator assembly LH) +B voltage Lo, Mid or Hi Hi: Power switch on (IG) Mid: +B voltage is less than 8.5 V*
Lo: +B voltage is less than 3.5 V*
HINT:

*: When the auxiliary battery voltage is 12 V.


Chassis > Electric Parking Brake > Data List
Tester Display
RH Motor +B Voltage
LH Motor +B Voltage
50003 184 427,428

Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU ASSEMBLY - AUXILIARY BATTERY)
2.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU ASSEMBLY - AUXILIARY BATTERY)
a.

Turn the power switch off.


b.

Disconnect the M70 parking brake ECU assembly connector.


c.
C319566C05
1.5,0.896 1.958,1.135 0.458,0.24 0.563,2.552 0.563,2.323 0.563,2.323 1.042,2.135 true 2.854,2.573 2.854,2.344 2.854,2.344 2.396,2.135 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 1.594,0.917 1.906,1.115 0.313,0.198 10 false M70 0.49,2.604 0.802,2.802 0.313,0.198 10 false +B 2.75,2.604 3.063,2.802 0.313,0.198 10 false +B2
*a Front view of wire harness connector
(to Parking Brake ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M70-7 (+B) - Body ground Always 11 to 14 V
M70-12 (+B2) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE PARKING BRAKE ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR