Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM32K0E _56 Audio / Visual / Telematics _060599 PARK ASSIST / MONITORING _0297239 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB2  Short to GND in Outer Mirror Indicator(Master)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH (Master) detects a short to ground in the outer rear view mirror indicator LH.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AB2 Short to GND in Outer Mirror Indicator(Master)
Both of the following conditions are met:
·

The blind spot monitor system is on


·

The current that is sent from the blind spot monitor sensor to the indicator is above a specified level for a specified period of time


·

Outer mirror LH

·

Outer rear view mirror assembly LH

·

Wire harness or connector

·

Blind spot monitor sensor LH (Master)



WIRING DIAGRAM

E221720E63
2.542,1.24 2.677,1.396 0.135,0.156 10 false 2 3.5,1.24 3.813,1.49 0.313,0.25 10 false 12 5.375,1.24 5.542,1.396 0.167,0.156 10 false 4 2.969,1.24 3.458,1.406 0.49,0.167 10 false BSL+ 5.573,1.333 5.979,1.49 0.406,0.156 10 false OMIL 3.24,1.719 3.615,1.885 0.375,0.167 10 false - 0.979,2.177 1.354,2.333 0.375,0.156 10 false IND1 0.75,3.396 1.198,3.552 0.448,0.156 10 false J7 5.448,3.396 5.896,3.552 0.448,0.156 10 false M62 2.354,1.344 2.49,1.5 0.135,0.156 10 false + 2.354,1.823 2.49,1.979 0.135,0.156 10 false - 2.552,1.729 2.688,1.885 0.135,0.156 10 false 1 3.51,1.719 3.75,1.896 0.24,0.177 10 false 9 0.969,2.677 3.104,2.844 2.135,0.167 10 false (Outer Mirror LH) 5.448,3.573 7.083,4.031 1.635,0.458 10 false Blind Spot Monitor Sensor LH (Master) 0.969,2.333 3.375,2.531 2.406,0.198 10 false Outer Rear View Mirror Indicator LH 0.76,3.625 3.135,3.802 2.375,0.177 10 false Outer Rear View Mirror Assembly LH

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor system is turned on.


PROCEDURE

1.CHECK DTC
a.

Turn the power switch off.


b.

Turn the power switch on (IG).


c.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Blind Spot Monitor Master > Trouble Codes
50001 313
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH (MASTER) - OUTER REAR VIEW MIRROR ASSEMBLY LH)
2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH (MASTER) - OUTER REAR VIEW MIRROR ASSEMBLY LH)
a.

Disconnect the M62 blind spot monitor sensor LH (Master) connector.


b.

Disconnect the J7 outer rear view mirror assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Always
M62-4 (OMIL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH
a.

Disconnect the IND1 outer mirror LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J7-12 (BSL+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT OUTER MIRROR LH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

4.INSPECT OUTER MIRROR LH

b.

Inspect the outer rear view mirror indicator LH on the outer mirror LH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE BLIND SPOT MONITOR SENSOR LH (MASTER)

NG