Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM32K0E _56 Audio / Visual / Telematics _060599 PARK ASSIST / MONITORING _0297239 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1ABE  Short to GND or Open in Buzzer  


DESCRIPTION

·

DTC C1ABE is stored when the blind spot monitor sensor RH (Slave) detects a ground short or open in the RCTA buzzer (blind spot monitor buzzer) circuit.


DTC No. Detection Item DTC Detection Condition Trouble Area
C1ABE Short to GND or Open in Buzzer
Both of the following conditions are met:
·

The blind spot monitor system is on.

·

The current flowing to the buzzer is below a specified value when buzzer operation voltage is being sent to the buzzer.


·

Blind spot monitor sensor RH (Slave)

·

RCTA buzzer (blind spot monitor buzzer)

·

Wire harness or connector



WIRING DIAGRAM

E362188E01
0.25,1.01 3.313,1.208 3.063,0.198 10 false from IG1-NO. 1 Relay 2.188,1.208 3.281,1.74 1.094,0.531 10 false ECU-IG1 NO. 4 3.583,1.531 5.177,2.188 1.594,0.656 10 false RCTA Buzzer (Blind Spot Monitor Buzzer) 3.594,1.344 4.052,1.542 0.458,0.198 10 false M64 5.51,1.958 5.969,2.156 0.458,0.198 10 false M63 5.51,2.135 7.156,2.708 1.646,0.573 10 false Blind Spot Monitor Sensor RH (Slave) 5.792,1.031 6.25,1.229 0.458,0.198 10 false BUZ 5.594,0.927 6.052,1.125 0.458,0.198 10 false 3 4.458,1.021 4.917,1.219 0.458,0.198 10 false BZN 3.635,1.01 4.094,1.208 0.458,0.198 10 false BZP 4.813,0.917 5.271,1.115 0.458,0.198 10 false 2 3.469,0.906 3.927,1.104 0.458,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

When checking for DTCs, make sure that the blind spot monitor system is turned on.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK DTC
a.

Turn the power switch off.


b.

Turn the power switch on (IG).


c.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (RCTA BUZZER - BLIND SPOT MONITOR SENSOR RH AND AUXILIARY BATTERY)
2.CHECK HARNESS AND CONNECTOR (RCTA BUZZER - BLIND SPOT MONITOR SENSOR RH AND AUXILIARY BATTERY)
a.

Disconnect the M64 RCTA buzzer (blind spot monitor buzzer) connector.


b.

Disconnect the M63 blind spot monitor sensor RH (Slave) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M64-2 (BZN) - M63-3 (BUZ) Always Below 1 Ω
M64-2 (BZN) or M63-3 (BUZ) - Body ground Always 10 kΩ or higher



d.
E360297C02
0.417,0.99 1,1.156 0.583,0.167 1.313,1.458 1.552,1.135 true 1.906,1.125 2.167,1.469 true 1.073,1.49 1.531,1.688 0.458,0.198 10 false BZP 2.167,1.5 2.625,1.698 0.458,0.198 10 false BZN 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 0.583,0.99 0.875,1.156 0.292,0.167 10 false M64
*a Component with harness connected
RCTA buzzer (blind spot monitor buzzer)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M64-1 (BZP) - Body ground Power switch on (IG) 11 to 14 V
M64-1 (BZP) - Body ground Power switch off Below 1 V



Result:
Proceed to
OK
NG



OK

3.CHECK RCTA BUZZER (BLIND SPOT MONITOR BUZZER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK RCTA BUZZER (BLIND SPOT MONITOR BUZZER)
a.

Replace the RCTA buzzer (blind spot monitor buzzer).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>REAR CROSSING TRAFFIC ALERT BUZZER>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Slave > Clear DTCs
50002 314

c.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314
OK:

DTC C1ABD and C1ABE are not output.



Result:
Proceed to
OK
NG



OK

END (RCTA BUZZER [BLIND SPOT MONITOR BUZZER] WAS DEFECTIVE)

NG