Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM32K0E _54 Brake _060044 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0294924 ELECTRONICALLY CONTROLLED BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  Brake Hold Standby Indicator Light Circuit  


DESCRIPTION

When the brake hold switch (electric parking brake switch assembly) is turned on with the power switch turned on (IG), the brake hold standby indicator light illuminates when brake hold operation is possible.

WIRING DIAGRAM

C349892E12
5.354,0.938 5.792,1.125 0.438,0.188 10 false CA1L 5.083,0.76 5.396,0.958 0.313,0.198 10 false 42 5.083,1.573 5.396,1.771 0.313,0.198 10 false 43 5.354,1.76 5.833,2.01 0.479,0.25 10 false CA1H 6.375,2.865 6.688,3.063 0.313,0.198 10 false IC 5.375,2.781 5.854,3.021 0.479,0.24 10 false CSW2 5.094,2.771 5.406,2.969 0.313,0.198 10 false 20 4.708,2.771 4.938,3.01 0.229,0.24 10 false 12 4.438,2.99 4.75,3.188 0.313,0.198 10 false +B 3.844,2.99 4.156,3.188 0.313,0.198 10 false E 3.656,2.781 3.969,2.979 0.313,0.198 10 false 8 3.063,3.208 3.375,3.406 0.313,0.198 10 false F67 3.042,3.365 5.26,3.75 2.219,0.385 10 false Brake Hold Switch (Electric Parking Brake Switch Assembly) 5.073,3.917 5.385,4.115 0.313,0.198 10 false A39 5.063,4.115 7.125,4.542 2.063,0.427 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 2.927,4.344 4.75,4.573 1.823,0.229 10 false : CAN Communication Line 0.125,3.917 0.438,4.115 0.313,0.198 10 false F4 0.115,4.073 1.938,4.479 1.823,0.406 10 false Combination Meter Assembly (Meter Circuit Plate) 0.896,1.74 1.354,1.969 0.458,0.229 10 false CANH 1.396,1.563 1.708,1.76 0.313,0.198 10 false 32 0.906,0.948 1.365,1.177 0.458,0.229 10 false CANL 1.396,0.76 1.708,0.958 0.313,0.198 10 false 31

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


PROCEDURE

1.PRE-CHECK
a.

If the brake hold standby indicator light does not illuminate even though the brake hold switch (electric parking brake switch assembly) is pushed, check that the brake hold function operation conditions are met.

1.

The driver's door is closed.

2.

Driver's seat belt is fastened.

3.

The engine hood is closed.

4.

The back door is closed.

5.

The system is normal.


Result:
Proceed to
NEXT




NEXT

2.CHECK CAN COMMUNICATION SYSTEM
2.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

3.CHECK IF BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY CONNECTOR IS SECURELY CONNECTED

B

3.CHECK IF BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake booster with master cylinder assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

4.INSPECT COMBINATION METER ASSEMBLY

NG

CONNECT CONNECTOR TO BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY CORRECTLY

4.INSPECT COMBINATION METER ASSEMBLY
a.

Connect the GTS to the DLC3.


b.

Turn the power switch off.


c.

Perform the Active Test of the combination meter assembly using the GTS.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Active Test
Tester Display
Indicat. Brake Hold
50004 122 72

d.

Check the combination meter assembly.

OK:

The brake hold standby indicator light turns on or off in accordance with the GTS operation.



Result:
Proceed to
OK
NG



OK

5.PERFORM ACTIVE TEST USING GTS (BRAKE HOLD STANDBY INDICATOR LIGHT)

NG

5.PERFORM ACTIVE TEST USING GTS (BRAKE HOLD STANDBY INDICATOR LIGHT)
a.

Turn the power switch on (IG).


b.

Select the Active Test on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
BH Standby Light Brake hold standby indicator light Indicator light ON/OFF Observe combination meter

c.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
BH Standby Light Brake hold standby indicator light ON or OFF ON: Indicator light on
OFF: Indicator light off
-
Chassis > ABS/VSC/TRC > Active Test
Active Test Display
BH Standby Light
Data List Display
BH Standby Light
50004 105 73 280

d.

Check the operating condition of the brake hold standby indicator light when operating it using the GTS.

Result:
Result Proceed to
Brake hold standby indicator light in the Data List does not change using the Active Test. (for LHD) A
Brake hold standby indicator light in the Data List does not change using the Active Test. (for RHD) B
Brake hold standby indicator light in the Data List turns ON/OFF using the Active Test. C




A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

6.INSPECT ELECTRIC PARKING BRAKE SWITCH ASSEMBLY
6.INSPECT ELECTRIC PARKING BRAKE SWITCH ASSEMBLY
a.

Remove the electric parking brake switch assembly.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SWITCH>REMOVAL


b.

Inspect the electric parking brake switch assembly.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

NG

REPLACE ELECTRIC PARKING BRAKE SWITCH ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)
a.

Disconnect the A39 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A39-20 (CSW2) - F67-12 (+B) Always Below 1 Ω
A39-20 (CSW2) or F67-12 (+B) - Body ground Always 10 kΩ or higher
F67-8 (E) - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR